Page 217 of 2490
4
. Tighten nuts securing stabilizer bar to links.
5. Lower four-post lift.
Page 218 of 2490
Rear Suspension - Stabilizer Bar Mounting Frame
Remo
val and Installation
Remov
a
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Ra
ise rear of vehicle and support
on stands. Refer to Section
100-02.
2. Support rear suspensio
n.
Posit
i
on a piece of wood under rear edge of suspension
unit.
Position an d
raise a jack
under wood to support
suspension unit.
3. Re
move monostrut lowe
r nuts and bolts.
4. Remove m
onostrut upper mounting
to body bracket securing
bolts.
5. Remove monostrut.
Lower rear edg
e
of suspension unit just sufficient for
access.
Exercising care to avoid dama ging fuel fil
ler neck drain
pipe, lift and withdraw monost rut from rear suspension.
Page 219 of 2490
Rear
Suspension -
Stabilizer Bar Mounting Frame Bushing
Re
moval and Installation
Remov
al
CAUTI
ON: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
I
nstallation
S
pecial Tool(s)
Adaptor Rin
g
204-116-01 (JD 143-1)
Anvil Adaptor
2
04-116-02 (JD 143-2)
R
emover/Replacer Adaptor
204-116-08 (JD 143-8)
D
ifferential Strut - Bush Replacer
204-201 (JD 241)
1. R
emove monostrut from
vehicle. Refer to operation 64.25.12.
2. Using a h
ydraulic press remove bush from monostrut.
Using special tools,
support monostrut on the press bed.
Posit
ion special tool on top of bush and align tool with
press ram.
Press bush from monostrut.
3. Clean relevant parts.
1. Using a hydraulic press, fi t bush into monostrut.
S
upport the bush-bore of the monostrut between
plates on the press-bed.
Page 220 of 2490
Positi
on bush to bore.
Positi
on special tool on top of bush and align tool with
press ram.
Press bush into monostrut.
2. Inst
all monostrut on vehicle.
Refer to operation 64.25.12 .
Page 221 of 2490
Rear
Suspension - Rear Wheel Bearing
Re
moval and Installation
S
pecial Tool(s)
Hub Holdin
g Tool
204-195 (JD227)
Hub Pu
ller
204-011 (JD 1D)
R
ear-Hub Remover
204-113 (JD 132)
Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/1)
Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/2)
D
river Handle
100-013 (18G-134)
Rear-hub spacer
replacer
204-003 (JD 15)
O
il Seal Remover/Replacer
Page 222 of 2490
Remova
l
2
05-2
34 (JD 550-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release handbrake.
2. Ra
ise the vehicle on a four-post lift.
3. Fully slacken bu
t do not remove parking brake cable adjuster
nut.
4. Relea s
e appropriate side parkin
g brake cable from connecting
clip.
5. With draw parkin
g brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.
Page 223 of 2490
9. P
osition special tool 204-195 on hub studs and install securing
nuts.
10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts and withdraw special tool (204-195)
from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.
14
.
Remove wheel speed sensor.
Disc
onnect wheel speed sensor harness from sensor
R
emove wheel speed sensor se
curing bolt and withdraw
sensor from hub carrier.
15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.
16. Remove hub nut and collar.
Re
move nut.
Page 224 of 2490
Remove l
ocating collar.
17 . Install a th
read protector on axle shaft.
18 . R
elease hub from axle shaft.
Pos
i
tion hub puller 204-011 on hub studs.
Inst
al
l securing nuts.
Progres
s
ively tighten
puller center bolt to release hub from
axle shaft splines.
19. Remove hub puller an d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.
20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.
Draw c
a
ble through suspension mounting bracket
aperture.
21. Remove parking brake cable to hub carrier grommet.