Page 169 of 2490
Rear Suspension - Axle B
ump Stop
Re
moval and Installation
Remov
al
CAUTI
ON: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
I
nstallation
1.
R
aise rear of vehicle and support
on stands. Refer to Section
100-02.
2. Remove appropriate road wheel. Refer to Section 100-02.
3. Remove bolts securing bump stop to body.
4. Remove bu
mp stop and where applicable, reinforcement
bracket from vehicle.
1. Position reinforcemen t brac
ket (where a
pplicable) and bump
stop on vehicle.
2. Install bump stop bolts and tighten to 26-34Nm.
Page 170 of 2490
3.
Install road wheel. Re fer to Secti
on 100-02.
4. Raise vehicle remove stands and lower vehicle. Refer to
Section 100-02.
Page 171 of 2490

Rear
Suspension - Rear Susp
ension and Axle Assembly
Re
moval and Installation
Remov
al
1.
CAUTI
ON: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-0
0 General
Informati
on
.
R
aise the rear of the vehicle
and support on axle stands.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin
g
.
2.
R
emove the rear wheels.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire
s
.
3. CAUTI
ON: Do not suspend the caliper from the brake
hose as this will damage the hose.
• NOTE: Right-hand shown, left-hand similar
Remove the brake calipers from the carriers.
1. Remove the caliper spring clip.
2. Remove the guide pin dust caps.
3. Slacken and withdr aw the guide pins.
4. Remove the caliper from the carrier and secure to the suspension mounting bracket using a tie strap.
4. NOTE
: Right-hand shown, left-hand similar
Disconnect the wheel speed sensor electrical connectors.
5. NOTE: Right-hand shown, left-hand similar
Remove and discard th e tie straps securing the wheel speed
sensor harnesses to the brake hose clips.
Page 172 of 2490
6. On
vehicles with adaptive damping:
R
e
move the top cover from
the shock absorbers.
Disc
onnect the shock absorber electrical connectors by
pressing the lugs down and pulling the connectors up.
7. NOTE : R
ight-hand shown, left-hand similar
Remove shock absorber upper mo unting plates to body nuts.
8. Fully slacken bu
t do not remove the parking brake cable
adjuster nut.
9. Release the parking brake cabl e from the connecting clip.
Page 173 of 2490
10
.
Withdraw the left-hand parking brake cable through the
equalizer.
11
.
Mark the position of the drive shaft coupling to the flexible
coupling.
12
.
Remove the drive shaft from the differential drive coupling.
R
emove the drive shaft to differential drive coupling bolts.
Carefully with
draw and lower the drive shaft from the
differential coupling.
13. CAUTION: Position a suitable piece of wood between the
jack and the rear suspension and axle assembly. Failure to follow
this instruction may result in damage to the vehicle.
Support the rear suspension and axle assembly.
Posi
tion a trolley jack under the rear suspension and axle
assembly.
Page 174 of 2490
Position a suitable piece o
f wood between the jack and the
rear suspension and axle assembly.
Rai s
e the jack to take the weight of the rear suspension
and axle assembly.
14 . NOTE
: Left-hand shown, right-hand similar
Remove the exhaust mounting to suspension bracket bolts.
15 . NOTE
: Right-hand shown, left-hand similar
Remove and discard the subframe front mounting brackets to
body bolts.
16 . NOTE
: Right-hand shown, left-hand similar
Remove the subframe front mounting brackets.
Remove an d discard the mount
ing bracket to subframe
bolts.
R e
move the front mounting bracket.
17. NOTE: Left-hand shown, right-hand similar
Remove differential strut upper mounting to body bracket
securing bolts.
Page 175 of 2490
I
nstallation
18
.
WARNING: With assistance, support the rear suspension
and axle assembly during remo val. Failure to follow this
instruction may result in personal injury.
Remove the rear suspensi on and axle assembly.
E
nsure that the hydr
aulic pipes, brake calipers, harnesses
and the drive shaft will not obstruct the rear suspension
and axle assembly during removal.
Carefull
y lower the rear suspen
sion and axle assembly and
traverse clear of vehicle.
19
.
Retrieve the subframe mounting bush shims.
20. With assistance, position th e rear suspension and axle
assembly on to a bench.
21. Clean the subframe mounting bushes and corresponding body
locations.
1. Apply a th
in coat of grease to the subframe bushes and place
the shims in position.
2. WARNING: With assistance, support the rear suspension
Page 176 of 2490

and axle assembly during installa
tion. Failure to follow this
instruction may result in personal injury.
CAUTION: Position a suitable piece of wood between the
jack and the rear suspension and axle assembly. Failure to follow
this instruction may result in damage to the vehicle.
Position the rear suspension and axle assembly on to a trolley
jack.
3. WARN
ING: With assistance, support the rear suspension
and axle assembly during instal lation. Failure to follow this
instruction may result in personal injury.
Position the rear suspension and axle assembly under the
vehicle.
4. WARN
ING: With assistance, support the rear suspension
and axle assembly during instal lation. Failure to follow this
instruction may result in personal injury.
Raise the trolley jack to position the rear suspension and axle
assembly to the vehicle.
5. NOTE : R
ight-hand shown, left-hand similar
Install the mounting brackets.
Po si
tion the mounting brackets to the subframe.
Install but do not tigh
ten
new bolts to the mounting
bracket .
6. NOTE: R
ight-hand shown, left-hand similar
Install new outer bolts to the mounting bracket.
Tigh te
n to 41-54 Nm.
7. NOTE: Right-hand shown, left-hand similar