Page 393 of 2490
Parking Brake and Ac
tuation - Pa
rking Brake Cable Adjustment
Gen
eral Procedures
1.
Raise rear of vehicle and support on stands. See section 100-
02.
2. Make sure gear selector is in neutral position.
3. Adjust parkin
g brake cable.
R
otate adjusting nut, until
the parking brake can be
applied by raising the parking brake lever 3 to 5 clicks.
4. CAUTION: Make sure that th e rear wheels rotate freely
when the parking brake lever is released.
Remove stands an d lower vehicle.
Page 394 of 2490

Parking Brake and Actuation - P
arking Brake Shoe
and Lining Adjustment
Gene
ral Procedures
1. Raise rear of vehicle and support on stands. See section 100-
02.
2. Remove both rear wheels.
3. Make sure that the parking br ake lever is in the released
position, and the gear selector lever is in neutral (N).
4. Alig
n brake disc access hole
with parking brake adjuster.
Instal
l three wheel nuts to secure brake disc to hub.
Tighten nuts to 20 Nm.
R e
move plug from access hole.
Rotate
brake disc un
til ac
cess hole is aligned with
adjuster.
5. Using a flat-bladed screwdriv er rotate the adjuster
anti
clockwise until the brake disc cannot be rotated.
6. NOTE : Th
e brake shoe return-spring next to the adjuster
prevents the adjuster from rota ting under normal operating
conditions. Make sure that the spring is seated between the
adjuster spokes, when brake adjustment is complete.
Rotate the adjuster gradually clockwise until the brake disc
rotates freely.
Inst al
l plug to access hole.
7. Repeat parking brake setting pr ocedure on opposite-side of
vehicle.
8. CAUTION: Make sure that th e rear wheels rotate freely
when the parking brake lever is released.
Adjust parking brake cable.
Ro
tate adjusting nut, until the parking brake can be
applied by raising the parking brake lever 3 to 5 clicks.
Page 395 of 2490
9.
Re
move wheel nuts.
10. Fit rear wheels. See section 204-04.
11. Remove stands an d lower vehicle.
Page 396 of 2490

Parking Brake and Actuation - P
arking Brake Control
Re
mo
val and Installation
Remov
a
l
W
A
RNING: BRAKE DUST, IF INHALED CAN DAMAGE YOUR
HEALTH. ALWAYS REMOVE BRAKE DUST USING A VACUUM
BRUSH. DO NOT USE A COMPRESSED-AIR LINE TO DISPERSE BRAKE DUST INTO THE ATMOSPHERE.
CAUTION: Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Position vehi cl
e on a four-post lift.
2. Release parking brake.
3. Releas
e tension on parking brake cable.
Slacken bu
t do not remove adjustment nut.
4. Releas
e parking brake cable.
Remo
ve clip.
Re
mo
ve clevis pin.
5. Remove driver seat for access . Refer to operation 76.70.01.
6. Remove trim from hand lever. Refer to operation 76.13.63.
7. Carefully reposition carpet from around hand lever for access.
8. Disconnect park ing-br
ake, warning-light switch connector.
9. Remove hand lever from vehicle.
Page 397 of 2490
I
nstallation
Re
move bolts.
R
emove lever.
10
.
Remove gasket.
11
.
Remove warning-light switch from lever.
R
emove screws.
Re
move switch.
1. Inst
all warning-light switch to hand lever.
Install and tigh
ten
screws to 3 Nm.
2. Install gasket to handbrake lever.
Page 398 of 2490
3. Instal
l hand lever to vehicle.
Install and tighten bolts to 2
2-28 Nm.
4. Connect park
ing-brake, warnin
g-light switch connector.
5. Reposition carpet.
6. Install trim to hand lever. Refer to operation 76.13.63.
7. Install driver seat. Refer to operation 76.70.01.
8. Make sure parking brake is in the released position.
9. Connect p a
rking brake cable.
Align ca
ble
.
Inst
al
l clevis pin.
Inst
al
l clip.
10. Adjust parking brake. Refer to operation 70.35.10.
Page 399 of 2490
Parking Brake and Act
uation - Parking Brake Control Shroud
Re
moval and Installation
Remov
al
Installation
1.
Position ha
ndbrake lever fully up.
2. Remove trim from handbrake lever.
1. Release press stud at to p of handbrake lever trim.
2. Ease lower moulding away from boss at base of lever and slide trim upwards.
1. Slide trim over handbrake lever and position lower moulding
over boss.
2. Fasten press stud at top of trim.
3. Check that 'J' gate selector is in position P.
4. Lower handbrake lever, checki ng for freedom of movement.
5. Pull handbrake lever fully up.
Page 400 of 2490

Parking Brake and Actuation - P
arking Brake Shoes
Re
mo
val and Installation
Remov
a
l
W
A
RNING: BRAKE DUST, IF INHALED CAN DAMAGE YOUR
HEALTH. ALWAYS REMOVE BRAKE DUST USING A VACUUM
BRUSH. DO NOT USE A COMPRESSED-AIR LINE TO DISPERSE BRAKE DUST INTO THE ATMOSPHERE.
CAUTION: Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Ra
ise rear of vehicle and support
on stands. Refer to section
100-02.
2. Remove both rear wheels.
3. Remove both rear brake discs. Refer to operation 70.10.13.
4. Re
move front shoe retaining pin.
Align hub ac
cess hole with retaining pin.
Turn pin until
it rel
eases
from backing plate.
5. Remove adju ster assembly.
Move front shoe forwards.
Remove adju
ster assembly.
6. Re
move rear shoe retaining pin.
Al
ign hub ac
cess hole with retaining pin.
Turn pin until
it rel
eases
from backing plate.
7. Remove brake shoes from parkin g brake lever-mechanism and
remove shoes from vehicle.
8. Remove return sp rings from shoes.