Page 2065 of 2490

2. Ensure that
gear selector is in position 'R'.
3. Inst
all gear selector cable in 'J' gate.
1. Position gear selector cable in support bracket.
2. Connect inner cable to 'J' gate stud and fit and
tighten securing nut.
4. Adjust
gear selector cable.
1. Adjust selector cable nuts so that selector lever freely
moves to 'R' position in gate.
2. Tighten gear selector ca ble locknut, ensuring that
tabwasher tangs engage in bracket slots.
5. Ensure that
gear selector cable
to tunnel grommet is correctly
seated.
6. Fit and secure handbrake trim finisher. Refer to 76.13.63.
7. Fully seat carpet side and rear retaining clips.
8. Fit front sill treadplates. Refer to operations in this section.
9. Fit rear sill treadplates. Refer to operations in this section.
10. Position and fully seat rear heel boards and rotate 1/4 turn
fasteners to secure.
11. Install console heater ducting and fit and tighten securing
screw.
12. Fit 'B' post trim pads. Refer to operations in this section.
13. Fit lower 'A' post trim pads. Refer to 76.13.30.
14. Fit centre console asse mbly. Refer to 76.25.01.
15. Fit fascia centre ve nt veneer panel. Refer to 76.47.06.
16. Fit centre console finisher vene er panel. Refer to 76.47.26.
17. Fit 'J' gate surround. Refer to 76.25.24.
18. Fit rear seat cushion. Refer to 76.70.37.
19. Fit front seats. Refer to 76.70.01.
20
.
Connect ground cable to batt ery terminal and fit battery
cover. Refer to 86.15.15.
Page 2066 of 2490
Interior Trim and Ornamentation - Folding Tray
Removal and Installation
Removal
Installation
1. Remove screws securing picnic tray hinges to seat back
finisher and remove tray from seat.
2. Remove screws securing hinges to picnic tray. and remove
hinges from tray
3. Remove clips from hinge centre securing screw positions.
4. Remove trim securing screws and remove trim from veneer
panel.
1. Position trim on veneer panel an d install trim securing screws.
Page 2067 of 2490
2.
Install clips at hinge centre securing screw positions.
3. Position hinges on veneer panel and install securing screws.
4. Position hinges on seat back finisher and install securing
screws.
Page 2068 of 2490
Interior Trim and Ornamentation - Folding Tray Finish Panel
Removal and Installation
Removal
Installation
1. Move picnic tray to fully down position.
2. Remove screws securing picnic tray hinges to back finisher
and remove tray from seat.
3. Remove the two back finisher to seat securing screws.
4. Release finisher from side mount ing clips and remove finisher
from seat.
5. Remove three screws se curing picnic tray top rail veneer panel
to seat finisher and remove veneer panel.
Page 2069 of 2490
1.
Position top rail veneer panel on finisher, locate two dowels
and install securing screws.
2. Position back finisher on seat and install lower securing screws.
3. Position and fully seat fini sher side securing clips.
4. Position picnic tray on back fi nisher and install hinge securing
screws.
5. Move picnic tray to up position.
Page 2070 of 2490
Interior Trim and Ornamentation - Front Door Armrest Removal and Installation
Removal
Installation
1.
Remove battery cover and disconnect ground cable from battery
terminal. Refer to 86.15.19.
2. Remove door casing. Refer to 76.34.01.
3. Slacken and remove four screws se curing armrest to door casing
and remove armrest from casing.
4. Remove switchpack from armrest.
1. Slacken and remove two screws securing switchpack and finisher to armrest.
2. Remove switchpack and finisher from armrest.
5. Slacken and remove two screws secu ring armrest retaining clip and
remove clip from armrest.
1. Position retaining clip on armrest and fit and tighten securing
screws.
2. Position switchpack and finisher on armrest and fit and tighten
securing screws.
3. Position armrest on casing and fit and tighten four securing screws.
4. Fit casing to door. Refer to 76.34.01.
5. Connect ground cable to battery and fit battery cover. Refer to
86.15.15.
Page 2071 of 2490
Interior Trim and Ornamentation - Front Door Trim Panel Finish Panel
Removal and Installation
Removal
Installation
1. Remove interior door handle escutcheon.
Remove cover from door ha ndle escutcheon securing
screw and slacken and remove screw.
Pull door handle inwards and exercising care to avoid
damaging tweeter, remove escutcheon from casing.
2. Remove veneer panel from casing.
1. Using a thin plastic leve r, carefully ease rear of
veneer panel inwards to release the two rear
securing tangs.
2. Slide veneer panel re arwards to release front
retainers.
1. Position veneer panel on casing and slide forward to engage
front retainers.
2. Using a soft pad or cloth, press re ar of panel firmly to seat the
securing tangs.
3. Fit door handle escutcheon.
Page 2072 of 2490
Interior Trim and Ornamentation - Front Door Stowage Compartment
Removal and Installation
Removal
Installation
1.
Remove door casing for access. Refer to 76.34.01.
2. Remove pocket from door casing.
1. Release puddle lamp harness from clips at base of door pocket.
2. Slacken and remove th e two screws securing
bottom of pocket to casing.
3. Remove two spring clips securing top of pocket to casing.
3. Lift pocket out of casing .
1. Position pocket in casing and secure with screws and spring
clips.
2. Position puddle lamp harn ess in pocket clips.
3. Fit door casing. Refer to 76.34.01.