1998 JAGUAR X308 Workshop Manual

infotainment roof coolant temperature key fob ESP inoperative automatic transmission fluid

Load previous 8 pages

Page 1497 of 2490

JAGUAR X308 1998 2.G Workshop Manual
4. Remove the ball and spring.
14. Clean all components.

15. Reassemble the shift mechanism.
1. Apply grease and install the detent ball and spring.
2. Apply grease to the pivot bracket and

Page 1498 of 2490

JAGUAR X308 1998 2.G Workshop Manual

19. Inst
all the slide plate.
Install
the four sl
ide plate screws.

20 . Fi
t the gear shift assembly.
Inst
all th
e four nuts.

21 . Asse
mble the cable to the gear shift ass

Page 1499 of 2490

JAGUAR X308 1998 2.G Workshop Manual Automatic Transmission/Transaxle External Controls - 4.0L SC V8 - AJ26 -
External Controls
Description and Operation
Introduction
Operator gearshift control is effected by:
The selector lever

Page 1500 of 2490

JAGUAR X308 1998 2.G Workshop Manual
ItemPart NumberDescription
1—Gear selector lever
2—Access blank - Gear-shift interlock solenoid
3—Connector - DLS
4—Dual Linear Switch (DLS)
5—Connector - Park position switch
6—Con

Page 1501 of 2490

JAGUAR X308 1998 2.G Workshop Manual Selector lever:
Gear selector positions are:
P Transmission mechanically locked, starting available * R Reverse gear N Neutral gear, no power to the rear wheels (starting available) D

Page 1502 of 2490

JAGUAR X308 1998 2.G Workshop Manual
The performance mode pushbutton:
Is mounted on the J gate surround. This push-on push-off swit ch selects Normal or Sport mode ( push-on for Sport) Is illuminated when Sport mode is

Page 1503 of 2490

JAGUAR X308 1998 2.G Workshop Manual Dual-Linear Switch (DLS)
The TCM detects gear selection by means of a switch fitted to the J gate; the DLS contains two multi-track slider switches,
of which the upper controls P R N D and the low

Page 1504 of 2490

JAGUAR X308 1998 2.G Workshop Manual Automatic Transmission/Transaxle External Controls - 4.0L SC V8 - AJ26 -
External Controls
Diagnosis and Testing
Problem Solving - Transmission Shift
Quick Reference Fault Chart
Special Tool(s)

Automatic Transmission/Transaxle External Controls - 4.0L SC V8 - AJ26 -
External Controls
Diagnosis and Testing
Problem Solving - Transmission Shift
Quick Reference Fault Chart
Special Tool(s)

Digital multimeter

Generic scan tool
SymptomPossible SourcesAction
Shift stuck in P Selector cable seized
*GO to 44.15.08
*
Interlock solenoid not operating
*GO to PDU
*
Interlock latch seized
Transmission faulty
*
*Mechanical check
*
Operator sequence error
*Correct the sequence
*
Vehicle rolls on P Incorrect cable adjustment
*GO 44.15.07
*
Faulty parking pawl (transmission internal)
*Mechanical check
*
R does not engageIncorrect cable adjustment
*GO to 44.15.07
*
Transmission fluid level incorrect
*GO to 44.24.02
*
N not achievedIncorrect cable adjustment
Transmission faulty
*
*GO to 44.15.07
*
D does not engageIncorrect cable adjustment *GO to 44.15.07
*
Transmission fluid level incorrect
*GO to 44.24.02
*
Transmission faulty
*Mechanical check
*
Lower ratios will not holdExcessive engine temperature
DLS fault
*
*GO to PDU
*
Shift lever position not visually correctIncorrect DLS adjustment
*GO to 44.15.07
*
Shift lever has no effect upon the
transmission and resistance cannot be
feltCable disconnected or broken
Transmission selector problem
Shift lever drive pin adrift
*
*
*Mechanical check
*
Shift lever position not align correctly
following manual selection of lower
ratiosSliding block drive pin displaced - following road debris contact
*Mechanical check. Renew the selector if
damaged, or re-align the drive pin and
sliding block
*
Shift lever detent indistinct in 3
causing poor locationDLS detent fault
*GO to Renew the DLS
*
Shift may be moved from P without
brake pedal operationInterlock latch fault
*Mechanical check
*
Solenoid permanently activated
*GO to PDU
*
Engine may be started in positions
other than P or N Incorrect cable adjustment
DLS fault
*
*GO to 44.15.07
*
Shift lever vibrationLoose selector assembly
Cable isolation fault
*
*Mechanical check
*
Noise / rattle from 'J' gateDebris in the mechanism
*Clean
*
Worn 'J' gate track gasket
allowing lever and moulding to
contact
*GO to 44.15.05
*

Load next 8 pages

Page: < prev 1-10 ... 1465-1472 1473-1480 1481-1488 1489-1496 1497-1504 1505-1512 1513-1520 1521-1528 1529-1536 ... 2496 next >

instrument cluster radio auxiliary battery location immobilizer oil filter brake pads