Page 2081 of 2490
Interior Trim and Ornamentation - Luggage Compartment Lid Trim Panel
Removal and Installation
Removal
Installation
1. Remove trunk lamp assemblies. Refer to 86.45.16.
2. Release the three warning triang le securing clips and remove
warning triangle.
3. Slacken and remove warning triangle mounting bracket
securing screws an d remove bracket.
4. Remove covers from trunk latc h finisher securing bolts,
slacken and remove bolts and remove finisher.
5. Remove and discard the eighteee n trunk lid liner fasteners and
remove liner from vehicle.
Page 2082 of 2490
1.
Position liner on trunk lid and pass lamp harness multiplugs
through apertures.
2. Align and fully seat liner on trunk lid and secure with new
fasteners.
3. Position finisher over trunk lid latch, fit and tighten securing
bolts and fit bolt covers..
4. Position warning triangle mounti ng bracket and fit and tighten
securing screws.
5. Install triangle on mounting br acket and secure with clips.
6. Install trunk lamp assemblies. Refer to 86.45.16.
Page 2083 of 2490
Interior Trim and Ornamentation - Luggage Compartment Rear Trim Panel
Removal and Installation
Removal
Installation
1. Remove tail lamp covers.
2. Remove trunk floor and battery cover. Refer to operations in
this section.
3. Remove and discard the two fir tr ee fasteners securing finisher
to trunk rear panel.
4. Pull rear finisher upwards to release upper spring clips and
remove finisher from trunk.
1. Position finisher on trunk rear panel and press firmly
downwards to engage spring clips.
2. Fit and fully seat fir tree fasteners.
3. Fit trunk floor and battery cover. Refer to operations in this
section.
4. Fit tail lamp covers.
Page 2084 of 2490
Interior Trim and Ornamentation - Luggage Compartment Side Trim Panel
Removal and Installation
Removal
Installation
1.
Remove trunk floor carpet.
2. Remove trunk front liner. Refer to 76.19.31.
3. Remove trunk rear finisher. Refer to 76.19.44.
4. Remove literature pack from tr unk side liner (RH side only).
5. Remove side liner from trunk.
1. Position and fully seat side liner in trunk.
2. Install literature pack on side liner (RH side only).
3. Fit trunk rear finisher.Refer to 76.19.44.
4. Fit trunk front liner. Refer to 76.19.31.
5. Fit trunk floor carpet.
Page 2085 of 2490
Interior Trim and Ornamentation - Overhead Console Finish Panel
Removal and Installation
Removal
Installation
1.
Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Remove roof console. Refer to 76.13.69.90.
3. Bend back veneer panel retain ing tangs from console and using a thin blade, carefully release panel from console.
1. Remove backing paper and apply adhesive pad to back of
panel.
2. Position and fully seat ve neer panel on console.
3. Bend retaining tangs to secure veneer panel to console.
4. Install roof console. Refer to 76.13.69.90.
5. Connect ground cable to batter y terminal and install battery
cover. Refer to 86.15.15.
Page 2086 of 2490
Interior Trim and Ornamentation - Parcel Shelf
Removal and Installation
Removal
Installation
1.
Open both rear doors.
2. Remove rear seat cushion. Refer to 76.70.37.
3. Remove rear seat squa b. Refer to 76.70.38.
4. Remove and discard the two fir tr ee fasteners securing front of
tray to parcel shelf.
5. Remove parcel tray.
Slightly raise front of shelf trim and lift rear fold clear of
body flange.
Exercising care to avoid dama ging sun blind (if fitted) and
rear quarter trims, or dislodging high level stop lamp, slide trim from shelf, twist slightly and remove from vehicle via
rear doors.
1. Exercising care to avoid damaging sun blind (if fitted) and rear
quarter trims, or dislodging hi gh level stop lamp, slide trim
onto shelf, engaging rear fold on body flange.
2. Secure front of trim to shelf using two new fir tr ee fasteners.
3. Fit rear seat squab. Refer to 76.70.38.
4. Fit rear seat cushion. Refer to 76.70.37.
Page 2087 of 2490
Interior Trim and Ornamentation - Parcel Shelf Support
Removal and Installation
Removal
Installation
1.
Remove rear parcel tray. Refer to 76.67.06.90
2. Place parcel tray face down on clean bench.
3. Where sun blinds are fitted:
1. Slacken and remove nuts securing sun blind to parcel tray.
2. Remove washers.
3. Remove sun blind from parcel tray.
4. Remove eight clips securing parc el tray outer panel to inner
panel and separate panels.
1. Align outer panel to inner panel
2. Secure panels together with eight clips.
3. Where sun blinds are to be fitted, position rollers on underside
of parcel tray, fit washers and fit and tighten nuts to 5-7Nm.
4. Fit parcel tray. Refer to 76.67.06.90.
Page 2088 of 2490
Interior Trim and Ornamentation - Passenger Assist Handle
Removal and Installation
Removal
Installation
1. Using a piece of wood or simila rly soft material, press inner
end of each screw cover to release outer clip.
2. Remove screw covers , slacken and remove securing screws
and remove grab handle from cantrail.
1. Position grab handle and coat hanger hook at cantrail
2. Ensuring that cantrail trim pads are correctly aligned, fit and
tighten the grab handle securing screws.
3. Slide each screw cover inner end foremost, onto end of grab
handle and press outer end to engage clip.