1998 JAGUAR X308 wiring

                    Knock Sensor  (KS)  RH  (18.30.93)  
                    
Variable Camshaft  Timing  (VCT)  Oil  Co ntrol
 
Solenoid  (18.30.90)  
 
        
307:  Automatic  Transmission/Transaxle  
 
             307‐01A : Automatic  Transmission/Transaxle  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                 Specification  
                 Description  and  Operation  
                     Transmission  Description 
                 Diagnosis  and  Testing  
                     Diagnostic Strategy  
                 General Procedures  
                     Transmission  Fluid Drain  and  Refill  (44.24.02)  
                 In‐Ve
hicle  Repair  
                     Electronic Pressure  Control (EPC)  Solenoid  (44.15.51)  
                     Extension Housing  Seal  (44.20.18)  
                     Extension Housing  O ‐Ring  Seal  (44.20.19)  
                     Main Control  Valve Body  (44.40.01)  
                     Output Shaft  Speed  (OSS)  Sensor  (44.15.41)  
                     Shift Solenoids  (SS)  (44.15.50)  
                     Transmission  Control Module  (TCM)  (44.15.32)  
                     Transmission  Fluid Filter  (44.24.07)  
                     Transmission  Fl
uid  Pan  (44.24.04)  
                     Transmission  Fluid Pan  Gasket  (44.24.05)  
                     Transmission  Internal Wiring  Harness  (44.15.35)  
                     Transmission  Internal Wiring  Harness  Electrical  Connector  O‐Ring  Seals  
            (44.24.20) 
                     Transmission  Range (TR)  Sensor  
                     Transmission  Support Insulator  (12.45.04)  
                     Turbine Shaft  Speed  (TSS)  Sensor  (44.15.40)  
                 Removal 
                     Transmission  (44.20.01) 
                 Disassembly  and  Assembly  of Subassemblies  
                     Input Sh
aft  Seal  (44.32.07)  
                     Torque Converter  (44.17.07)  
                 Installation  
                     Transmission  (44.20.01) 
Mass
 
Airflow
 
Sen s
or
 
Knock
 Sensor
 (KS)
 LH
 (18.30.92)
 

 
            307‐01B : A u
tomatic
 Transmission/Transaxle  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Specification  
                 Description  and  Operation  
                     Transmission  Description 
                 Diagnosis  and  Testing  
                     Diagnostic Strategy  
                 General Procedures  
                     Transmission  Fluid Drain  and  Refill  (44.24.02)  
                 In‐Vehicle  Repair  
                     Extension Housing  Seal  (44.20.18)  
                     Main Control  Valve Body  (44.40.01)  
                     Transmission  Fluid Filter  (44.24.07)  
                     Transmission  Fl
uid  Pan  Gasket  (44.24.05)  
                     Transmission  Internal Wiring  Harness  Electrical  Connector  O‐Ring  Seals  
            (44.24.20) 
                     Transmission  Support Insulator  (12.45.04)  
                 Removal 
                     Transmission  (44.20.01) 
                 Disassembly  and  Assembly  of Subassemblies  
                     Input Shaft  Seal  (44.32.07)  
                     Torque Converter  (44.17.07)  
                 Installation  
                     Transmission  (44.20.01) 
 
             307‐02A : Transmission/Transaxle  Cooling  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ
27  
                 Description  and  Operation  
                     Transmission  Cooling 
 
             307‐02B : Transmission/Transaxle  Cooling  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Description  and  Operation  
                     Transmission  Cooling 
 
             307‐05A : Automatic  Transmission/Transaxle  External  Controls  ‐ 3.2L  NA  V8  –  
            AJ26/4.0L NA  V8  ‐ AJ27  
                 Description  and  Operation  
                     External Controls  

                    Side Turn  Signal  Lamp  (86.41.41)  
                     Side Turn  Signal  Lamp  Bulb  (86. 41.42)  
 
             417‐02
:
 Interior  Lighting  
                 Specification  
                 Description  and  Operation  
                     Interior Lighting  
                 Diagnosis  and  Testing  
                     Interior Lighting  
                 Removal and  Installation  
                     Door Courtesy  Lamp (86.40.38)  
                     Door Courtesy  Lamp Bulb  (86.40.47)  
                     Door Courtesy  Lamp Lens  (86.40.35)  
                     Glove Co
mpartment  Lamp  (86.45.08)  
                     Luggage Compartment  Lamp (86.45.16)  
                     Vanity Mirror  Lamp  (76.10.50)  
 
             417‐04:  Daytime  Running  Lamps  (DRL) 
                 Description  and  Operation  
                     Daytime Running Lamps  (DRL) 
                 Diagnosis  and  Testing  
                     Daytime Running Lamps  (DRL) 
 
        418:  Electrical  Distribution  
 
             418‐00:  Module  Communications  Network  
                 Description  and  Operation  
                     Communications  Ne
twork 
                                                      Removal
 and  Installation  
                     Battery
 Junction  Box  (BJB)  (86.70.69)  
                     Central
 Junction  Box (CJB)  (86.70.72)  
                     Front
 Auxiliary  Junction  Box  (86.70.73)  
                     Rear
 Auxiliary  Junction  Box  (86.70.74)  
 
  
418 ‐02:  Wiring  Harnesses  
Description  and  Operati
on
 
Wiring  Harness  
General  Procedures  
Wiring  Harness  Repair 

Vehicle Dynamic Suspension - Vehicle Dynamic Suspension
Diagn
osis and Testing
Refer to the PDU User Guide for details of diagnosing and testing the Adaptive Damping System. The PDU interrogates the
ADCM directly via the K and L lines to the J1962 diagnostic socket.
The PDU will give an indication of the integrity of each electron ic and electrical component. It will indicate, for example, that
the accelerometers are not broken, but not that they functionin g correctly when the vehicle is in motion. However, it is
exceptional for an accelero meter to function incorrectly in its dynamic mode if it is proved to be functioning when static.
Basic Checks
The accele
rometers have the following ch
aracteristics. At 0g (no movement of the body) each vertical accelerometer
outputs approximately 2.5V steady voltage; the lateral acce lerometer outputs approximately 1.5V. The voltage output due
to body movement is proportional to acceleration in the acceleration axis, up to approximately 4.5V and down to
approximately 0.5V.
Before changing any component, refer to the circuit diagrams and check the cont inuity of relevant harness circuits; in some
instances, the PDU will not different iate between a faulty component an d a damaged connection or wiring.
Check the following fuses:
En
gine compartment fuse
box, fuse F5 (10A).
Engine m
anagement fuse
box, fuse F1 (20A).
Check the following ADCM input/output lines:
Sy stem erro
r output from the ADCM
to the instrument cluster.
Vehicl
e speed output from the inst
rument cluster to the ADCM.
Foo
tbrake signal to the ADCM.
Check any relevant connections to confirm that the connection is electrically sound and that a terminal pin has not been
pushed back into the connector shell, ie. not ma king a connection to its mating pin or socket.

Brake System - General Inform
ation - Brake System
D
iagnosis and Testing
Principles of Operations
The brake system operates by transferring effort applied to th e brake pedal, by the driver to the brakes at each wheel.
The braking effort is distributed to each wheel, using a hydraulic system. The system is assisted using a vacuum brake
booster that reduces pedal effort for a given hydraulic pressure. The parking brake operates on the rear wheels and is
applied using a hand operated control.
I
nspection and Verification
•
NOTE: Prior to carrying out any diagno
sis, make sure that the brake system warning indicator is functional.
Visually examine the front and rear tire and wheel assemblies for damage such as un even wear patterns, tread worn out or
sidewall damage. Verify the tires are th e same size, type and, where possible, same manufacture. Replace the damaged
wheel or excessively worn tire. For a dditional information, refer toSection 204
-0
4 Wheels and Tires
.
W
heels and tires must be cleared of an
y foreign matter and tire pressures ad justed to the correct specification.
If the tires exhibit uneven wear or feathering, the cause must be corrected. Check the steering and suspension components
for damage or wear and, if ne cessary, check and adjust front wheel alignment. For additional information, refer toSection
204
-00 Suspen
sion System
- General Informati
on
.
Road Test


V
isual Inspection Chart
Carr

y out a road test to compare actual vehicle braking performance with the
performance standards expected by the
driver. The ability of the test driver to make valid compar isons and detect performance deficiencies will depend on
experience.
The driver should have a thorough knowledge of brake system operation and accepted general performance guidelines to
make good comparisons and de tect performance concerns.
An experienced brake technician will always establish a route that will be used for all br ake diagnosis road tests. The roads
selected will be reasonably smooth and level. Gravel or bump y roads are not suitable because the surface does not allow the
tires to grip the road equally. Crowned roads should be avoide d because of the large amount of weight shifted to the low set
of wheels on this type of road. Once th e route is established and consistently used, the road surface variable can be
eliminated from the test results.
Before a road test, obtain a complete description of the customer concerns or suspec ted condition. From the description, the
technician's experience will allow the te chnician to match possible causes with symptoms. Certain components will be
tagged as possible suspects while others wi ll be eliminated by the evidence. More importantly, the customer description can
reveal unsafe conditions which should be ch ecked or corrected before the road test. The description will also help form the
basic approach to the road test by narrowing the concern to specific components, vehicle speed or conditions.
Begin the road test with a general brake performance check. Keeping the description of the concern in mind, test the brakes
at different vehicle speeds using both ligh t and heavy pedal pressure. To determine if the concern is in the front or rear
braking system, use the brake pe dal and then use the parking brake control. If the condition (pull, vibration, pulsation)
MechanicalElectrical
Brake m
aster cylinder
Parkin
g brake switch
Brake ca

liper piston(s)
D
amaged or corroded wiring harness
Brake di

scs
B
rake master cylinder fluid level switch
Wh

eel bearin
gs
Brake pads
Power brake booster
Brake ped

al linkage
Boost

er vacuum hose
Tire

s
De

bris

sus
pension components
and for damaged coil springs in the front suspension.
as necessary. For addi tional information,
REF
ER to Section 204
-0
2 Rear Suspension
. I

NSTALL new front suspension components
as necessary. For addi tional information,
REFER to Section 204
-01
Front Suspension
.
Chec

k the rear suspension

for loose or worn
suspension components.
TIGHTE
N or INSTALL new components as
necessary. For additi onal information,
REFER to Section 204
-0
2 Rear Suspension
.
Incorre

ct underbody
alignment.
CHECK
underbody alignment. For additional

information,
REFER to Section 502
-00
Uni
-Body, Subframe and M

ounting System
.
Poor r

eturnability of the
steering
Lower steeri
ng column
interference.
CHECK
the steering co
lumn is free from
interference from the en gine harness, sound
proofing or the floor covering.
Incorrect
tire pressure.
CHECK
and ADJUST the tire pressure. For
additional information,
REFER to Section 204
-0
4 Wheels and Tires
.
Incorrect

tire size or type.
IN
STALL a new tire as necessary. For
additional information,
REFER to Section 204
-0
4 Wheels and Tires
.
Steeri

ng column upper
shroud fouling on the steering wheel.
CHECK
steering column upper shroud for
fouling. ADJUST as necessary.
Steeri
ng column universal
joints binding.
IN
STALL a new steering column. For
additional information,
REFER to Section 211
-0
4 Steering Column
.
Steeri

ng column shaft floor

seal binding.
CHE
CK the steering column shaft floor seal
for correct fitm ent and REFIT as necessary.
Steeri
ng column shaft floor

seal may be torn.
IN
STALL a new steering column shaft floor
seal as necessary.
Bin
ding or damaged tie-
rods.
CHECK
tie-rod end for excessive wear or
tightness in ball joint. INSTALL a new tie- rod end. For additional information,
REFER to Section 211
-0
3 Steering Linkage
.
D

amaged or worn front
suspension components.
I
NSTALL new front suspension components
as necessary. For addi tional information,
REFER to Section 204
-01
Front Suspension
.
Incorre

ct toe adjustment.

AD
JUST as necessary. For additional
information,
REFER to Section 204
-00
Suspension
Sy

stem
- General
Information
.
Excessive steeri

ng efforts
required during low speed
manoeuvring and/or during parking manoeuvres
Low power steer
ing fluid.

CHE
CK steering system
for signs of steering
fluid loss.
BLEE
D the power steering system. For
additional information,
REFER to Section 211
-0
0 Steering System
- General Informati

on
.
Damaged accessory driv

e
belt tensioner.
INST
ALL a new accessory drive belt
tensioner.
Hose or cooler li
ne
restriction.
CHECK
hose or cooler lines for correct
routing.
INST
ALL a new hose as necessary.
Fl

uid aeration.
BLEE
D the system. For additional
information,
REFER to Power Steering System Bleeding

in t
his section.

Steeri
ng transducer not
closed - no feed voltage.
CHECK
the steering transducer circuit. For
additional information, REFER to the wiring diagrams.
Carry ou
t the electrical checks and tests.
For additional information, REFER to the
Electrical Checks and Tests in this section.
Steeri
ng transducer not
closed - cable fault.
CHECK
the steering transducer circuit. For
additional information, REFER to the wiring diagrams.
Carry ou
t the electrical checks and tests.

Fo
r additional information, REFER to the
Electrical Checks and Tests in this section.
Steering control
module
(SCM) defective.
CHECK
the SCM and INSTALL a new SCM as

necessary.
Power steeri ng f
luid
delivery pressure or flow too low.
CHECK
the power stee
ring pressure. For
additional information, REFER to the Power Steering Pressure Test in this section.
INSTALL a ne
w power steering pump as
necessary. For additi onal information,
REFER to Section 211
-0 2
Power Steering
.
Internal steering gear
leakage.
CHECK
the power stee
ring pressure. For
additional information, REFER to the Power Steering Pressure Test in this section.
INSTALL a ne
w steering
gear as necessary.
For additional information,
REFER to Section 211
-0 2
Power Steering
.
Steeri
ng operati
on is very
heavy when driving, but when stationary
manoeuvring is good
Steering transducer open earl
y.
CHECK

steering transducer and INSTALL a
new steering transducer as necessary.
Carry out th
e electrical checks and tests.
For additional information, REFER to the
Electrical Checks and Tests in this section.
Steering transducer open
early,
steering control
module (SCM) fault.
CHECK
SCM and INSTALL a new SCM as
necessary.
Steering transducer open
earl
y, speedo signal error.
CHECK
speedo
circui
t. For additional
information, REFER to the wiring diagrams.

Steeri ng operati
on is very
light when driving, but when
stationary manoeuvring is good
Steering transducer not
o
pen, (no power steering
fluid flow).
CHECK
the power steering fluid condition.
For additional information, REFER to the
Power Steering Fluid condition check in this section.
Steering transducer not o
pen, steering control
module (SCM) fault.
CHECK
the SCM and INSTALL a new SCM as

necessary.
Carry out th
e electrical checks and tests.
For additional information, REFER to the
Electrical Checks and Tests in this section.
Steering transducer not
o
pen, speedo signal error.
CHECK

the speedo circ
uit. For additional
information, REFER to the wiring diagrams.

CHECK
the power steering
fluid low pressure pipe for restricted flow.
INSTALL a ne
w power steering fluid low
pressure pipe.
S t
eering heavy operation
during rapid manoeuvring
Ai r i
n power steering
system.
CHECK for an air l
eak into the power
steering system and re pair as necessary.
BLEED the
power steering system. For
additional information,
REFER to Power Steering System Bleeding
- in t hi
s section.
Fluid loss at the power
steering pump shaft seal.
CHECK the power steer
ing pump for signs o
f steering fl
ui
d loss.
INST
ALL a ne
w power steering pump as
necessary. For additi onal information,
REFER to Section 211
-0 2
Power Steering
.
Power steeri
ng f
luid
delivery pressure or flow too low.
CHECK the power steer
ing pump for signs o
f steering fl
ui
d loss.
CHECK

the power stee
ring pressure. For
additional information, REFER to the Power Steering Pressure Test in this section.
INSTALL a ne
w power steering pump as
necessary. For additi onal information,
REFER to Section 211
-02
Power Steering
.
Lower steeri
ng col
umn
interference.
CHECK
the steering co
lumn is free from
interference from the en gine harness, sound
proofing or the floor covering.
Incorrect steering geometry. CHE
CK the front wheel alignment. For
additional information,
REFER to Section 204
-00 Sus
pension
Sy
ste
m
- General

Information
.
CHECK

the power stee
ring pressure. For

No
ise
S
teering heavy operation in
one direction
F
aulty rotary valve/seal.
addi
tional information, REFER to the Power
Steering Pressure Test in this section.
INST
ALL a new steering
gear as necessary.
For additional information,
REFER to Section 211
-0
2 Power Steering
.
Ti

re fouling on the wheel
arch liner.
CHECK for
clearance be
tween the tire and
the wheel arch liner.
R
emove and refit the wheel arch liner or
INSTALL a new wheel arch liner as necessary.
S
teering heavy operation in
both directions
Low power steer
ing fluid.

CHE
CK steering system
for signs of steering
fluid loss.
BLEE
D the power steering system. For
additional information,
REFER to Section 211
-0
0 Steering System
- General Informati

on
.
Ai

r in power steering
system.
CHECK
the power steering pump for signs o
f steering fl

uid loss.
INST

ALL a new power steering pump as
necessary. For additi onal information,
REFER to Section 211
-0
2 Power Steering
.
Fluid loss at the power
steering pump shaft seal.
CHECK
the power steering pump for signs o
f steering fl

uid loss.
INST

ALL a new power steering pump as
necessary. For additi onal information,
REFER to Section 211
-0
2 Power Steering
.
Power steeri

ng fluid
delivery pressure or flow too low.
CHECK
the power steering pump for signs o
f steering fl

uid loss.
CHECK

the power stee
ring pressure. For
additional information, REFER to the Power Steering Pressure Test in this section.
INST
ALL a new power steering pump as
necessary. For additi onal information,
REFER to Section 211
-0
2 Power Steering
.
Steeri

ng operation varies
from heavy to light when
driving at constant speed
Lower steeri
ng column
interference.
CHECK
the steering co
lumn is free from
interference from the en gine harness, sound
proofing or the floor covering.
Incorre
ct sp
eedometer
signal.
CHECK
the speedo circ
uit. For additional
information, refer to the wiring diagrams.
Steeri
ng transducer
cable/connection faulty or grounded.
CHECK
the steering transducer circuit. For
additional information, refer to the wiring diagrams.
Carry ou
t the electrical checks and tests.
For additional information, REFER to the
Electrical Checks and Tests in this section.
Steeri
ng wheel varies from
light to heavy two times per revolution
Lower steeri
ng column
interference.
CHECK
the steering co
lumn is free from
interference from the en gine harness, sound
proofing or the floor covering.
Steeri
ng column universal
joints binding.
IN
STALL a new steering column. For
additional information,
REFER to Section 211
-0
4 Steering Column
.
Seized or damaged
ste
ering components.
CHECK
for wear or failure of suspension
bushes and ball join ts. For additional
information,
REFER to Section 204
-00
Suspension
Sy

stem
- General
Information
.
Cond

ition
Possib
le Sources
Acti
on
Acce

ssory drive
belt squeal
Incorre
ct accessory drive belt

tension or accessory drive belt glazed.
CHECK
accessory drive belt condition and INSTALL a
new accessory drive belt as necessary. For additional
information,
REFER to Section 303
-0
5 Accessory Drive
.
Chir

p noise in
the steering pump
Loose or worn accessory dr
ive belt.
CHECK
accessory drive belt condition and INSTALL a
new accessory drive belt as necessary. For additional
information,
REFER to Section 303
-0
5 Accessory Drive
.