Page 1025 of 2248

G5M0341
3) Position seat in compartment and align the holes on the
seat with the holes on the vehicle body side.
4) Secure the front of seat using inward and outward bolts
1and2in that order.
5) While pulling slide adjuster lever, move seat all the way
forward.
6) Secure the rear of seat using inward and outward bolts
3and4in that order.
7) Install bolt
5.
8) Connect connector under driver’s seat.
CAUTION:
Check that all lock plate pawls are completely and
equally inserted into the holes in the slide rail brack-
ets.
9) After installation, ensure that all mechanisms operate
properly and lock.
10) If any mechanism does not function properly, loosen
bolts
3,4and5, slide seat as required, insert all lock
plate pawls into holes in slide rail brackets, and tighten
bolts
3,4and5in that order.
11) Install bolt cover on rear end of slide rail.
12) Install headrest on backrest.
NOTE:
Tighten bolts in the designated order.
G5M0345
2. Rear Seat
A: REMOVAL
1. SEDAN MODEL
1) Remove bolts securing hinges (located at front of cush-
ion) to body.
2) Slightly raise front of cushion while pushing down on
cushion in the direction of“C”. With cushion held in that
position, move it forward until it is unhooked.
G5M0346
3) Remove bolts securing lower portion of backrest to
body.
4) Pull strap (located in center of fold-down backrest) to
release lock, and fold backrest onto cushion. (Fold-down
type)
5) Lift rear seat backrest in direction“A”until it is released
from upper hooks.
9
5-3SERVICE PROCEDURE
1. Front seat - 2. Rear Seat
Page 1026 of 2248

G5M0341
3) Position seat in compartment and align the holes on the
seat with the holes on the vehicle body side.
4) Secure the front of seat using inward and outward bolts
1and2in that order.
5) While pulling slide adjuster lever, move seat all the way
forward.
6) Secure the rear of seat using inward and outward bolts
3and4in that order.
7) Install bolt
5.
8) Connect connector under driver’s seat.
CAUTION:
Check that all lock plate pawls are completely and
equally inserted into the holes in the slide rail brack-
ets.
9) After installation, ensure that all mechanisms operate
properly and lock.
10) If any mechanism does not function properly, loosen
bolts
3,4and5, slide seat as required, insert all lock
plate pawls into holes in slide rail brackets, and tighten
bolts
3,4and5in that order.
11) Install bolt cover on rear end of slide rail.
12) Install headrest on backrest.
NOTE:
Tighten bolts in the designated order.
G5M0345
2. Rear Seat
A: REMOVAL
1. SEDAN MODEL
1) Remove bolts securing hinges (located at front of cush-
ion) to body.
2) Slightly raise front of cushion while pushing down on
cushion in the direction of“C”. With cushion held in that
position, move it forward until it is unhooked.
G5M0346
3) Remove bolts securing lower portion of backrest to
body.
4) Pull strap (located in center of fold-down backrest) to
release lock, and fold backrest onto cushion. (Fold-down
type)
5) Lift rear seat backrest in direction“A”until it is released
from upper hooks.
9
5-3SERVICE PROCEDURE
1. Front seat - 2. Rear Seat
Page 1027 of 2248

G5M0350
2. WAGON MODEL
1) Remove bolts securing hinges (located at front of seat)
to body.
2) Pull strap (located in middle rear portion of cushion) to
release lock. Lift cushion out and away from body.
3) Pull knobs (located at each side of backrest’s upper
portion) up to release lock, and fold backrest all the way
forward.
B5M0333A
4) Remove the bolt1and then remove backrest. (LH
side)
5) Remove the bolt
2and then remove backrest (RH side)
from hinge bracket
3.
G5M0348
G5M0345
B: INSTALLATION
1. SEDAN MODEL
1) Before installing backrest, ensure that trim panel, insu-
lator and seat belt are properly installed.
2) Transfer outer seat belt webbing to front of backrest and
fold backrest forward. Attach seat wire to upper hooks (2
places), and move pillow in the direction of“B”until back-
rest is aligned with lower mounting holes in body.
3) Engage backrest’s folding mechanism with striker.
4) Secure lower center and both sides of backrest to body
with bolts.
5) Slightly raise front section of cushion while pushing
down on cushion in the direction of“C”. With cushion held
in that position, attach rear section of cushion to hooks at
lower frame location.
6) Secure front of cushion to body with bolts.
CAUTION:
Before installing seat, ensure that seat belt is placed
on cushion.
Confirm that winding of three-point type seat belt
can operate regularly.
10
5-3SERVICE PROCEDURE
2. Rear Seat
Page 1028 of 2248

2. WAGON MODEL
Installation is in the reverse order of removal.
CAUTION:
Do not allow center seat belt to get under cushion
when folding cushion.
Ensure that side seat belt tongue is free from cush-
ion and trim panel.
Lift front of cushion to ensure that cushion is prop-
erly locked.
B5M0038A
3. Front Seat Belt
A: REMOVAL AND INSTALLATION
1. OUTER BELT
1) Remove through anchor cover cap.
2) Remove shoulder anchor bolt.
3) Remove side sill rear upper cover and front pillar lower
trim.
4) Remove center pillar lower trim.
B5M0039
5) Remove webbing guide.
6) Roll up floor mat at the bottom of center pillar.
7) Remove lap anchor bolt.
8) Remove outer belt assembly.
G5M0356
2. INNER BELT
Remove anchor nut.
G5M0357
3. ADJUSTABLE SHOULDER ANCHOR
1) Remove shoulder anchor bolt.
2) Remove lower center pillar trim.
3) Remove front and center pillar upper trim.
4) Remove adjustable shoulder anchor assembly.
5) Installation is in the reverse order of removal.
CAUTION:
The left and right ELR’s are not mutually inter-
changeable because different sensors are used.
Be careful not to twist belts during installation.
11
5-3SERVICE PROCEDURE
2. Rear Seat - 3. Front Seat Belt
Page 1029 of 2248

2. WAGON MODEL
Installation is in the reverse order of removal.
CAUTION:
Do not allow center seat belt to get under cushion
when folding cushion.
Ensure that side seat belt tongue is free from cush-
ion and trim panel.
Lift front of cushion to ensure that cushion is prop-
erly locked.
B5M0038A
3. Front Seat Belt
A: REMOVAL AND INSTALLATION
1. OUTER BELT
1) Remove through anchor cover cap.
2) Remove shoulder anchor bolt.
3) Remove side sill rear upper cover and front pillar lower
trim.
4) Remove center pillar lower trim.
B5M0039
5) Remove webbing guide.
6) Roll up floor mat at the bottom of center pillar.
7) Remove lap anchor bolt.
8) Remove outer belt assembly.
G5M0356
2. INNER BELT
Remove anchor nut.
G5M0357
3. ADJUSTABLE SHOULDER ANCHOR
1) Remove shoulder anchor bolt.
2) Remove lower center pillar trim.
3) Remove front and center pillar upper trim.
4) Remove adjustable shoulder anchor assembly.
5) Installation is in the reverse order of removal.
CAUTION:
The left and right ELR’s are not mutually inter-
changeable because different sensors are used.
Be careful not to twist belts during installation.
11
5-3SERVICE PROCEDURE
2. Rear Seat - 3. Front Seat Belt
Page 1030 of 2248
G5M0358
4. Rear Seat Belt
A: REMOVAL AND INSTALLATION
1. SEDAN MODEL
1) Remove rear cushion from vehicle.
2) Remove rear backrest from vehicle.
3) Remove rear pillar upper trim.
4) Remove outer anchor bolts.
B5M0040
5) Remove ELR.
G5M0360
6) Remove anchor bolt of outer belt and then remove outer
belt assembly.
7) Remove inner belt.
8) Installation is in the reverse order of removal.
B5M0041
2. WAGON MODEL
1) Raise rear cushion.
2) Remove shoulder anchor bolt.
3) Remove cap strut.
4) Remove rear quarter upper front trim.
G5M0362
5) Remove ELR assembly.
CAUTION:
Remove outer seat belt and center seat belt in similar
manner used to remove those from Sedan model.
12
5-3SERVICE PROCEDURE
4. Rear Seat Belt
Page 1031 of 2248
B5M0042
6) Remove lap anchor cover and then remove lower
anchor bolt.
7) Remove outer belt assembly.
8) Installation is in the reverse order of removal. Ensure
that seat belt is properly reeled on and off after installation
of ELR.
CAUTION:
Be extremely careful not to confuse center seat
anchor plate with outer seat anchor plate during instal-
lation.
Ensure that seat belts are free from twisting after
installation.
Ensure that tongues, buckles and belts are properly
placed on seat.
B5M0046A
5. Inner Trim Panel
A: REMOVAL AND INSTALLATION
1. SIDE SILL COVER
1) Remove front pillar lower trim
1.
2) Remove side sill rear upper cover trim
2.
B5M0047
2. CENTER PILLAR LOWER
Remove center pillar lower trim.
13
5-3SERVICE PROCEDURE
4. Rear Seat Belt - 5. Inner Trim Panel
Page 1032 of 2248
B5M0042
6) Remove lap anchor cover and then remove lower
anchor bolt.
7) Remove outer belt assembly.
8) Installation is in the reverse order of removal. Ensure
that seat belt is properly reeled on and off after installation
of ELR.
CAUTION:
Be extremely careful not to confuse center seat
anchor plate with outer seat anchor plate during instal-
lation.
Ensure that seat belts are free from twisting after
installation.
Ensure that tongues, buckles and belts are properly
placed on seat.
B5M0046A
5. Inner Trim Panel
A: REMOVAL AND INSTALLATION
1. SIDE SILL COVER
1) Remove front pillar lower trim
1.
2) Remove side sill rear upper cover trim
2.
B5M0047
2. CENTER PILLAR LOWER
Remove center pillar lower trim.
13
5-3SERVICE PROCEDURE
4. Rear Seat Belt - 5. Inner Trim Panel