1999 TOYOTA CAMRY Service Repair Manual

maintenance schedule remove seats reset infotainment system change key battery automatic transmission reset

Load previous 8 pages

Page 3281 of 4592

TOYOTA CAMRY 1999 Service Repair Manual SS09Q±01
± SERVICE SPECIFICATIONSCLUTCH
SS±43
206 Author: Date:
CLUTCH
SERVICE DATA
Pedal height from asphalt sheet 1MZ±FE161.8 ± 171.8 mm (6.370 ± 6.764 in.)
Pedal height from asphalt sheet 5

Page 3282 of 4592

TOYOTA CAMRY 1999 Service Repair Manual SS09R±01
SS±44
± SERVICE SPECIFICATIONSCLUTCH
207 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Master cylinder installation nut121209
Clutch line1515511
Release cylinder in

Page 3283 of 4592

TOYOTA CAMRY 1999 Service Repair Manual SS09O±01
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
SS±45
208 Author: Date:
MANUAL TRANSAXLE (E153)
SERVICE DATA
Input shaft
3rd & 4th gears journal diameterMin.
5th gear journal diamete

Page 3284 of 4592

TOYOTA CAMRY 1999 Service Repair Manual SS±46
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
209 Author: Date:
Input shaft snap ring thickness Mark
No.3 clutch hub a
b
c
d
e
f
g
h
j
Ball bearing 1
2
3
4
5
6
7
8
1.75 mm (0.0689 in.)

Page 3285 of 4592

TOYOTA CAMRY 1999 Service Repair Manual ± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
SS±47
210 Author: Date:
Output shaft bearing preload (at starting)
New bearing
Reused bearing
0.8 ± 1.6 N´m (8 ± 16 kgf´cm, 6.9 ± 13.9 in.�

Page 3286 of 4592

TOYOTA CAMRY 1999 Service Repair Manual SS09P±01
SS±48
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
211 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head A
(See page MX±4)

SS09P±01
SS±48
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
211 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head A
(See page MX±4) 14 mm head B64
46
37650
470
38047
34
27
Cruise control actuator x Body (w/ Cruise control)131309
Starter x Transaxle3940029
Clutch release cylinder x Transaxle121209
Clutch acummulator x Transaxle Bolt
Nut21
26210
27015
20
Clutch line bracket x Transaxle121209
Front wheel1031,05076
Exhaust pipe support stay3333024
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe5657041
No.1 exhaust pipe support bracket x Front suspension member3333024
Stabilizer bar link x Stabilizer bar3940029
Stabilizer bar bracket x Front suspension member1919514
PS gear assembly x Front suspension member1811,850134
Front engine absorber x Transaxle4849035
RH exhaust manifold stay2020014
Front engine mounting insulator x Front suspension member Silver bolt
Green bolt44
66450
67033
48
LH engine mounting insulator x Front suspension member8082059
LH engine mounting bracket x Transaxle6465047
Rear engine mounting insulator x Front suspension member6667048
Steering return pipe x Front suspension member101007
Front suspension member with lower suspension arm Bolt A
Bolt B
(See page MX±4) Nut C181
32
361,850
330
370134
24
27
Flywheel housing under cover x Transaxle7.88069 in.´lbf
Shift cable grommet retainer x Body4.95043 in.´lbf
Shift lever assembly x Body121209
No.2 selecting bellcrank with selecting bellcrank support2020014
Shift and select lever shaft lock bolt4950036
Shift and select lever shaft assembly x Transmission case2020014
Transmission case cover x Transmission case2930022
Breather plug4950036
Output shaft lock nut1231,25090
Shift fork and shift head set bolt2424017
Rear bearing retainer x Transmission case4243031
Straight screw plug2525018
Straight screw plug (Reverse restrict pin)131309
Reverse idler gear shaft lock bolt2930022
Transmission case x Transaxle case2930022
Transmission oil pipe x Transaxle case1717513
Reverse shift arm bracket assembly x Transaxle case1717513

Page 3287 of 4592

TOYOTA CAMRY 1999 Service Repair Manual ± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
SS±49
212 Author: Date:
Transmission oil pump assembly x Transaxle case1717513
Transaxle case receiver x Transaxle case7.47565 in.´lbf
Clutch relea

Page 3288 of 4592

TOYOTA CAMRY 1999 Service Repair Manual SS09M±01
SS±50
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (S51)
213 Author: Date:
MANUAL TRANSAXLE (S51)
SERVICE DATA
Input shaft roller bearing journal diameterMin.29.970 mm (1.799 in.)
Input shaf

SS09M±01
SS±50
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (S51)
213 Author: Date:
MANUAL TRANSAXLE (S51)
SERVICE DATA
Input shaft roller bearing journal diameterMin.29.970 mm (1.799 in.)
Input shaft 3rd gear journal diameterMin.33.090 mm (1.3028 in.)
Input shaft 4th gear journal diameterMin.32.470 mm (1.2783 in.)
Input shaft 5th gear journal diameterMin.26.970 mm (1.0618 in.)
Input shaft runoutMax.0.05 mm (0.0020 in.)
Output shaft roller bearing journal diameterMin.31.970 mm (1.2587 in.)
Output shaft 1st gear journal diameterMin.37.970 mm (1.4949 in.)
Output shaft 2nd gear journal diameterMin.31.990 mm (1.2594 in.)
Output shaft runoutMax.0.05 mm (0.0020 in.)
Gear thrust clearance 1st STD0.10 ± 0.29 mm (0.0039 ± 0.0114 in.)Gear thrust clearance 1st STD
Max.
0.10 0.29 mm (0.0039 0.0114 in.)
0.35 mm (0.0138 in.)
Gear thrust clearance 2nd STD0.20 ± 0.44 mm (0.0079 ± 0.0173 in.)Gear thrust clearance 2nd STD
Max.
0.20 0.44 mm (0.0079 0.0173 in.)
0.50 mm (0.0197 in.)
Gear thrust clearance 3rd STD0.10 ± 0.25 mm (0.0039 ± 0.098 in.)Gear thrust clearance 3rd STD
Max.
0.10 0.25 mm (0.0039 0.098 in.)
0.30 mm (0.0118 in.)
Gear thrust clearance 4th STD0.20 ± 0.45 mm (0.0079 ± 0.0177 in.)Gear thrust clearance 4th STD
Max.
0.20 0.45 mm (0.0079 0.0177 in.)
0.50 mm (0.0197 in.)
Gear thrust clearance 5th STD0.20 ± 0.40 mm (0.0079 ± 0.0157 in.)Gear thrust clearance 5th STD
Max.
0.20 0.40 mm (0.0079 0.0157 in.)
0.45 mm (0.0177 in.)
Gear radial clearance 1st, 2nd, 3rd, and 4th STD
Max.0.009 ± 0.053 mm (0.0004 ± 0.0021 in.)
0.070 mm (0.0028 in.)
Gear radial clearance 5th STD
Max.0.009 ± 0.050 mm (0.0004 ± 0.0020 in.)
0.070 mm (0.0028 in.)
Shift fork to hub sleeve clearance Max.1.0 mm (0.039 in.)
Synchronizer ring to gear clearance 1st, 3rd and 4th Min.0.6 mm (0.024 in.)
Synchronizer ring to gear clearance 2nd Min.0.7 mm (0.028 in.)
Differential case side bearing preload (at starting)(For use with SST)0.8 ± 1.6 N´m (8 ± 16 kgf´cm, 6.9 ± 13.9 in.´lbf)
Differential pinion to side gear backlash0.05 ± 0.20 mm (0.0020 ± 0.0079 in.)
Drive in depthDrive in depth
Input shaft front oil seal

0 ± 0.5 mm
(0 ± 0.020 in.) In ut shaft front oil seal
Reverse restrict pin slotted spring pin
0 ± 0.5 mm (0 ± 0.020 in.)
13.5 ± 0.5 mm (0.531 ± 0.020 in.) Reverse restrict in slotted s ring in
Shift and select lever shaft slotted spring pin
13.5 ± 0.5 mm (0.531 ± 0.020 in.)
23.5 ± 1.0 mm (0.925 ± 0.039 in.)
Differential side gear thrust washer thickness0 95 mm (0 0374 in )Differential side gear thrust washer thickness0.95 mm (0.0374 in.)
1 00 mm (0 0394 in )
1.00 mm (0.0394 in.)
1 05 mm (0 0413 in )1.05 mm (0.0413 in.)
1 10 (0 0433 i )1.10 mm (0.0433 in.)()
1.15 mm (0.0453 in.)()
1.20 mm (0.0472 in.)

Load next 8 pages

Page: < prev 1-10 ... 3249-3256 3257-3264 3265-3272 3273-3280 3281-3288 3289-3296 3297-3304 3305-3312 3313-3320 ... 4592 next >

differential audio battery replacement lock radiator cap tailgate