Page 417 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±111
8. INSTALL OVERDRIVE UNIT
(a) Install the overdrive brake apply gasket and overdrive
clutch apply gasket.
(b) Install the overdrive brake drum to the case.
(c) Install the new case gasket to the case.
(d) Make sure that the length from the top surface of the case
to the counter driven gear surface should be about 24 mm
(0.94 in.).
(e) Place the new gasket onto the transaxle case.
(f) Install the overdrive assembly with overdrive case to the
transaxle case.
Page 418 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±112
(g) Coat the threads of 23 mm (0.91 in.) bolts with sealer.
Sealer:
Part No.08833±00070, THREE BOND 1324 or equiva-
lent
(h) Install and tighten the 13 bolts.
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 61 mm (2.402 in.)
Bolt B 38 mm (1.496 in.)
Bolt C: 23 mm (0.906 in.)
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
9. CHECK INTERMEDIATE SHAFT END PLAY
(a) Make sure that the intermediate shaft as end play in axial
direction.
End play: 0.47±1.50 mm (0.0185±0.0591 in.)
If the end play is not within specification, check the instal-
lation of intermediate shaft.
(b) Make sure that the intermediate shaft turns smoothly.
10. INSTALL REAR PLANETARY GEAR
(a) Install the rear planetary ring gear.
(b) Place the bearing onto the ring gear.
Bearing outer diameter: 38.7 mm (1.524 in.)
Bearing inner diameter: 22.6 mm (0.890 in.)
(c) Coat the thrust washer with petroleum jelly and place it
onto the rear planetary gear.
Page 419 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±113
(d) Install the rear planetary gear.
11. INSTALL DISCS, PLATES AND FLANGE OF FIRST
AND REVERSE BRAKE
(a) Install the 6 plates and discs.
Install in order:
P=Plate D=Disc
P±D±P±D±P±D±P±D±P±D±P±D
(b) Install the flange, facing the flat end downward.
(c) Install the snap ring.
HINT: Be sure that the end gap of the snap ring is not
aligned with one of the cutouts.
12. CHECK FIRST AND REVERSE BRAKE
(a) Check the operation of the first and reverse brake piston.
Apply compressed air into the case passage and confirm
that the piston moves.
(b) Using a filler gauge, check that pack clearance of the first
and reverse brake.
Clearance:
1.92±2.68 mm (0.0756±0.1055 in.)
Page 420 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±114
13. INSTALL NO.2 ONE±WAY CLUTCH INTO CASE
(a) Place the No.2 one±way clutch with the shiny side of
flange upward.
(b) Install the one±way clutch while turning the planetary
gear clockwise with SST.
SST 09350±32014 (09351±32050)
If the planetary gear cannot turn clockwise, check the
installation of the one±way clutch.
(c) Install the snap ring.
HINT: Be sure that the end gap of the snap ring is not
aligned with one of cutouts.
(d) Coat the thrust washer with petroleum jelly and install it
onto the rear planetary gear.
14. INSTALL SECOND COAST BRAKE BAND GUIDE
15. PLACE NO.1 ONE±WAY CLUTCH
(a) Coat the thrust washer with petroleum jelly and install it
on the No.1 one±way clutch.
Page 421 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±115
(b) Place the No.1 one±way clutch onto the rear planetary
gear.
16. INSTALL SECOND BRAKE
(a) Install the flange, facing the flat end upward.
(b) Install the 3 discs and plates.
Install in order:
P=Plate D=Disc
D±P±D±P±D±P
(c) Place the piston return spring into the case.
(d) Place the second brake drum into the case.
HINT: Align the groove of the drum with the bolt.
(e) Place the snap ring into the case so that end gap is
installed into the groove.
(f) While compressing the piston return spring over the drum
with screwdriver, install the snap ring into the groove.
(g) Be sure that the end gap of the snap ring is not aligned
with one of cutouts.
Page 422 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±116
17. INSTALL NEW SECOND BRAKE GASKET
Install a new gasket until it makes contact with the second
brake drum.
18. CHECK OPERATION OF SECOND BRAKE
Apply compressed air into the second brake gasket and
confirm that the piston moves.
19. INSTALL SUN GEAR AND SUN GEAR INPUT DRUM
(a) Coat the thrust washer with petroleum jelly and install it
on the sun gear input drum.
(b) While turning the sun gear clockwise, install it into the
No.1 one±way clutch.
20. INSTALL OIL SEAL RING TO INTERMEDIATE SHAFT
HINT: After installing the oil seal ring, check that it moves
smoothly.
Page 423 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±117
21. INSTALL FRONT PLANETARY GEAR
(a) Coat the bearings with petroleum jelly, and install them
onto the both sides of planetary gear.
Bearing outer diameter: 45.5 mm (1.791 in.)
Bearing inner diameter: 30.1 mm (1.185 in.)
(b) Install the planetary gear onto the sun gear.
22. INSTALL FRONT PLANETARY RING GEAR
23. INSTALL SECOND COAST BRAKE BAND
(a) Place the band into the case.
(b) Install the pin through the oil pump mounting bolt hole.
24. INSTALL FORWARD CLUTCH AND DIRECT CLUTCH
(a) Coat the bearing with petroleum jelly and install it onto
rear side of the forward clutch.
Bearing outer diameter: 47.6 mm (1.874 in.)
Bearing inner diameter: 31.4 mm (1.236 in.)
Page 424 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±118
(b) Coat the bearing with petroleum jelly and install it onto the
front side of the forward clutch.
HINT: There are 2 different thickness bearings for adjust-
ment of the input shaft thrust play.
Bearing thickness
mm (in.)
ThicknessOuter diameterInner diameter
3.60 (0.1417)45.9 (1.807)27.7 (1.091)
4.19 (0.1650)47.1 (1.854)27.7 (1.091)
(c) Coat the thrust washer with petroleum jelly and install it
with the oil groove facing upward onto the direct clutch
drum.
(d) Mesh the hub of the forward clutch flukes with the direct
clutch discs.
HINT: Be careful that the bearing and thrust washer do not
get out of place.
(e) Install the direct clutch and forward clutch into the case.
HINT: Hold the direct clutch toward the forward clutch to
prevent the thrust washer from getting out of place.
25. INSTALL OIL PUMP INTO CASE
(a) Coat a new O±ring with ATF and install it to the oil pump.