Page 2129 of 4592
AB0119
I00144
I00178
ON
PI
(±) (+)
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±915
1150 Author: Date:
INSPECTION PROCEDURE
1 Check voltage between terminals PI and GND of cruise control ECU connector.
PREPARATION:
Tun ignition switch ON.
CHECK:
Measure voltage between terminals PI and GND of cruise con-
trol ECU connector when main switch is ON and OFF.
OK:
Switch positionVoltage
OFF10 ± 16 V
ONBelow 1.2 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI±879).
NG
2 Check combination meter (See page BE±2).
NG Replace combination meter.
OK
Check and replace cruise control ECU
(See page IN±31).
Page 2130 of 4592
I00291
Cruise Control ECU
4
PI
5
TC O
LG±R D DJ/C
J/C
B
B B O
LG±R 10
4DLC2
II3 11
C15
LG±R*1
11 DLC1
C15
J2
D4 D4
J3
D1LG±R
P±B
*2
*1: TMC Made, TMMK Made (5S±FE)
*2: TMMK Made (1MZ±FE) DI±916
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1151 Author: Date:
Diagnosis Circuit
CIRCUIT DESCRIPTION
This circuit sends a signal to the ECU that outputs DTC.
WIRING DIAGRAM
DI091±11
Page 2131 of 4592
AB0119
I00169
I00179
ON
TC E1
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±917
1152 Author: Date:
INSPECTION PROCEDURE
1 Check voltage between terminals Tc and E1 of DLC2.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminals Tc and E1 of DLC2.
OK:
Voltage: 10 ± 14 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI±879).
NG
2 Check harness and connector between cruise control ECU and DLC2, DLC2 and
body ground (See page IN±31).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU
(See page IN±31).
Page 2132 of 4592
DI±918
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1153 Author: Date:
Actuator Control Cable
INSPECTION PROCEDURE
1 Actuator control cable inspection
OK:
(a) Check that the actuator and control cable throttle link are properly installed and that the cable and link
are connected correctly.
(b) Check that the actuator and bell crank operate smoothly.
(c) Check that the cable is not loose or too tight.
OK:
Freeplay: less than 10 mm
HINT:
If the control cable is very loose, the vehicle's loss of speed going uphill will be large.
If the control cable is too tight, the idle RPM will become high.
DI092±07
Page 2133 of 4592
DI1KE±04
Vehicle Brought to Workshop
Customer Problem Analysis
Check and Clear DTC (Precheck)Items inside
are titles of pages in this manual,
with the page number in the bottom portion. See
the pages for detailed explanations.
Problem Symptom ConfirmationSymptom Simulation
Symptom
does not occur
Symptom
occurs
DTC Check
Circuit Inspection and part Inspection
DTC ChartMalfunction codeProblem Symptoms Table
Identification of Problem
Normal code
Repair
Confirmation Test
End
1
2
3
4
5
67
8
9
10
Step 2, 5 :Diagnostic steps permitting the use of the
TOYOTA hand±held tester or TOYOTA
break±out±box.
P. DI±920
P. DI±921
P. IN±21
P. DI±927 P. DI±921
P. DI±924
P. DI±928 ± DI±935
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±919
1154 Author: Date:
ENGINE IMMOBILISER SYSTEM
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshooting in accordance with the procedure on the following pages.
Page 2134 of 4592
DI1KF±04
ENGINE IMMOBLISER Check SheetInspector 's
Name:
Customer 's Name
Date Vehicle
Brought InRegistration YearRegistration No.
Frame No.
Odometer Reading/ /
/ /
Date Problem First Occurred
Frequency Problem Occurs/ /
ContinuousIntermittent ( times a day)
DTC Check1st Time
2nd TimeNormal Code
Malfunction Code (Code )
Normal CodeMalfunction Code (Code )
Symptomskm
miles
Engine does not start.
Check ItemMalfunction
Indicator LampNormal
Remains ON Does not Light Up
Immobiliser is not set.
(Engine starts with key codes other than the registered key code.)
DI±920
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1155 Author: Date:
CUSTOMER PROBLEM ANALYSIS CHECK
Page 2135 of 4592

S05335
TOYOTA hand±held tester
DLC3
DI1KG±04
N09214
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±921
1156 Author: Date:
PRE±CHECK
1. DIAGNOSIS SYSTEM
(a) Description
ECM controls the function of immobiliser on this vehicle.
Data of the immobiliser or DTC can be read form DLC3 of
the vehicle. When a trouble occurs in immobiliser, MIL
does not light ON but DTC inspection is performed.
Therefore when there seems to be a trouble with immobi-
liser, use TOYOTA hand±held tester or SST to check and
troubleshoot it.
(b) DLC3 INSPECTION
The vehicle's ECM uses ISO 9141±2 for communication.
The terminal arrangement of DLC3 complies with
SAEJ1962 and matches the ISO 9141±2 format.
Tester connectionconditionSpecified condition
7 (Bus Line) ± 5 (Signal ground)During communicationPulse generation
4 (chassis Ground) ± BodyAlways1 W or less
5 (Signal Ground) ± BodyAlways1 W or less
16 (B+) ± BodyAlways9 ± 14 V
HINT:
If your display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of OBD ll scan tool or TOY-
OTA hand±held tester to DLC3, turned the ignition switch ON
and operated the scan tool, there is a problem on the vehicle
side or tool side.
(1) If communication is normal when the tool is con-
nected to another vehicle, inspect DLC3 on the orig-
inal vehicle.
(2) If communication is still impossible when the tool is
connected to another vehicle, the problem is prob-
ably in the tool itself, so consult the Service Depart-
ment listed in the tool's instruction manual.
Page 2136 of 4592

F02201
DLC1
TE1E1
BR3904
Normal code
0.25 Sec. 0.25 Sec. DI±922
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1157 Author: Date:
2. INSPECT DIAGNOSIS
(a) Check the DTC (Using TOYOTA hand±held tester)
(1) Prepare the OBD ll scan tool (complying with SAEJ
1978) or TOYOTA hand±held tester.
(2) Connect the OBD ll scan tool or TOYOTA hand±
held tester to DLC3 under the instrument panel low-
er pad.
(3) Turn the ignition switch ON and turn the OBD ll scan
tool or TOYOTA hand±held tester switch ON.
(4) Use the OBD ll scan tool or TOYOTA hand±held
tester to check the DTCs and freeze frame data;
note them down. (For operating instructions, see
the OBD ll scan tool's instruction book.)
(5) See page DI±924 to confirm the details of the DTCs.
(b) Check the DTC (Using diagnosis check wire)
(1) Turn ignition switch ON.
(2) Using SST, connect between terminals 8 (TE1) and
3 (E1) of DLC1.
SST 09843±18040
(3) Read the diagnostic trouble code from malfunction
indicator lamp.
HINT:
If a diagnostic trouble code is not output, check the Tc ter-
minal circuit .
ECM controls the immobiliser function on this vehicle,
DTC is out put with DTC of engine.
As an example, the blinking patterns for codes; normal, 12 and
99 are as shown in the illustration.