1999 TOYOTA CAMRY Service Repair Manual

coolant temperature auxiliary battery location lock battery replacement sat nav relay

Page 4513 of 4592

TOYOTA CAMRY 1999 Service Repair Manual RADIATOR FAN AND CONDENSER FAN
40A
AM130A
CDS
15A
ECU±IG
1A 61K 1
15 2311
1115 23
4 11
111 13 4252K 6
2B 22F423 14
2F 22G1 30A
RDI
2 3
1 21 1 2
E 4 E 32C 12G 72C22H2
1B 11K 2
EA1 1IK1 5 IK2 7
II1 1
E

Page 4514 of 4592

TOYOTA CAMRY 1999 Service Repair Manual FAN MOTOR OPERATION (1MZ±FE)
With the ignition SW turned on, the current through the ECU±IG fuse flows to the FAN NO.1 relay (Coil side), FAN NO.2 relay
(Coil side) and FAN NO.3 relay (Coil side). F

FAN MOTOR OPERATION (1MZ±FE)
With the ignition SW turned on, the current through the ECU±IG fuse flows to the FAN NO.1 relay (Coil side), FAN NO.2 relay
(Coil side) and FAN NO.3 relay (Coil side). Furthermore, the current through the FAN NO.1 relay (Coil side) or the FAN NO.2
relay (Coil side) flows to TERMINAL 3 of the A/C single pressure SW to TERMINAL 2 to TERMINAL 2 of the water temp. SW
No.1 to TERMINAL 1 to GROUND, causing the FAN NO.1 relay to turn off and the FAN NO.2 relay to turn on.
1. LOW SPEED OPERATION
Only when the A/C system is activated or the water temp. SW No.2 is turned on, the A/C condenser fan motor and the
radiator fan motor rotates at low speed.
When the A/C system is activated, the current from ECU±IG fuse flows to the FAN NO.3 relay (Coil side) to TERMINAL 1 of
the diode (A/C) to TERMINAL 2 to TERMINAL (A)12 of the A/C amplifier (Manual A/C) or (B) 2 of the A/C control assembly
(Automatic A/C) causing the FAN NO.3 relay to turn on. As a result, the current through the CDS fuse flows to TERMINAL 2
of the A/C condenser fan motor to TERMINAL 1 to TERMINAL 3 of the FAN NO.2 relay to TERMINAL 5 to TERMINAL 5 of
the FAN NO.3 relay to TERMINAL 3 to TERMINAL 2 of the radiator fan motor to TERMINAL 1 to GROUND. As this flowing in
series for the motors, the motors rotate at low speed.
When the water temp. SW No.2 is turned on, the current from ECU±IG fuse flows to the FAN NO.3 relay (Coil side) to
TERMINAL 1 of the water temp. SW No.2 to GROUND, causing the FAN NO.3 relay to turn on. As a result, the current
through the CDS fuse flows the same route as above, rotating the motors at low speed.
2. HIGH SPEED OPERATION
Only when the A/C single pressure SW is turned off or the water temp. SW No.1 is turned off, the A/C condenser fan motor
and the radiator fan motor rotate at high speed.
When the A/C single pressure SW is turned off, the current from the RDI fuse flows to the FAN NO.1 relay (Point side) to
TERMINAL 2 of the radiator fan motor to TERMINAL 1 to GROUND. At the same time, the current from the CDS fuse flows
to TERMINAL 2 of the A/C condenser fan motor to TERMINAL 1 to TERMINAL 3 of the FAN NO.2 relay to TERMINAL 4 to
GROUND.
As the current flowing in parallel for the motors as above, the motors rotate at high speed.
FAN MOTOR OPERATION (5S±FE)
With the ignition SW turned on, the current through the ECU±IG fuse flows to the FAN NO.1 relay (Coil side), FAN NO.2 relay
(Coil side). furthermore, the current through the FAN NO.1 relay (Coil side) or the FAN NO.2 relay (Coil side) flows to
TERMINAL 3 of the A/C single pressure SW to TERMINAL 2 to TERMINAL 2 of the water temp. SW No.1 to TERMINAL 1 to
GROUND, causing the FAN NO.1 relay to turn off and the FAN NO.2 relay to turn on.
1. LOW SPEED OPERATION
When the ignition SW is turned on and the A/C system is activated, the A/C condenser fan motor and the radiator fan motor
rotates at low speed.
When the A/C system is activated, the current from MG CLT relay flows to the FAN NO.3 relay (Coil side) to GROUND,
causing the FAN NO.3 relay to turn on. As a result, the current through the CDS fuse flows to TERMINAL 2 of the A/C
condenser fan motor to TERMINAL 1 to TERMINAL 3 of the FAN NO.2 relay to TERMINAL 5 to TERMINAL 5 of the FAN
NO.3 relay to TERMINAL 3 to TERMINAL 2 of the radiator fan motor to TERMINAL 1 to GROUND. As this flowing in series
for the motors, the motors rotate at low speed.
2. HIGH SPEED OPERATION
Only when the A/C single pressure SW is turned off or the water temp. SW No.1 is turned off, the A/C condenser fan motor
and the radiator fan motor rotate at high speed.
When the A/C single pressure SW is turned off, the current from the RDI fuse flows to the FAN NO.1 relay (Point side) to
TERMINAL 2 of the radiator fan motor to TERMINAL 1 to GROUND. At the same time, the current from the CDS fuse flows
to TERMINAL 2 of the A/C condenser fan motor to TERMINAL 1 to TERMINAL 3 of the FAN NO.2 relay to TERMINAL 4 to
GROUND.
As the current flowing in parallel for the motors as above, the motors rotate at high speed.
A3 A/C SINGLE PRESSURE SW
3±2 : Open above approx. 15.5 kgf/cm2
(224 psi, 1520 kpa)
Closed below approx. 12.5 kgf/cm2 (181 psi, 1225 kpa)
W4 WATER TEMP. SW NO.1
2±1 : Open above approx. 95°C (203° F)
W5 WATER TEMP. SW NO.2 (1MZ±FE)
1±GROUND : Closed above approx. 90°C (194°F)
SYSTEM OUTLINE
SERVICE HINTS

Page 4515 of 4592

TOYOTA CAMRY 1999 Service Repair Manual RADIATOR FAN AND CONDENSER FAN
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
A126 (1MZ±FE)E11E30I1630A128 (5S±FE)F4A26 (1MZ±FE)R127 (1MZ±FE)
A326 (1MZ±FE)F4A28 (5S±FE)R129 (5S±FE)A328 (

Page 4516 of 4592

TOYOTA CAMRY 1999 Service Repair Manual 2 1

23

X X
X12

12

X

29

X
1
1
12X24
X2 1
12
121

X

29

X
2
X

XXXX GR

Page 4517 of 4592

TOYOTA CAMRY 1999 Service Repair Manual AIR CONDITIONING (AUTOMATIC A/C)
23 41510A
HEATER FROM POWER SOURCE SYSTEM (
SEE PAGE 50)
1W 2
6 2
IG FUS IBL E
LINK BLOCK10A
ECU±B
2J 7
L±B
HTR
RELAY
A/C BLOWER MOTOR
LINEAR CONTROLLER A33
50A HTR

Page 4518 of 4592

TOYOTA CAMRY 1999 Service Repair Manual A/C CONTROL ASSEMBLY
1
4 2 415 6
AIR INLET CONTROL
SERVO MOTOR A38
A 2
A/C MAGNETIC CLUTCH
AND LOCK SENSORM5 4 3 2 1
6
7
L±OB±L L±RL L±W
DEF F/ D FOOT B/L FACE
IG
GNDAIR VENT MODE
CONTROL SERVO MO

Page 4519 of 4592

TOYOTA CAMRY 1999 Service Repair Manual AIR CONDITIONING (AUTOMATIC A/C)
A/C CONTROL A SS EMBLY
1 2
M3 4 1 2
B±YL P G± R
A/C SOLAR SENSOR A37
AIR MIX CONTROL SERVO MOTOR A39
WARM COOL
A/C ROOM TEMP. SENSOR
A/C EVAPORATOR TEMP. SENSORA36

Page 4520 of 4592

TOYOTA CAMRY 1999 Service Repair Manual 1. HEATER BLOWER MOTOR OPERATION
Current is applied at all times through HTR fuse to TERMINAL 1 of the HTR relay. When the ignition SW is turned on,
current flows through the HEATER fuse to TERMINAL 5

1. HEATER BLOWER MOTOR OPERATION
Current is applied at all times through HTR fuse to TERMINAL 1 of the HTR relay. When the ignition SW is turned on,
current flows through the HEATER fuse to TERMINAL 5 of the HTR relay to TERMINAL 3 to TERMINAL HR of the A/C
control assembly. At the same time, current also flows from HEATER fuse to TERMINAL IG+ of the A/C control assembly.
*Low speed operation
When the blower SW (A/C control assembly) is pushed to LOW SPEED position, the current to TERMINAL HR of the
A/C control assembly flows to TERMINAL GND of the A/C control assembly to GROUND and turns the HTR relay on.
As a result, the current to TERMINAL 1 of the HTR relay flows to TERMINAL 2 of the relay to TERMINAL 2 of the
blower motor to TERMINAL 1 to TERMINAL 2 of the blower resistor to TERMINAL 6 to GROUND and causes the
blower motor to rotate at low speed.
*High speed operation
When the blower SW (A/C control assembly) is pushed to HIGH SPEED position, the current to TERMINAL HR of the
A/C control assembly flows to TERMINAL GND of the A/C control assembly to GROUND and turns the HTR relay on.
As a result, the current to TERMINAL 1 of the HTR relay flows to TERMINAL 2 to TERMINAL 2 of the blower motor to
TERMINAL 1 to TERMINAL 4 of the A/C blower motor linear controller to TERMINAL 2 to TERMINAL BLW of the A/C
control assembly (Which is activated when the blower SW is pushed to high speed position) to TERMINAL GND to
GROUND without passing through the blower resistor, causing the blower motor to rotate at high speed.
2. AIR INLET CONTROL SERVO MOTOR OPERATION
(Switching from FRESH to RECIRC)
With the ignition SW turned on, the current flows from HEATER fuse to TERMINAL IG+ of the A/C control assembly to
TERMINAL AIR to TERMINAL 7 of the air inlet control servo motor to TERMINAL 6 to TERMINAL AIF of the A/C control
assembly to TERMINAL GND to GROUND, the motor rotates and the damper moves to the RECIRC side. when the
damper operates with the A/C SW at RECIRC position, the damper position signal is input from TERMINAL 5 of the servo
motor to TERMINAL TPI of the A/C control assembly. As a result, current to the servo motor circuit is cut off by the A/C
control assembly, so the damper stops at that position.
(Switching from RECIRC to FRESH)
With the ignition SW turned on, when the RECIRC/FRESH SW is switched to the FRESH side, the current flows from
TERMINAL IG+ of the A/C control assembly to TERMINAL AIF to TERMINAL 6 of the air inlet control servo motor to
TERMINAL 7 to TERMINAL AIR of the A/C control assembly to TERMINAL GND to GROUND, The motor rotates and the
damper stops at that position.
3. AIR VENT MODE CONTROL SERVO MOTOR OPERATION
When the ignition SW turned on, the current flows from HEATER fuse to TERMINAL IG+ of the A/C control assembly.
(Switching from DEF to FACE)
The current flows from TERMINAL FACE of the A/C control assembly to TERMINAL 1 of the air vent mode control servo
motor to TERMINAL 5 to TERMINAL DEF of the A/C control assembly to TERMINAL GND to GROUND. The motor rotates
and the damper moves to the FACE side. When the damper operates with the A/C SW at FACE position, the damper
position signal is input from TERMINAL 5 of the servo motor to the TERMINAL DEF of the A/C control assembly. As a
result, current to the servo motor circuit is cut off by the A/C control assembly, so the damper stops at that position.
(Switching from FACE to DEF)
The current flows from TERMINAL DEF of the A/C control assembly to TERMINAL 5 of the air vent control servo motor to
TERMINAL 1 to TERMINAL FACE of the A/C control assembly to TERMINAL GND to GROUND, the motor rotates and the
damper stops at that position.
4. AIR MIX CONTROL SERVO MOTOR OPERATION
When the temperature control SW (A/C control assembly) is turned to the ºCOOLº side the current flows from TERMINAL
AMC of the A/C control assembly to TERMINAL 1 of the air mix control servo motor to motor to TERMINAL 2 to
TERMINAL AMH of the A/C control assembly to GROUND and the motor rotates. The damper opening angle at this time
is input from TERMINAL 3 of the servo motor to TERMINAL TP of the A/C control assembly, this is used to determine the
DAMPER STOP position and maintain the set temperature.
When the temperature control SW (A/C control assembly) is turned to the ºHOTº side, the current flows from servo motor
to TERMINAL AMH of the A/C control assembly to TERMINAL 2 of the air mix control servo motor to motor to TERMINAL
1 to TERMINAL AMC of the A/C control assembly, rotating the motor in reverse and switching the damper from ºCOOLº to
ºHOTº side.
SYSTEM OUTLINE

Load next 8 pages

Page: < prev 1-10 ... 4481-4488 4489-4496 4497-4504 4505-4512 4513-4520 4521-4528 4529-4536 4537-4544 4545-4552 ... 4592 next >

night vision coolant oil ESP climate control remote control