Page 385 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±79
7. REMOVE OIL STRAINER, NO.1 LOWER VALVE BODY
COVER GASKETS AND CHECK VALVE
(a) Remove the 2 gaskets and plate from the lower valve
body.
(b) Remove the oil strainer, check valve and spring.
8. REMOVE PRESSURE RELIEF VALVE
9. REMOVE NO.2 LOWER VALVE BODY COVER, OIL
STRAINER, CHECK BALLS AND VIBRATING STOP-
PER
Remove the 11 bolts and lower valve body cover.
(b) Remove the 2 check balls, oil strainer and vibrating stop-
per.
Page 386 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±80
10. REMOVE NO.2 LOWER VALVE BODY COVER GAS-
KETS AND CHECK BALLS
(a) Remove the 2 screws from the lower valve body cover.
(b) Remove the 2 gaskets and plate.
(c) Remove the 3 check balls from the cover.
11. REMOVE BOLTS FROM UPPER VALVE BODY
Remove the 3 bolts.
12. LIFT OFF UPPER VALVE BODY AND NO.1 PLATE AS
A SINGLE UNIT
Hold No.1 plate to the upper valve body and lift off the up-
per valve body.
HINT: Be careful that the check balls and oil strainer do
not fall out.
Page 387 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±81
13. REMOVE 2 CHECK BALLS AND VIBRATING STOP-
PER FROM UPPER VALVE BODY
14. REMOVE 2 OIL STRAINERS AND CHECK BALL FROM
LOWER VALVE BODY
VALVE BODY ASSEMBLY
1. INSTALL 2 CHECK BALLS AND VIBRATING STOP-
PER TO UPPER VALVE BODY
2. INSTALL 2 OIL STRAINERS AND CHECK BALL TO
LOWER VALVE BODY
3. POSITION PLATE AND NEW GASKETS ON UPPER
VALVE BODY
Position new No.1 gasket, plate and the new No.2 gasket
on the upper valve body.
HINT: Since No.1 gasket and No.2 gasket are similar, use
the illustration below to discriminate between them.
AX0TX±01
Page 388 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±82
4. PLACE UPPER VALVE BODY WITH PLATE AND GAS-
KETS ON LOWER VALVE BODY
Hold the upper valve body, plate and gaskets securely so
they do not separate.
Align each bolt hole in the valve bodies with the gaskets
and plate.
5. INSTALL AND FINGER TIGHTEN BOLTS IN UPPER
VALVE BODY TO SECURE LOWER VALVE BODY
Install and finger tighten the 3 bolts.
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 44 mm (1.732 in.)
Bolt B: 16 mm (0.630 in.)
6. INSTALL NO.2 LOWER VALVE BODY COVER GAS-
KETS, PLATE AND 3 CHECK BALLS
(a) Install the 3 check balls into the No.2 lower valve body
cover.
Page 389 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±83
(b) Position a new gasket and plate and then another new
gasket.
HINT: Both gaskets are identical.
(c) Install the 2 screws.
8. INSTALL NO.2 LOWER VALVE BODY COVER
(a) Position the No.2 lower valve body cover.
(b) Install and finger tighten the 11 bolts.
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 40 mm (1.575 in.)
Bolt B: 44 mm (1.732 in.)
Bolt C: 14 mm (0.551in.)
9. INSTALL OIL STRAINER AND CHECK VALVE
Install the oil strainer and check valve into the lower valve
body.
Page 390 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±84
10. INSTALL LOWER VALVE BODY COVER GASKETS
AND NO.2 PLATE
Position a new gasket and plate and then another new
gasket.
HINT: Both gaskets are identical.
11. INSTALL LOWER VALVE BODY COVER
(a) Position the lower valve body cover.
(b) Install and finger tighten the 5 bolts.
HINT: Each bolt length is indicated below.
Bolt length
Bolt A: 47 mm (1.850 in.)
Bolt B: 14 mm (0.551 in.)
12. INSTALL PRESSURE RELIEF VALVE
13. TIGHTEN BOLTS OF UPPER AND LOWER VALVE BO-
DIES
(a) Tighten the 16 bolts in the lower valve body.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
(b) Tighten the 3 bolts in the upper valve body.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
14. INSTALL B0 ACCUMULATOR ASSEMBLY
(a) Coat new O±rings with ATF and install them to the piston.
(b) Install the spring and piston into the cylinder.
Spring dimensions
mm (in.)
ColorFree lengthCoil outer diameter
Inner White47.5 (1.870)18.9 (0.744)
Outer None16.3 (0.642)20.7 (0.815)
Page 391 of 4592
AUTOMATIC TRANSAXLEVALVE BODY ±
AX±85
(d) Install the B
0 accumulator assembly.
(e) Install the torque the 3 bolts.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
15. INSTALL LOCK PLATE
16. INSTALL SOLENOIDS
(a) Coat new O±rings with ATF and install them to the sole-
noids.
(b) Install the lock±up solenoid.
(c) Install and torque the bolt.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
(d) Install the No.4 solenoid.
(e) Install and torque the bolt.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
(d) Install No.1 and No.2 solenoids.
(e) Install and torque the 3 bolts.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
Page 392 of 4592
AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±86
UPPER VALVE BODY
COMPONENTS
AX047±03