Page 569 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±120
(b) Using SST, measure the piston stroke while applying and
releasing compressed air (392±785 kPa, 4±8 kgf/cm
2,
57±114 psi).
SST 09240±00020
Piston stroke:
2.0±3.5 mm (0.079±0.138 in.)
If the stroke is more than specified, replace the piston rod
with a longer one.
Piston rod length:
95.2 mm (3.748 in.)
96.3 mm (3.791 in.)
If the still more than standard value, replace the brake
band with a new one.
HYDRAULIC CONTROL UNIT INSTALLATION
1. INSTALL ACCUMULATOR PISTONS AND SPRINGS
(a) Install the new O±rings to the pistons.
(b) Install the springs and pistons into the bores.
Spring dimensions
mm (in.)
Spring ColorFree length
C2Yellow/Purple51.8 (2.039)
B2None88.2 (3.473)
B2None70.3 (2.767)
C1None73.6 (2.898)
(c) Place the cover with a new gasket and gradually tighten
the bolts a little at a time in sequence.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
AX0U3±02
Page 570 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±121
2. PLACE NEW SECOND BRAKE APPLY GASKET
3. INSTALL SOLENOID WIRE
4. INSTALL THROTTLE CABLE
5. INSTALL VALVE BODY TO TRANSAXLE CASE
(a) While holding the cam down with your hand, slip the cable
end into the slot.
(b) Lower the valve body into place.
NOTICE: Do not entangle the solenoid wire.
Page 571 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±122
(c) Install and tighten the 9 bolts.
HINT:
Each bolt length is indicated below.
Hand tighten the 9 bolts first, then torque with a
torque wrench.
Bolt length:
Bolt A: 30 mm (1.181 in.)
Bolt B: 43 mm (1.693 in.)
Bolt C: 48 mm (1.890 in.)
Bolt D: 52 mm (2.047 in.)
Torque: 11 N´m (110 kgf´cm, 8 ft´lbf)
6. INSTALL B3 APPLY PIPE
NOTICE: Be careful not to bend or damage the pipe.
7. INSTALL CONNECTOR CLAMP AND PIPE RETAINER
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 48 mm (1.890 in.)
Bolt B: 39 mm (1.535 in.)
Torque: 11 N´m (110 kgf´cm, 8 ft´lbf)
8. CONNECT SOLENOID CONNECTORS
Page 572 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±123
9. INSTALL OIL PIPES
Using a plastic hammer, install the pipes into the posi-
tions.
NOTICE: Be careful not to bend or damage the pipes.
10. INSTALL MANUAL VALVE BODY AND DETENT
SPRING
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 22 mm (0.866 in.)
Bolt B: 37 mm (1.457 in.)
(a) Align the manual valve with the pin on the manual shaft
lever.
(b) Lower the manual valve body into place.
(c) Hand tighten the 5 bolts first. Then, tighten them with a
torque wrench.
Torque: 11 N´m (110 kgf´cm, 8 ft´lbf)
(d) Place the detent springs on the manual valve body and
hand tighten the 2 bolts first.
Then, tighten them with a torque wrench.
Torque: 11 N´m (110 kgf´cm, 8 ft´lbf)
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 14 mm (0.551 in.)
Bolt B: 37 mm (1.457 in.)
(e) Check that the manual valve lever is touching the center
of the detent spring tip roller.
11. INSTALL PIPE BRACKET AND OIL STRAINER
Each bolt length is indicated below.
Bolt length:
Bolt A: 22 mm (0.866 in.)
Bolt B: 53 mm (2.087 in.)
Torque:
Pipe bracket: 10 N´m (100 kgf´cm, 7 ft´lbf)
Oil strainer: 11 N´m (110 kgf´cm, 8 ft´lbf)
Page 573 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±124
12. INSTALL MAGNETS IN PLACE
NOTICE: Make sure that the magnets do not interfere with
the oil pipes.
13. INSTALL OIL PAN WITH NEW GASKET
(a) Install a new gasket and oil pan.
(b) Install and torque the 17 bolts.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
14. INSTALL THROTTLE CABLE RETAINING PLATE
15. INSTALL TRANSAXLE UPPER COVER
16. INSTALL T/M REVOLUTION SENSOR
(a) Install a new O±ring to the T/M revolution sensor.
(b) Install the T/M revolution sensor with the bolt.
Page 574 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±125
17. INSTALL PARK/NEUTRAL POSITION SWITCH
(a) Install the park/neutral position switch to the manual valve
shaft.
(b) Place the new locking plate and tighten the nut.
(c) Stake the nut with locking plate.
(d) Install the 2 bolts.
(e) Adjust the park/neutral position switch.
HINT: Align the groove and neutral basic line.
(f) Tighten the 2 bolts.
18. INSTALL UNION AND ELBOW
(a) Install the new O±rings to the union and elbow.
(b) Install the union elbow to the transaxle case.
Torque: 27 N´m (275 kgf´cm, 20 ft´lbf)
HINT: Install the elbow, as shown in the illustration.
19. INSTALL MANUAL SHAFT LEVER
Page 575 of 4592
AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±126
20. INSTALL SHIFT CONTROL CABLE BRACKET
Page 576 of 4592
AUTOMATIC TRANSAXLESERVICE SPECIFICATIONS ±
AX±127
SERVICE SPECIFICATIONS
SERVICE DATE
Second Coast Brake
Piston stroke2.0 ± 3.5 mm
0.079 ± 0.138 in.
Piston rod length95.2 mm
3.748 in.
96.3 mm
3.791 in.
Oil Pump
Body clearance STD0.07 ± 0.15 mm
0.0028 ± 0.0059 in.
Maximum0.30 mm
0.0118 in.
Tip clearance STD0.11 ± 0.14 mm
0.0043 ± 0.0055 in.
Maximum0.30 mm
0.0118 in.
Side clearance STD0.02 ± 0.05 mm
0.0008 ± 0.0020 in.
Maximum0.10 mm
0.0039 in.
Pump body bushing inside diameterMaximum38.18 mm
1.5031 in.
Stator shaft bushing inside diameter
Front side Maximum21.57 mm
0.8492 in.
Rear side Maximum27.07 mm
1.0657 in.
Direct Clutch
Piston stroke0.91 ± 1.35 mm
0.0358 ± 0.0531 in.
Drum bushing inside diameter48.27 mm
1.9004 in.
Flange thickness
2.70 mm
0.1063 in.
3.00 mm
0.1181 in.
Forward Clutch
Piston stroke1.79 ± 2.21 mm
0.0704 ± 0.0870 in.
Flange thickness
2.30 mm
0.0906 in.
2.70 mm
0.1063 in.
AX0H1±06