Page 497 of 4592
AUTOMATIC TRANSAXLEFORWARD CLUTCH ±
AX±48
2. INSTALL CLUTCH PISTON TO CLUTCH DRUM
(a) Install the 2 new O±rings to the piston.
(b) Coat the O±ring with ATF.
(c) Press the piston into the drum with the cup side up, being
careful not to damage the O±rings.
3. INSTALL PISTON RETURN SPRINGS
(a) Place the return spring and snap ring onto the piston.
(b) Place SST on the spring retainer, and compress the
springs with a press.
SST 09350±32014 (09351±32070)
(c) Install the snap ring with snap ring pliers.
Be sure the end gap of the snap ring is not aligned with
the spring retainer claw.
4. INSTALL PLATES, DISCS AND FLANGE
(a) Install the plates and discs.
Install in order:
P=Plate D=Disc
P±D±P±D±P±D±P±D±P±D
(b) Install the flange with the flat end facing downward.
5. INSTALL SNAP RING
Check that the end gap of snap ring is not aligned with one
of the cutouts.
Page 498 of 4592
AUTOMATIC TRANSAXLEFORWARD CLUTCH ±
AX±49
6. RECHECK PISTON STROKE OF FORWARD CLUTCH
Install a dial indicator and measuring terminal (SST) to-
gether, measure the forward clutch piston stroke while ap-
plying and releasing compressed air (392±785 kPa, 4±8
kgf/cm
2, 57±114 psi).
SST 09350±32014 (09351±32190)
Piston stroke:
1.79±2.21 mm (0.0704±0.0870 in.)
If the piston stroke is non±standard, select another
flange.
HINT: There are 2 different thicknesses for the flange.
Flange thickness:
2.30 mm (0.0906 in.)
2.70 mm (1.0630 in.)
Page 499 of 4592
AUTOMATIC TRANSAXLEFRONT PLANETARY GEAR ±
AX±50
FRONT PLANETARY GEAR
COMPONENTS
NO.1 ONE±WAY CLUTCH AND SUN GEAR
DISASSEMBLY
1. CHECK OPERATION OF NO.1 ONE±WAY CLUTCH
Hold the sun gear and turn the hub. The hub should turn
freely clockwise and should lock counterclockwise.
2. REMOVE NO.1 ONE±WAY CLUTCH FROM SUN GEAR
While turning the hub clockwise, remove the No.1 one±
way clutch from the sun gear.
AX03A±02
AX0TU±03
Page 500 of 4592

AUTOMATIC TRANSAXLEFRONT PLANETARY GEAR ±
AX±51
3. REMOVE SUN GEAR FROM DRUM
(a) Using snap ring pliers, remove the snap ring from the
drum.
(b) Remove the sun gear from the drum.
4. CHECK SUN GEAR BUSHINGS
Using a dial indicator, measure the inside diameter of the
sun gear bushings.
Maximum inside diameter:
22.59 mm (0.8894 in.)
If the inside diameter is greater than the maximum, re-
place the sun gear.
NO.1 ONE±WAY CLUTCH AND SUN GEAR
ASSEMBLY
1. INSTALL SUN GEAR TO DRUM
(a) Install the sun gear to the drum.
(b) Using snap ring pliers, install the snap ring to drum.
2. INSTALL NO.1 ONE±WAY CLUTCH ON SUN GEAR
While turning the hub clockwise, slide the No.1 one±way
clutch onto the sun gear.
3. RECHECK OPERATION OF NO.1 ONE±WAY CLUTCH
PLANETARY RING GEAR INSPECTION
1. INSPECT RING GEAR FLANGE BUSHING
Using a dial indicator, measure the inside diameter of the
flange bushing.
Maximum inside diameter:
30.08 mm (1.1842 in.)
If the inside diameter is greater than the maximum, re-
place the flange.
AX0TV±01
AX03D±02
Page 501 of 4592
AUTOMATIC TRANSAXLEFRONT PLANETARY GEAR ±
AX±52
2. REMOVE RING GEAR FLANGE
(a) Using a screwdriver, remove the snap ring.
(b) Remove the flange from the ring gear.
3. INSTALL RING GEAR FLANGE
(a) Position the flange into the ring gear.
(b) Using a screwdriver, install the snap ring.
FRONT PLANETARY GEAR INSPECTION
MEASURE PLANETARY PINION GEAR THRUST
CLEARANCE
Using a feeler gauge, measure the planetary pinion gear
thrust clearance.
Standard clearance:
0.16±0.56 mm (0.0063±0.0220 in.)
Maximum clearance:
0.61 mm (0.0240 in.)
If the clearance is greater than the maximum, replace the
planetary gear assembly.
AX03E±03
Page 502 of 4592
AUTOMATIC TRANSAXLESECOND BRAKE ±
AX±53
SECOND BRAKE
COMPONENTS
SECOND BRAKE PISTON DISASSEMBLY
REMOVE SECOND BRAKE PISTON
(a) Apply compressed air to the oil hole to remove the piston.
(b) Remove the 2 O±rings from the piston.
AX03F±02
AX03G±03
Page 503 of 4592
AUTOMATIC TRANSAXLESECOND BRAKE ±
AX±54
SECOND BRAKE COMPONENT INSPECTION
INSPECT DISCS, PLATES AND FLANGE
Check if the sliding surfaces of the discs, plates and
flange are worn or burnt. If necessary, replace them.
HINT:
If the lining of the disc is peeling off or discolored, or
even if a part of the printed numbers are defaced, re-
place all discs.
Before assembling new discs, soak them in ATF for
at least 15 minutes.
SECOND BRAKE PISTON ASSEMBLY
INSTALL PISTON
(a) Coat a new O±ring with ATF.
(b) Install the 2 new O±rings on the piston.
(c) Press the piston into the drum, being careful not to dam-
age the O±rings.
AX03H±03
AX03J±06
Page 504 of 4592
AUTOMATIC TRANSAXLEREAR PLANETARY GEAR ±
AX±55
REAR PLANETARY GEAR
COMPONENTS
NO.2 ONE±WAY CLUTCH DISASSEMBLY
1. CHECK OPERATION OF NO.2 ONE±WAY CLUTCH
Hold the outer race and turn the rear planetary gear. The
rear planetary gear should turn freely counterclockwise
and should lock clockwise.
2. SEPARATE NO.2 ONE±WAY CLUTCH AND REAR
PLANETARY GEAR
3. REMOVE THRUST WASHER
Remove the thrust washer from the rear side of planetary
gear.
AX03K±02
AX03L±02