Page 1577 of 3115

AB0119H01018
H01087 H10600H10630
"u
ONAirbag
Sensor
Assembly
DTC B0136/74 DLC3
TC
CG
P/T Squib LHFloor No. 1 Wire
DI-796
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
989 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0136/74 is not output.
HINT:
Codes other than code B0136/74 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
Page 1578 of 3115

H01016H08392H08396
Airbag
Sensor
Assembly
PL+
(+) (-) P/T Squib LHFloor No. 1 Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-797
990 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0137/71 Short in P/T Squib LH Circuit
(to Ground)
CIRCUIT DESCRIPTION
The P/T squib LH circuit consists of the airbag sensor assembly and the seat belt pretensioner LH.
It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0137/71 is recorded when a ground short is detected in the P/T squib LH circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0137/71
Short in P/T squib LH circuit (to ground)
P/T squib LH malfunction
Airbag sensor assembly malfunctionSeat belt pretensioner LH (P/T squib LH)
Airbag sensor assembly
Floor No. 1 wire
WIRING DIAGRAM
See page DI-790.
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-923).
2 Check floor No. 1 wire (P/T squib LH circuit).
CHECK:
Measure the resistance between the body ground and PL+ of
the floor No. 1 wire connector on the seat belt pretensioner LH
(P/T squib LH) side.
OK:
Resistance: 1 MW or Higher
NG Repair or replace floor No. 1 wire.
OK
DI6PP-16
Page 1579 of 3115

H01017H02139AB0119H01084 H10600H10631
Airbag
Sensor
Assembly
PL+
PL-
DTC B0137/71ON " u
DLC3
TC CG
P/T Squib LHFloor No. 1 Wire
DI-798
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
991 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect PL+ and PL- of the floor No.
1 wire connector on the seat belt pretensioner LH (P/T
squib LH) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0137/71 is not output.
HINT:
Codes other than code B0137/71 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Page 1580 of 3115

H01018
AB0118AB0119H01084 H10600H10632
"u
ONAirbag
Sensor
Assembly
DTC B0137/71 DLC3
TC CG
P/T Squib LH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-799
992 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0137/71 is not output.
HINT:
Codes other than code B0137/71 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.
Page 1581 of 3115

H01016AB0119
H08394H08269
Airbag
Sensor
Assembly
PL+
(-) (+) ON
P/T Squib LHFloor No. 1 Wire
DI-800
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
993 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0138/72 Short in P/T Squib LH Circuit (to B+)
CIRCUIT DESCRIPTION
The P/T squib LH circuit consists of the airbag sensor assembly and seat belt pretensioner LH.
It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0138/72 is recorded when a B+ short is detected in the P/T squib LH circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0138/72
Short in P/T squib LH circuit (to B+)
P/T squib LH malfunction
Airbag sensor assembly malfunctionSeat belt pretensioner LH (P/T squib LH)
Airbag sensor assembly
Floor No. 1 wire
WIRING DIAGRAM
See page DI-790.
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-923).
2 Check floor No. 1 wire (P/T squib LH circuit).
PREPARATION:
Connect the negative (-) terminal cable to the battery, and wait
at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and PL+
of the floor No. 1 wire connector on the seat belt preten-
sioner LH (P/T squib LH) side.
OK:
Voltage: Below 1 V
NG Repair or replace floor No. 1 wire.
OK
DI6PQ-16
Page 1582 of 3115

H01017H02139AB0119H01085 H10600H10633
Airbag
Sensor
Assembly
PL+
PL-
DTC B0138/72
ON " u
DLC3
TC CG
P/T Squib LHFloor No. 1 Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-801
994 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect PL+ and PL- of the floor No.
1 wire connector on the seat belt pretensioner LH (P/T
squib LH) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0138/72 is not output.
HINT:
Codes other than code B0138/72 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Page 1583 of 3115

AB0119H01018
H01085 H10600H10634
"u
ONAirbag
Sensor
Assembly
DTC B0138/72 DLC3
TC CG
P/T Squib LH
DI-802
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
995 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0138/72 is not output.
HINT:
Codes other than code B0138/72 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.
Page 1584 of 3115

AB0119H21169H21525
(-)
(+) ONAirbag Sensor Assembly
IG2
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-803
996 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B1100/31 Airbag Sensor Assembly Malfunction
CIRCUIT DESCRIPTION
The airbag sensor assembly consists of the airbag sensor, safing sensor, drive circuit, diagnosis circuit and
ignition control, etc.
It receives signals from the airbag sensor, judges whether or not the SRS must be activated, and detects
diagnosis system malfunction.
DTC B1100/31 is recorded when occurrence of a malfunction in the airbag sensor assembly is detected.
DTC No.DTC Detecting ConditionTrouble Area
B1100/31Airbag sensor assembly malfunctionAirbag sensor assembly
INSPECTION PROCEDURE
HINT:
When a malfunction code other than code B1100/31 is displayed at the same time, first repair the malfunction
indicated by the malfunction code other than code B1100/31.
1 Prepare for inspection (See step 1 on page DI-923).
2 Check airbag sensor assembly.
PREPARATION:
Connect the negative (-) terminal cable to the battery, and wait
at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and IG2
of the dash wire connector on the airbag sensor assembly
side.
OK:
Voltage: 10 - 14 V
NG Check that an abnormality occurs on the battery
and charging system.
OK
DI6PR-15