Page 2569 of 3115
Z00754
SST
Z04247
Yoke
Drill mark Color
Bearing
CupDrill mark
Z00755
PR0081
SST
Q07338
- PROPELLER SHAFTSPIDER BEARING
PR-9
1948 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) Install the 2 removed bearing outer races to the spider.
(e) Using SST, push out the bearing from the yoke.
SST 09332-25010
(f) Clamp the outer bearing race in a vise and tap off the yoke
with a hammer.
HINT:
Remove the bearing on the opposite side in the same proce-
dure.
6. SELECT SPIDER BEARING
Select the bearing according to whether or not there is a drill
mark on the yoke section.
YokeBearing
w/ drill markw/ color mark (Red)
No drill markNo color mark
7. INSTALL SPIDER BEARING
(a) Apply MP grease to a new spider and bearings.
NOTICE:
Be careful not to apply too much grease.
(b) Fit the spider into the yoke.
(c) Using SST, install the bearings on the spider.
SST 09332-25010
(d) Using SST, adjust both bearings so that the snap ring
grooves are at maximum and equal in width.
Page 2570 of 3115

PR0069
M00056
Thickness of snap ring:
Color
Thickness mm (in.)
Brown
Blue
2.44 - 2.46 mm
(0.0961 - 0.0969 in.)
2.46 - 2.48 mm
(0.0969 - 0.0976 in.) 2.30 - 2.32 mm
(0.0906 - 0.0913 in.)
2.34 - 2.36 mm
(0.0921 - 0.0929 in.) 2.28 - 2.30 mm
(0.0898 - 0.0906 in.)
2.32 - 2.34 mm
(0.0913 - 0.0921 in.)
2.36 - 2.38 mm
(0.0929 - 0.0937 in.)
2.38 - 2.40 mm
(0.0937 - 0.0945 in.)
2.40 - 2.42 mm
(0.0945 - 0.0953 in.)
2.42 - 2.44 mm
(0.0953 - 0.0961 in.) Mark PR-10
- PROPELLER SHAFTSPIDER BEARING
1949 Author: Date:
2004 LAND CRUISER (RM1071U)
8. INSTALL SNAP RING
(a) Install 2 new snap rings of equal thickness which will allow
0 mm (0 in.) axial play.
HINT:
Do not reuse the snap rings.
(b) Using a hammer, tap the yoke until there is no clearance
between the bearing outer race and snap ring.
9. INSTALL FLANGE YOKE TO SLEEVE YOKE (OR PRO-
PELLER SHAFT)
(a) Align the matchmarks on the propeller shaft and flange
yoke or flange yoke and sleeve yoke.
(b) Install the flange yoke to the sleeve yoke (or propeller
shaft).
HINT:
Install 2 new spider bearings and snap ring on the flange yoke
side in the procedure described above.
Page 2571 of 3115
R04447
D01633
SPIDER GREASE FITTING ASSEMBLY DIRECTION
Front propeller shaft
Rear propeller shaftThe figure at left shows the locations
of the grease fittings as seen from the
rear. No. 1
Sleeve Yoke
No. 2
No. 1No. 2
Sleeve Yoke
No. 2
No. 1 Sleeve Yoke
- PROPELLER SHAFTSPIDER BEARING
PR-1 1
1950 Author: Date:
2004 LAND CRUISER (RM1071U)
10. CHECK SPIDER BEARING (See page PR-5)
(a) Check that the spider bearing moves smoothly.
(b) Check the spider bearing axial play.
Maximum bearing axial play: 0 mm (0 in.)
HINT:
When replacing the spider bearing, be sure that the grease fit-
ting assembly hole is facing to the direction shown in the illustra-
tion.
Page 2572 of 3115
PR03H-02
- PROPELLER SHAFTTROUBLESHOOTING
PR-1
1940 Author: Date:
2004 LAND CRUISER (RM1071U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomsSuspect AreaSee page
Noise1. Sleeve yoke spline (Worn)
2. Spider bearing (Worn or stuck)PR-5
PR-5
Vibration
1. Sleeve yoke spline (Stuck)
2. Propeller shaft (Runout)
3. Propeller shaft (Imbalance)PR-5
PR-5
-
Page 2573 of 3115
SS0O3-03
SS-52
- SERVICE SPECIFICATIONSAIR CONDITIONING
192 Author: Date:
2004 LAND CRUISER (RM1071U)
AIR CONDITIONING
SERVICE DATA
Refrigerant charge volume Single A/C
Dual A/C650 ± 50 g (22.93 ± 1.76 oz.)
1,050 ± 50 g (37.03 ± 1.76 oz.)
Idle speed Magnetic clutch not engaged700 ± 50 rpmIdle s eed Magnetic clutch not engaged
Magnetic clutch engaged780 ± 50 rpm
Magnetic clutch clearance0.5 ± 0.15 mm (0.020 ± 0.0059 in.)
Page 2574 of 3115
SS0O4-04
- SERVICE SPECIFICATIONSAIR CONDITIONING
SS-53
193 Author: Date:
2004 LAND CRUISER (RM1071U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Condenser x Discharge tube5.45548 in.´lbf
Condenser x Liquid tube101007
Compressor x Discharge hose101007
Compressor x Suction hose101007
Expansion valve x Evaporator3.43530
Liquid line (Block joint)101007
Liquid line (Piping line)1414010
Discharge line (Piping joint)2222516
Suction line (Block joint)101007
Suction line (Piping joint)5/8º3233024Suction line (Pi ing joint) 5/8
3/4º4242531
Compressor x Cylinder block4950036
Page 2575 of 3115

SS0OO-02
- SERVICE SPECIFICATIONSAUTOMATIC TRANSMISSION
SS-23
163 Author: Date:
2004 LAND CRUISER (RM1071U)
AUTOMATIC TRANSMISSION
SERVICE DATA
A750F
Line pressure (Wheel locked)
Engine idling
D position
R position
AT stall (Throttle valve fully opened)
D position
R position
362 - 420 kPa (3.7 - 4.3 kgfVcm2, 53 - 61 psi)
500 - 580 kPa (5.1 - 5.9 kgfVcm2, 73 - 84 psi)
1,360 - 1,460kPa (13.9 - 14.9 kgfVcm
2, 197 - 212 psi)
1,295 - 1,415 kPa (13.2 - 14.4 kgfVcm2, 188 - 205 psi)
Engine stall revolution D and R positions2,150 150 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed
(A/C OFF) N position
700 50 rpm
Drive plate runoutMax.
Torque converter runout Max.
Torque converter clutch installation distance0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
More than 17.1 mm (0.673 in.)
Shift schedule
D position
(Throttle valve fully opened) 1 " 2
2 " 3
3 " 4
4 " 5
5 " 4
4 " 3
3 " 2
2 " 1
(Throttle valve fully closed) 4 " 5
5 " 4
3 position
(Throttle valve fully opened) 1 " 2
2 " 3
4 " 3
3 " 2
2 " 1
2 position
(Throttle valve fully opened) 1 " 2
3 " 2
2 " 1
L position
(Throttle valve fully opened) 2 " 1
45 - 57 km/h (28 - 35 mph)
79 - 90 km/h (49 - 56 mph)
113 - 128 km/h (70 - 80 mph)
165 - 180 km/h (103 - 112 mph)
158 - 173 km/h (98 - 108 mph)
105 - 117 km/h (65 - 73 mph)
70 - 78 km/h (43 - 48 mph)
35 - 41 km/h (22 - 25 mph)
32 - 38 km/h (20 - 24 mph)
24 - 29 km/h (15 - 18 mph)
45 - 57 km/h (28 - 35 mph)
79 - 90 km/h (49 - 56 mph)
119 - 132 km/h (74 - 82 mph)
70 - 78 km/h (43 - 48 mph)
35 - 41 km/h (22 - 25 mph)
45 - 57 km/h (28 - 35 mph)
80 - 88 km/h (50 - 55 mph)
35 - 41 km/h (22 - 25 mph)
41 - 47 km/h (25 - 29 mph)
Lock-up pointThrottle valve opening 5 %
D position
5th gearLock-up ON
Lock-up OFF
4 position
4th gearLock-up ON
Lock-up OFF
67 - 74 km/h (42 - 46 mph)
60 - 67 km/h (37 - 42 mph)
61 - 68 km/h (38 - 42 mph)
54 - 61 km/h (34 - 38 mph)
Page 2576 of 3115

SS0OP-02
SS-24
- SERVICE SPECIFICATIONSAUTOMATIC TRANSMISSION
164 Author: Date:
2004 LAND CRUISER (RM1071U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
No.1 vehicle speed sensor x Transfer case1616012
No.2 vehicle speed sensor x Transmission case NT
SP25.4
5.455
5548 in.´lbf
48 in.´lbf
ATF temperature sensor (for linear control ) x Valve body1111 28
ATF temperature sensor (for oil temp warning lamp ) x Valve body101007
ATF temperature sensor x Transmission case5.45548 in.´lbf
Park/neutral position switch Bolt
Nut13
3.9130
409
35 in.´lbf
Transmission control shaft lever x Transmission control rod131309
Shift solenoid lock plate x Valve body6.46557 in.´lbf
Shift solenoid S1 S2 x Valve body101027
Shift solenoid SR x Valve body6.46557 in.´lbf
Valve body x Transmission case1111 08
Oil stainer x Valve body101007
Oil pan x Transmission case4.45539 in.´lbf
Drain plug x Oil pan2020515
Parking lock pawl bracket x Transmission case7.47565 in.´lbf
Shift lever assembly x Body8.38573 in.´lbf
Control lever x Shift lever plate131309
Transmission control rod x Shift lever assembly131309
Shift lever guide housing x Shift lever plate4.95043 in.´lbf
Power steering oil cooler sub-assy x Body7.57666 in.´lbf
Oil cooler bracket x Body1211 78
Oil cooler bracket x Oil cooler4.95043 in.´lbf
Oil cooler pipe x Body4.95043 in.´lbf
Oil filler pipe121229
Transfer shift lever x Transfer shift lever rod assembly121229
Transfer shift lever boot x Body5.45548 in.´lbf
Hole plug x Transmission housing1818513
Drive plate x Torque converter clutch4849035
Oil cooler pipe union nut3434725
Crossmember Bolt
Nut50
74510
75037
54
Engine mounting insulator rear x Transmission case5960043
Transmission housing x Engine Bolt A
Bolt B71
37724
37752
27
Drive plate x Crankshaft 1st
2nd49
Turn 90°500
Turn 90°36
Turn 90°