Page 409 of 3115
BO1JS-03
H04841
H00735
- BODYFRONT WIPER AND WASHER
BO-33
2607 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE WIPER ARMS
(a) Remove the 2 caps and 2 nuts.
(b) Remove the 2 wiper arms.
2. REMOVE HOOD TO COWL TOP SEAL
3. REMOVE COWL TOP VENTILATOR LOUVERS
(a) Remove the cowl top ventilator louver RH.
(b) Remove the cowl top ventilator louver LH.
4. REMOVE WIPER MOTOR
(a) Disconnect the connector, unfasten the 4 bolts.
(b) Disconnect the wiper motor from the wiper link, then re-
move the wiper motor.
5. REMOVE WIPER LINK
(a) Loosen the 6 bolts.
(b) Remove the wiper link through the service hole.
6. REMOVE WASHER NOZZLE
(a) Disconnect the washer hose.
(b) Using a screwdriver, remove the washer nozzle.
HINT:
Tape the screwdriver tip before use.
(c) Employ the same manner described above to the other
side.
Page 410 of 3115
BO5235
Centering Bolt
Bolt with Washer
BO1J8-03
H04837
H04838
H04839
BO-6
- BODYHOOD
2580 Author: Date:
2004 LAND CRUISER (RM1071U)
HOOD
ADJUSTMENT
HINT:
Since the centering bolt is used as a hood hinge set bolt, the
hood cannot be adjusted with it on. Substitute the bolt with a
washer for the centering bolt.
1. ADJUST HOOD IN FORWARD/REARWARD AND
LEFT/RIGHT DIRECTIONS
Adjust the hood by loosening the hood side hinge bolts.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
2. ADJUST FRONT EDGE OF HOOD IN VERTICAL
DIRECTION
Adjust the hood by turning the cushions.
3. ADJUST HOOD LOCK
Adjust the lock by loosening the bolts.
Page 411 of 3115

BO1J9-03
H04840
150 mm (5.91 in.)
- BODYHOOD SUPPORT
BO-7
2581 Author: Date:
2004 LAND CRUISER (RM1071U)
HOOD SUPPORT
REPLACEMENT
1. REMOVE HOOD SUPPORT
(a) Remove the bolt and hood support from the hood.
HINT:
While supporting the hood by hand, remove the hood support
from the hood.
(b) Remove the bolt and hood support.
2. IF NECESSARY, REPLACE HOOD SUPPORT
NOTICE:
Handling the hood support
Do not disassemble the support as the cylinder is
filled with pressurized gas.
If the hood support is to be replaced, drill a 2.0 - 3.0
mm (0.079 - 0.118 in.) hole in the area shown in the il-
lustration to completely release the high pressure
gas before disposing of it.
When drilling, chips may fly out so work carefully.
The gas is colorless, odorless and non - toxic.
When working, handle the hood support carefully.
Never score or scratch the exposed part of the piston
rod, and allow any paint or oil to get on it.
Do not turn the piston rod and cylinder with the hood
support fully extended.
3. INSTALL HOOD SUPPORT
(a) Install the bolt and hood support to the body.
(b) Install the bolt and hood support to the hood.
Page 412 of 3115

BO1KK-04
H18910
Reinforcement
Floor Brace
No. 1 BraceNo. 3 Heater to
Register Duct
Instrument PanelCenter Register
Radio With A/C Control Assembly
Front Ash Receptacle Retainer Center Lower
Cluster Finish Panel
Front Ash
Receptacle BoxLower No. 2
Panel
Glove Compartment Door
Rear Console Cup Holder Box Front
Console
Panel
Front
Console Box
Rear Console
Box
Rear Radio
Control Panel
Console Rear End Panel Combination Meter
Cluster Finish
Panel
LH Lower Panel
Lower No. 1 Panel No. 2 Heater to
Register Duct
Combination
Switch
Steering WheelSteering Wheel Pad
Front Pillar Garnish
Cowl Side Trim
Front Door Scuff Plate Front Assist Grip No. 4 Heater to
Register Duct
Front Pillar Garnish
Front Assist Grip
Cowl Side Trim
Front Door Scuff Plate
AA
A
A
BBB
C
C
C
C
CC
C
C
C
D
H
A
F
20 (204, 15)
EE
Glove Compartment
Door Damper
50 (510, 37)
BB
Rear Console BoxNo. 1 Under Cover
Console Box
Hole Cover
w/ Disc Player
Changer:
B
Column Cover
Transfer
Shift
Lever
Knob
: Specified torqueN´m (kgf´cm, ft´lbf)
H
H
H
H
I
I
EE
JJ
F
F
F
F
F
H
HH
H
H
BB
BB
HH
H
H
H
H
F
F
F
FF
D Front Console
Box bracket
- BODYINSTRUMENT PANEL
BO-81
2655 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTRUMENT PANEL
COMPONENTS
Page 413 of 3115
H18911
Instrument Panel Wire
Center Bracket
Front Passenger
Airbag Assembly
Defroster Nozzle
No. 1 Side Defroster
Nozzle Duct
No. 1 Heater to
Register Duct
No. 1 RegisterNo. 5 Heater to
Register DuctNo. 4 Register No. 2 Side Defroster
Nozzle Duct
G6.0 (61, 53 in.´lbf)
Instrument Panel
: Specified torqueN´m (kgf´cm, ft´lbf)
GGG
G
G
G
G
GG
G
G
6.0 (61, 53 in.´lbf)
BO-82
- BODYINSTRUMENT PANEL
2656 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 414 of 3115
H21419
Shape
Size
ShapeSizeShape
Size
ù = 8
L =16
(0.63) (0.31)ù = 6
L =18
(0.71) (0.24)ù = 6
L =16
(0.63) (0.24)
ù = 6
L =16
(0.63) (0.24)ù = 5
L =16
(0.63) (0.20)
ù = 5
L =14
(0.55)(0.20)
ù = 6
(0.24)ù = 8
(0.31) mm (in.)
ù = 5
L =14
(0.55) (0.20)
Jù = 6
L =11
(0.43) (0.24)
IH
F
G
CBA
ED
- BODYINSTRUMENT PANEL
BO-83
2657 Author: Date:
2004 LAND CRUISER (RM1071U)
HINT:
Screw shapes and sizes are indicated in the table below. The codes (ºAº to ºIº) correspond to those indicated
on the previous page.
Page 415 of 3115

BO4IY-01
H18916
- BODYINSTRUMENT PANEL
BO-89
2663 Author: Date:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
2. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT
3. REMOVE DEFROSTER NOZZLE
4. REMOVE CENTER BRACKET
5. REMOVE NO. 1 HEATER TO REGISTER DUCT
6. REMOVE INSTRUMENT PANEL WIRE HARNESS
7. REMOVE NO. 5 HEATER TO REGISTER DUCT
8. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
Remove the 3 nuts and the front passenger airbag assembly.
Torque: 6.0 N´m (61 kgf´cm, 53 in.´lbf)
CAUTION:
Do not store the front passenger airbag assembly
with the airbag deployment side facing down.
Never disassemble the front passenger airbag as-
sembly.
NOTICE:
At the time of reassembly, please refer to the following
items.
Make sure that the front passenger airbag assembly
is installed with the specified torque.
If the front passenger airbag assembly has been
dropped, or if there are cracks, dents or other defects
in the case or the connector, replace the front passen-
ger airbag assembly with a new one.
When installing the front passenger airbag assembly,
take care that the wiring does not interfere with other
parts and is not pinched between other parts.
9. REMOVE NO. 1 REGISTER
10. REMOVE NO. 4 REGISTER
Page 416 of 3115

BO3XU-02
H21208
Center Bracket
No. 5 Heater to
Register Duct
Airbag Connector
H18914
H21406
: 5 Clips
- BODYINSTRUMENT PANEL
BO-91
2665 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. INSTALL REINFORCEMENT
2. INSTALL NO. 1 BRACE
3. INSTALL FLOOR BRACE
4. INSTALL GLOVE COMPARTMENT DOOR DAMPER
5. INSTALL NO. 4 HEATER TO REGISTER DUCT
6. INSTALL NO. 3 HEATER TO REGISTER DUCT
7. INSTALL ECM (See page SF-60)
8. INSTALL INSTRUMENT PANEL
HINT:
Install the airbag connector between the No. 5 heater to
register duct and the center bracket temporarily, then
install the instrument panel.
Remove the airbag connector before installing the lower
No. 2 panel.
(a) Install the 6 bolts, the 2 nuts and the instrument panel,
then connect the connectors.
(b) Install the 2 bolts to the front passenger airbag assembly.
Torque: 20 N´m (204 kgf´cm, 15 ft´lbf)
(c) Connect the junction connectors.
HINT:
The connectors can be connected by tightening the bolts.
9. INSTALL FRONT CONSOLE BOX AND FRONT CON-
SOLE BOX BRACKET
Install the front console box and the front console box bracket
with the 2 bolts.
10. INSTALL CENTER LOWER CLUSTER FINISH PANEL
Connect the connector, then install the center lower cluster fin-
ish panel.