Page 489 of 3115

BO1KZ-04
BO0632
BO0633
15°
45°
- BODYSEAT BELT
BO-139
2713 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
CAUTION:
Replace the seat belt assembly (outer belt, inner belt, bolts,
nuts or sill-bar) if it has been used in a severe impact. The
entire assembly should be replaced even if damage is not
obvious.
1. Except manual type:
RUNNING TEST (IN SAFE AREA)
(a) Fasten the front seat belts.
(b) Drive the car at 10 mph (16 km/h) and slam on the brakes.
Check that the belt locks and cannot be extended at this
time.
HINT:
Conduct this test in a safe area. If the belt does not lock, remove
the belt mechanism assembly and conduct the following static
check. Also, whenever installing a new belt assembly.
2. Driver 's seat belt (ELR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
HINT:
Before removing the pretensioner connector, be sure to read
the precautionary notice in the RS section.
(c) Tilt the retractor slowly.
(d) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out over 45 degrees
of tilt.
If a problem is found, replace the assembly.
3. Except driver's seat belt (ELR/ALR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
HINT:
Before removing the pretensioner connector, be sure to read
the precautionary notice in the RS section.
(c) Pull out the whole belt and measure the length of the
whole belt.
Then retract the belt slightly and pull it out again
(d) Make sure that the belt cannot be extended further.
If a problem is found, replace the assembly.
Page 490 of 3115

N10070
Full Belt Length Minus
200 mm (7.87 in.)
BO0633
15°
45°
BO5906
H05710
40° Rear No. 1 Seat
Outer Center
Seat Belt
Retractor
H05731
Rear No. 1 Seat
Outer Center
Seat Belt
BO-140
- BODYSEAT BELT
2714 Author: Date:
2004 LAND CRUISER (RM1071U)
(e) Retract the whole belt, then pull out the belt until 200 mm
(7.87 in.)of the belt remaining in the retractor.
(f) Tilt the retractor slowly.
(g) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
4. Manual type:
TESTING
(a) Adjust the belt to the proper length.
(b) Apply a firm load to the belt.
(c) Make sure that the belt does not extend.
5. INSPECT REAR NO. 1 SEAT CENTER BELT
(a) After pulling out 300 mm (11.81 in.) of the seat belt, check
that the belt is locked when pulled out quickly.
(b) Check that the belt can be pulled out 300 mm (11.81 in.)
without being locked when the seat is reclined as shown
in the illustration.
(c) Check that the belt is locked when the belt is pulled out
by a certain amount under (a) condition.
(d) When folding down the seatback forward and extracting
the seat belt slowly, check that the belt is locked after a
certain length (approx. 500 mm (19.69 in.)) of the belt has
been extracted.
Page 491 of 3115
BO4J0-01
H21009
Side Step Front Cover
Rear Cover
No. 1 Side
Step Bracket
No. 2 Side Step Bracket
: Specified torqueN´m (kgf´cm, ft´lbf)
18 (184, 13)
No. 3 Side Step Bracket
Except Full Cover Type:
No.1 LH Step
Bracket GussetNo.2 LH Step
Bracket Gusset
Side Door Step Plate No.1 Moulding
18 (184, 13)
12 (120, 9)
12 (120, 9)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
18 (184, 13)
18 (184, 13)
BO-102
- BODYSIDE STEP
2676 Author: Date:
2004 LAND CRUISER (RM1071U)
SIDE STEP
COMPONENTS
Page 492 of 3115
H21008
18 (184, 13)
18 (184, 13)No. 3 Side
Step Bracket
No. 2 Side
Step Bracket
No. 1 Side
Step BracketNo. 2 Side
Step BracketLH Step Panel
LH Side Door Step Plate Cover
LH Step Plate
x5
LH Step Cover Reinforcement
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
Full Cover Type:
: Specified torque
N´m (kgf´cm, ft´lbf)
12 (120, 9)
18 (184, 13)
18 (184, 13)
12 (120, 9)
- BODYSIDE STEP
BO-103
2677 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 493 of 3115

BO1KH-02
H05288
H05706
H05708
BO3396
H05296
BO-78
- BODYSLIDING ROOF
2652 Author: Date:
2004 LAND CRUISER (RM1071U)
ADJUSTMENT
1. REMOVE SIDE GARNISH
Before making adjustment, using a screwdriver, remove the
side garnishes.
HINT:
Tape the screwdriver tip before use.
After adjustment, reinstall the side garnishes.
2. ADJUST SLIDING ROOF GLASS IN FORWARD/REAR-
WARD AND LEFT/RIGHT DIRECTIONS
(a) Loosen the sliding roof glass installation nuts.
(b) Adjust the sliding roof glass forward/rearward or left/right.
3. ADJUST SLIDING ROOF GLASS IN UPWARD OR
DOWNWARD DIRECTIONS
(a) Loosen the screws shown in the illustration.
(b) Adjust the sliding roof glass upward or downward.
4. ADJUST SLIDING ROOF GLASS IN CLEARANCE
(Difference in left and right clearance)
(a) When the front or rear alignment is not correct, remove
the drive gear and sliding roof glass, then adjust the drive
cables.
NOTICE:
Remove the drive gear with the sliding roof fully closed.
(b) Adjust by sliding the cables forward or rearward to align
the 2 marks as shown.
(c) Install the drive gear and sliding roof glass.
Page 494 of 3115
BO1KE-02
H05287
Side Garnish
Rear Garnish Sliding Roof Glass
Front Garnish
Side GarnishSunshade Trim
Rear Drip Channel Sliding Roof Housing
Drive Cable Guide Block Cable Guide Casing
Wind Deflector Panel
Drive GearSliding Roof
Panel Stopper Sliding Roof
Guide Rail
Drive Cable
- BODYSLIDING ROOF
BO-73
2647 Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
Page 495 of 3115
BO1KG-02
H05293
H05294
H05295
H05296
H05297
BO-76
- BODYSLIDING ROOF
2650 Author: Date:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE REAR DRIP CHANNEL
(a) Using a screwdriver, remove the front side of rear drip
channel.
HINT:
Tape the screwdriver tip before use.
(b) Remove the rear drip channel as shown in the illustration.
2. REMOVE SLIDING ROOF PANEL STOPPERS
Remove the 2 screws and 2 stoppers.
3. REMOVE SUNSHADE TRIM
4. REMOVE DRIVE CABLE
(a) Remove the screw and guide rail stopper.
(b) Slide the drive cable rearward, then remove it.
HINT:
At the time of reassembly, please refer to the following items.
Adjust the drive cable to a closed and tilted down position.
Slide the cable forward or backward to align the 2 marks
as shown.
Slide the cable to the forefront with your hand.
(c) Employ the same manner described above to the other
side.
5. REMOVE WIND DEFLECTOR PANEL
Remove the 2 screws and wind deflector panel as shown in the
illustration.
Page 496 of 3115
H05298
H05299
- BODYSLIDING ROOF
BO-77
2651 Author: Date:
2004 LAND CRUISER (RM1071U)
6. REMOVE GUIDE BLOCK
(a) Remove the 2 screws and guide block.
(b) Employ the same manner described above to the other
side.
7. REMOVE SLIDING ROOF HOUSING
Remove the 6 screws and sliding roof housing.
8. REMOVE CABLE GUIDE CASING