1998 TOYOTA LAND CRUISER fuel cap release

DI-16
- DIAGNOSTICSENGINE
209 Author
: Date
:
FUEL SYS #1
Fuel system status (Bank1)/
OL or CL or OLDRIVE or OL-
FAULT or CLFAULT
Idli ft i CL

OL: Open Loop-has not yet sa-
tisfied conditions to go closed
loop.

CL: Closed Loop-using oxygen
sensor(s) as feed back for fuel
control.

OL DRIVE: Open loop due to
dri ing conditions (Po er enrich
FUEL SYS #2
Fuel system status (Bank2)/
OL or CL or OLDRIVE or OL-
FAULT or CLFAULT
Idling after warming up: CLdriving conditions (Power enrich-
ment, deceleration enlargement).

OL FAULT: Open loop due to de-
tected system fault.

CL FAULT: Closed loop, but fault
with at least one oxygen sensor
may be using single oxygen sen-
sor for fuel control.
FC IDLIdle fuel cut/
ON or OFFFuel cut operation: ON
FC IDL = ºONº when throttle valve
fully closed and engine speed is
over 1,500 rpm.
MILMIL status/
ON or OFFMIL ON: ON-
STARTER SIGStarter signal/
ON or OFFCranking: ON-
A/C SIGA/C signal/
ON or OFFA/C ON: ON-
PNP SW [NSW]Park/neutral position switch signal/
ON or OFFP or N range: ON-
ELECT LOAD SIGElectrical load signal/
ON or OFFDefogger switch ON: ON-
STOP LIGHT SWStop light switch/
ON or OFF
Brake pedal depressed: ON

Brake pedal released: OFF-
FUEL PMP SP CTLFuel pump speed control status/
ON or OFFIdling: ON-
FUEL PUMP/SPDFuel pump/speed status/
ON/H or OFF/M, LIdling: ON-
A/C MAG CLUTCHA/C magnet clutch status/
ON or OFFA/C magnet clutch ON: ON-
EVAP VSVVSV status for EVAP control/
ON or OFFVSV operating: ONVSV for EVAP is controlled by the
ECM (ground side duty control)
IGNITIONIgnition counter/
Min.: 0, Max.: 4000 to 400-
VAPOR PRESSVapor pressure/
Min.: -4.125 kPa, Max.: 2.125 kPaFuel tank cap removed:
0 kPaPressure inside of fuel tank as
read by the vapor pressure sen-
sor.
CYL #1 - CYL #8Misfire ratio of the cylinder/
Min.: 0%, Max.: 50%0%This item is displayed in only idling
*1: If no conditions are specifically stated for ºldlingº, it means the shift lever is in the N or P position, the A/C
switch is OFF and all accessory switches are OFF.

A18907
(64 to 88 km/h)
(56 to 72 km/h)
Idling
Ignition OFF
Warmed up3 minutes
7 minutes 40 to 55 mph
35 to 45 mph
- DIAGNOSTICSENGINE
DI-31
224 Author
: Date
:
2004 LAND CRUISER (RM1071U)
2. CATALYST MONITOR (O2S TYPE)
(a) Preconditions
The monitor will not run unless:

MIL is OFF.

Engine Coolant Temperature (ECT) is 75°C (167°F) or greater.

Intake Air Temperature (IAT) is -10°C (14°F) or greater
NOTICE:
The readiness test can be completed in cold ambient conditions (less than -10°C / 14°F), if the drive
pattern is repeated a second time after cycling the ignition off.
(b) Drive Pattern
(1) Connect the OBD II scan tool to the DLC3 to check monitor status and preconditions.
(2) Drive the vehicle at 40 to 55 mph (64 to 88 km/h) for approximately for 3 minutes.
NOTICE:
Drive with smooth throttle operation and avoid sudden acceleration.
If IAT is less than 10°C (50°F) when engine was started, drive the vehicle at 40 to 55 mph (64 to 88
km/h) for additional 4 minutes.
(3) Drive the vehicle at 35 to 45 mph (56 to 72 km/h) for approximately 7 minutes.
NOTICE:
Drive with smooth throttle operation and avoid sudden deceleration as much as possible with the
throttle fully closed.
(4) If readiness status does not switch to complete, make sure that the preconditions are met and
the ignition switch is turned OFF and then repeat steps (2) and (3).
(5) Release pressure in the fuel tank by removing and then reinstalling the fuel tank cap.
(6) Start the engine and immediately begin driving as directed.

- DIAGNOSTICSENGINE
DI-33
226 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(a) Preconditions
The monitor will not run unless:

MIL is OFF

Fuel level is approximately 1/2 to 3/4

Altitude is 7,800 feet (2,400 m) or less*

Engine Coolant Temperature (ECT) is between 4.4°C and 35°C (40°F and 95°F)

Intake Air Temperature (IAT) is between 4.4°C and 35°C (40°F and 95°F)

Cold Soak Procedure has been completed

Before starting the engine, the difference between ECT and IAT must be less than 7°C (13°F)
HINT:
Examples:

Scenario 1
ECT = 24°C (75°F)
IAT = 16°C (60°F)
Difference between ECT and IAT is 8°C (15°F)
" The monitor will not run because difference between ECT and IAT is greater than 7°C (13°F)

Scenario 2
ECT = 21°C (70°F)
IAT = 20°C (68°F)
Difference between ECT and IAT is 1°C (2°F)
" The monitor will run because difference between ECT and IAT is less than 7°C (13°F)
The readiness test can be completed in cold ambient conditions (less than 40°F / 4.4°C) and/or at
high altitudes (more than 7,800 feet / 2,400 m) if the drive pattern is repeated a second time after cycl-
ing the ignition off.
(b) Drive Pattern
(1) Connect the OBD II scan tool to DLC3 to check monitor status and preconditions (refer to ºaº).
(2) Release pressure in fuel tank by removing the fuel tank cap and then reinstalling it.
(3) Start the engine and allow it to idle until ECT becomes 75°C (167°F) or higher.
(4) Run the engine at 3,000 rpm for about 10 seconds.
(5) Allow the engine to idle with the A/C ON (to create slight load) for 15 to 50 minutes.
NOTICE:
If the vehicle is not equipped with A/C put a slight load on the engine by doing the following :

Securely set the parking brake.

Block the drive wheels with wheel chocks.

Allow the vehicle to idle in drive for 15 to 50 minutes.