Page 2697 of 3115
H20938
RS-66
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2341 Author: Date:
2004 LAND CRUISER (RM1071U)
3. DEPLOYMENT WHEN DISPOSING OF CURTAIN
SHIELD AIRBAG ASSEMBLY WITH AIRBAG
DEPLOYED IN COLLISION
Dispose of the curtain shield airbag assembly.
CAUTION:
The curtain shield airbag assembly is very hot when
the airbag is deployed, so leave it alone for at least 30
minutes after deployment.
Use gloves and safety glasses when handling a cur-
tain shield airbag assembly with the deployed airbag.
Do not apply water etc. to a curtain shield airbag as-
sembly with the deployed airbag.
Always wash your hands with water after completing
the operation.
(1) Remove the curtain shield airbag assembly (See
page RS-59).
(2) Place the curtain shield airbag assembly in a plastic
bag, tie the end tightly and dispose of it as the other
general parts disposal.
Page 2698 of 3115

RS0N4-09
H20931
H20932
RS-60
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2335 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. Vehicle not involved in collision:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the curtain shield airbag assembly installed in the vehicle.
Check cuts, minute cracks or marked discoloration on the
front pillar garnish and roof headlining.
2. Vehicle involved in a collision and airbag is not
deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the curtain shield airbag assembly removed from the ve-
hicle.
Check cuts, tears and cracks, or marked discolor-
ation of the curtain shield airbag assembly.
Check cuts and cracks in wire harness, and chip-
ping in connectors.
CAUTION:
For removal and installation of the curtain shield airbag as-
sembly, see page RS-59 and RS-68. Be sure to follow the
correct procedure.
3. Vehicle involved in a collision and airbag is deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the curtain shield airbag assembly removed from the ve-
hicle.
Check the deformation or cracks on the body that
the curtain shield airbag installed on.
Check the damage to the connector and wire har-
ness.
HINT:
If the body that the curtain shield airbag was installed on is de-
formed or cracked, replace it.
Page 2699 of 3115

RS0TH-03
H20929
(1)(3)
(2)(3)
(3) RS-68
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2343 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a) In the order shown in the illustration, install the curtain
shield airbag with the 8 bolts.
Torque: 9.8 N´m (100 kgf´cm, 86 in.´lbf)
CAUTION:
Pay due attention not to twist the deployment section of the
curtain shield airbag assembly.
NOTICE:
Make sure that the curtain shield airbag assembly is
installed to the specified torque.
If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.
When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.
(b) Connect the connector of the curtain shield airbag as-
sembly.
2. INSTALL ROOF HEADLINING (See page BO-101)
3. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2700 of 3115

RS0TG-03
H20929
(1)
(1)(3)
(2)
(1)
H20930
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS-59
2334 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
Never use the airbag parts from another vehicle.
When replacing parts, replace them with new parts.
1. REMOVE ROOF HEADLINING (See page BO-97)
2. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(b) In the order shown in the illustration, remove the bolts and
curtain shield airbag assembly.
HINT:
Loosen the bolt (3) before removing the bolt (2).
Bind the front and rear parts of the curtain shield airbag
assembly before removing the bolt (3).
(c) Put the removed curtain shield airbag in a clear plastic
bag and keep it in a safe place.
CAUTION:
Never disassemble the curtain shield airbag assembly.
NOTICE:
Plastic bag is not reusable.
Page 2701 of 3115

RS0N6-06
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS-67
2342 Author: Date:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the curtain shield airbag assembly or curtain shield airbag cover.
CaseReplacing part
If the curtain shield airbag has been deployed.Curtain shield airbag assembly
If the curtain shield airbag assembly has been found to be faulty in trouble-
shooting.Curtain shield airbag assembly
If the curtain shield airbag assembly has been found to be faulty during
checking items (See page RS-60).Curtain shield airbag assembly
If the front pillar garnish has been found to be faulty during checking items
(See page RS-60).Front pillar garnish
If the roof headlining has been found to be faulty during checking items
(See page RS-60).Roof headlining
If the curtain shield airbag assembly has been dropped.Curtain shield airbag assembly
CAUTION:
For removal and installation of the curtain shield airbag assembly, see page RS-59 and RS-68. Be
sure to follow the correct procedure.
Page 2702 of 3115
RS0SH-04
H20947N´m (kgf´cm, ft´lbf) : Specified torque
17.5 (178, 13)
42 (428, 31)
Striker Plate
Rear Mat Set Plate
Quarter Trim Panel
Rear Door Scuff PlateRear No. 2 Seat Rear Door Opening Trim Weatherstrip
Rear Seat Belt Anchor
Curtain Shield Airbag Sensor Assembly
Striker Plate
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-85
2360 Author: Date:
2004 LAND CRUISER (RM1071U)
CURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
COMPONENTS
Page 2703 of 3115
RS0SJ-03
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-87
2362 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. Vehicle not involved in collision:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
Do a diagnostic system check (See page DI-692).
2. Vehicle involved in collision and airbag is not deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
Do a diagnostic system check (See page DI-692).
3. Vehicle involved in collision and airbag is deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
Replace the curtain shield airbag sensor assembly (See page RS-85).
Page 2704 of 3115

RS0SL-04
H20948
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-89
2364 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the curtain shield airbag sensor assem-
bly involved in a collision when the airbag has
deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 8, refer to page BO-101.
1. INSTALL CURTAIN SHIELD AIRBAG SENSOR AS-
SEMBLY
(a) Install the curtain shield airbag sensor assembly with the
2 bolts.
Torque: 17.5 N´m (178 kgf´cm, 13 ft´lbf)
(b) Connect the connector.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL QUARTER TRIM PANEL
3. INSTALL STRIKER PLATES
4. INSTALL REAR NO. 2 SEAT
5. INSTALL REAR MAT SET PLATE
6. INSTALL REAR SEAT BELT ANCHOR
7. INSTALL REAR DOOR OPENING TRIM
8. INSTALL REAR DOOR SCUFF PLATE
9. INSPECT SRS WARNING LIGHT (See page DI-692)