Page 977 of 3115
DI-456
- DIAGNOSTICSAUTOMATIC TRANSMISSION
649 Author: Date:
2004 LAND CRUISER (RM1071U)
2 Clear the DTC and running test (See page DI-361).
CHECK:
Clear the DTC again, and check DTC again after conducting the
running test.
OK:
Normal code
OK END
NG
Repair or replace valve body (See page
AT-8).
Page 978 of 3115

- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-457
650 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC P0818 Driveline Disconnect Switch Input Circuit
CIRCUIT DESCRIPTION
The ECM detects the signal from the transfer neutral position switch.
This DTC indicates that the transfer neutral position switch remains ON.
DTC No.DTC Detecting ConditionTrouble Area
P0818
Transfer neutral position switch remains ON while vehicle run-
ning under conditions for 30 sec. (2-trip detection logic)
Vehicle speed is 25 km/h or more
Transfer shift position is HShort in transfer neutral position switch circuit
Transfer neutral position switch
ECM
MONITOR DESCRIPTION
The ECM detects whether or not the transfer gear is in the neutral position by monitoring the signal from the
transfer neutral position switch.
If the ECM detects that the transfer-case is in neutral under the following conditions, the ECM will conclude
that there is a malfunction of the transfer-case neutral position switch:
Transfer-case neutral position switch indicates that the transfer-case is in neutral.
Transfer-case shifter is in the ºHº position.
The vehicle is traveling at 25 km/h (16 mph) or more.
The neutral switch has been ON for more than thirty seconds.
If all of the above conditions are detected, the ECM will conclude that there is a malfunction of the transfer-
case neutral position switch, illuminate the MIL and store the DTC.
MONITOR STRATEGY
Related DTCsP0818Transfer neutral position switch/Verify switch cycling
Rid /C tMainTransfer neutral position switchRequired sensors/ComponentsSubVehicle speed sensor
Frequency of operationContinuous
Duration30 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever the follow-
ing DTCs are not present.See page DI-361
Vehicle speed25 km/h (16 mph) or more-
Transfer positionHigh
Ignition switch ON and time after OFF to
ON0.5 sec. or more-
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Transfer neutral switch signalON
DIB3E-02
Page 979 of 3115
D12764D13183
EC 2 1Y-G
EB1 D6
Detection SW
(Transfer Neutral Position)J/B No. 6
11
E7TFN 38
539
Y-GY-GECM
W-B
W-B
EB18
6D
6D10
If1Y-G DI-458
- DIAGNOSTICSAUTOMATIC TRANSMISSION
651 Author: Date:
2004 LAND CRUISER (RM1071U)
WIRING DIAGRAM
Page 980 of 3115
D02665
OFF-ON27±0.82mm Ball
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-459
652 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Check transfer neutral position switch.
PREPARATION:
Remove the transfer neutral position switch.
CHECK:
Check the continuity between the switch terminals when push-
ing the ball at the tip of the switch.
OK:
SwitchSpecified condition
PushContinuity
FreeNo continuity
NG Replace transfer neutral position switch.
OK
2 Check harness and connector between ECM and transfer neutral position
switch, transfer neutral position switch and body ground (See page IN-36).
NG Repair or replace the harness or connector.
OK
Check and replace the ECM (See page
IN-36
).
Page 981 of 3115

DI-460
- DIAGNOSTICSAUTOMATIC TRANSMISSION
653 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC P0973 Shift Solenoid ºAº Control Circuit Low
(Shift Solenoid Valve S1)
DTC P0974 Shift Solenoid ºAº Control Circuit High
(Shift Solenoid Valve S1)
CIRCUIT DESCRIPTION
See page DI-426.
DTC No.DTC Detection ConditionTrouble Area
P0973ECM detects short in solenoid valve S1 circuit 4 times when
solenoid valve S1 is operated (1-trip detection logic)Short in shift solenoid valve S1 circuit
Shift solenoid valve S1
ECM
P0974ECM detects open in solenoid valve S1 circuit 4 times when
solenoid valve S1 is not operated (1-trip detection logic)Open in shift solenoid valve S1 circuit
Shift solenoid valve S1
ECM
MONITOR DESCRIPTION
The ECM commands gearshift by turning the shift solenoid valves ºON/OFFº. When there is an open or short
circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stored
the DTC. And the ECM performs the fail-safe function and turns the other shift solenoid valves in good condi-
tion ºON/OFFº (In case of an open or short circuit, the ECM stops sending current to the circuit.).
MONITOR STRATEGY
RltdDTCP0973Shift solenoid valve S1/Range check (Low resistance)Related DTCsP0974Shift solenoid valve S1/Range check (High resistance)
Required sensors/ComponentsShift solenoid valve S1
Frequency of operationContinuous
Duration0.1 sec. x 2 (times) or more
MIL operation1 driving cycle
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever the follow-
ing DTCs are not present.See page DI-361
Range check (Low resistance)
SolenoidON
Range check (High resistance)
SolenoidOFF
DIB3F-02
Page 982 of 3115
D12766
S1 R
E6 W E1
Electronically Controlled
Transmission Solenoid
11ECM
R8
S18EB2
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-461
654 Author: Date:
2004 LAND CRUISER (RM1071U)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Range check (Low resistance)
Intelligent power MOS diagnosis fail signals detected while
the solenoid is operatedFail at solenoid resistance: 8 W or less
Range check (High resistance)
Intelligent power MOS diagnosis fail signals detected while
the solenoid is not operatedFail at solenoid resistance: 100 kW or more
COMPONENT OPERATING RANGE
ParameterStandard value
Shift solenoid valve S1Resistance: 11 to 15 W at 20°C (68°F)
WIRING DIAGRAM
Page 983 of 3115
1
152 3 4 5 6 7 8
9 10 11 12
13 14
D11994
S1
D11583
S1
E1
E5E6E7E8E9
DI-462
- DIAGNOSTICSAUTOMATIC TRANSMISSION
655 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Check transmission wire.
PREPARATION:
Disconnect the transmission wire connector.
CHECK:
Measure resistance between S1 of transmission wire connec-
tor and body ground.
OK:
Resistance: 11 to 15 W at 20°C (68°F)
NG Go to step 3.
OK
2 Measure resistance between terminal S1 and E1 of ECM connector.
PREPARATION:
(a) Connect the transmission wire connector.
(b) Disconnect the connector of the ECM.
CHECK:
Measure resistance between terminals S1 and E1 of ECM con-
nector.
OK:
Resistance: 11 to 15 W at 20°C (68°F)
NG Repair or replace the harness or connector
(See page IN-36).
OK
Check and replace the ECM (See page
IN-36).
Page 984 of 3115
D11991(+) (-)
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-463
656 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check shift solenoid valve S1.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Remove the shift solenoid valve S1.
CHECK:
Measure the resistance between the solenoid connector termi-
nal and the body ground.
OK:
Resistance: 11 to 15 W at 20°C (68°F)
CHECK:
Connect the battery positive lead to the solenoid connector ter-
minal and the battery negative lead to the solenoid body
ground.
OK:
Solenoid sounds operation noise.
NG Replace the shift solenoid valve S1
(See page AT-8).
OK
Repair or replace the transmission wire
(See page AT-6).