Page 2673 of 3115

B04897
Push
B04896
Pull
A07061
TOYOTA
Hand-Held
Tester
DLC3
- SFISFI SYSTEM
SF-5
1704 Author: Date:
2004 LAND CRUISER (RM1071U)
(4) Match the axis of the connector with that of the pipe,
and push in the connector until the connector
makes a ºclickº sound. In the joint part is too tight to
connect them, apply a little new engine oil on the tip
of the pipe.
(5) After finishing the connection, check if the pipe and
the connector are securely connected by pulling
them.
(6) Check if there is any fuel leakage.
(h) Take following precautions to handle the nylon tube.
(1) Pay attention not to turn the joint part of the nylon
tube and the quick connector by force when con-
necting them.
(2) Pay attention not to twist the nylon tube.
(3) Do not remove the EPDM protector on the outside
of the nylon tube.
(4) Do not connect them by bending the nylon tube.
(i) Check that there are no fuel leaks on the fuel system after
doing the maintenance.
(1) Connect the TOYOTA hand-held tester or OBD II
scan tool to the DLC3.
(2) Turn the ignition switch ON and press the TOYOTA
hand-held or OBD II scan tool tester main switch
ON.
NOTICE:
Do not start the engine.
(3) Select the ACTIVE TEST mode on the TOYOTA
hand-held tester or OBD II scan tool .
(4) Please refer to the TOYOTA hand-held tester or
OBD II scan tool operator's manual for further de-
tails.
(5) If you have no TOYOTA hand-held tester or OBD
II scan tool, connect the positive (+) and negative
(-) leads from the battery to the fuel pump connec-
tor (See page SF-7).
Page 2674 of 3115
B04892
Fuel Return Hose
Pinch
SF-6
- SFISFI SYSTEM
1705 Author: Date:
2004 LAND CRUISER (RM1071U)
(6) Pinch the fuel return hose.
The pressure in the high pressure line will rise to
approx. 392 kPa (4 kgf/cm
2, 57 psi). In this state,
check to see that there is no leak on any part of the
fuel system.
NOTICE:
Always pinch the hose. Do not bend as it may cause the
hose to crack.
(7) Turn the ignition switch OFF.
(8) Disconnect the TOYOTA hand-held tester from the
DLC3.
Page 2675 of 3115
SF1UW-01
B16447
V-Bank Cover
PS Air Hose
Air Inlet Hose for EVAP
Throttle Control
ConnectorThrottle Body
Gasket Intake Air Connector
Water Bypass Hose
18 (185, 13)
N´m (kgf´cm, ft´lbf)
Non-reusable part: Specified torque
PCV Hose
Vacuum Sensing Hose
Fuel Return Hose
PCV Hose
Water Bypass Hose
- SFITHROTTLE BODY
SF-35
1734 Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
Page 2676 of 3115
B15321B16471
Water Bypass Hose
SF0P7-13
B15320B16469Water Bypass HosePCV Hose
- SFITHROTTLE BODY
SF-37
1736 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. INSTALL THROTTLE BODY
(a) Connect the water bypass hose to the manifold thermo-
stat on the throttle body.
(b) Install a new gasket and the throttle body with the 2 bolts
and the 2 nuts.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
(c) Connect the water bypass hose and the PCV hose to the
throttle body.
(d) Connect the throttle control connector.
2. INSTALL INTAKE AIR CONNECTOR
3. FILL WITH ENGINE COOLANT (See page CO-2)
4. START ENGINE AND CHECK FOR ENGINE COOLANT
LEAKS
5. INSTALL V-BANK COVER
Page 2677 of 3115

SF1UV-01
B15313B16470
A07061
DLC3
TOYOTA
Hand-Held
Tester
B04422
ECM
VPA E2
Voltmeter
- SFITHROTTLE BODY
SF-33
1732 Author: Date:
2004 LAND CRUISER (RM1071U)
THROTTLE BODY
ON-VEHICLE INSPECTION
1. REMOVE V-BANK COVER
2. INSPECT SYSTEM OPERATION
(a) Inspect the throttle control motor for operating sound.
(1) Turn the ignition switch ON.
(2) When turning the accelerator pedal position sensor
lever, check the running sound of the motor. Also,
check that there is no friction sound.
If operation is not as specified, check the throttle control motor
(See step 3), wiring and ECM.
(b) Inspect the accelerator pedal position sensor.
(1) Connect the TOYOTA hand-held tester or OBD II
scan tool to the DLC3.
(2) Check that the MIL does not come on.
(3) When turning the accelerator pedal position sensor
lever to the full- open position, check that the
throttle valve opening percentage (THROTTLE
POS) of CURRENT DATA shows the standard val-
ue.
Standard throttle valve opening percentage:
60 % or more
If operation is not as specified, check that the accelerator pedal
position sensor (See page DI-318), wiring and ECM.
If you have no TOYOTA hand-held tester or OBD II scan tool,
measure the voltage between terminal VPA and E2 of the ECM
connector.
(c) Inspect the air assist system.
(1) Start the engine and check that the MIL does not
come on.
(2) Allow the engine to warm up to normal operating
temperature.
(3) Turn the A/C compressor ON to OFF, and check the
idle speed.
Page 2678 of 3115
B15314B16468
OhmmeterM-
M+
SF-34
- SFITHROTTLE BODY
1733 Author: Date:
2004 LAND CRUISER (RM1071U)
Idle speed (Transmission in neutral): 700 ± 50 rpm
NOTICE:
Perform inspection under the condition with no electrical
load.
(d) After checking the above (b) to (d), perform the running
test and check that there is no incongruity.
3. INSPECT THROTTLE CONTROL MOTOR
(a) Disconnect the throttle connector.
(b) Using an ohmmeter, measure the motor resistance be-
tween terminal M+ and M-.
Motor resistance: 0.3 - 100 W at 20°C (68°F)
If the resistance is not as specified, replace the throttle body.
(c) Reconnect the throttle body connector.
4. INSPECT THROTTLE POSITION SENSOR (See page
DI-84)
If necessary, replace the throttle body.
NOTICE:
Be careful not to give a shock to the throttle body.
Be careful not to disassemble the throttle body.
5. REINSTALL V-BANK COVER
Page 2679 of 3115
SF0P5-13
B15320B16469Water Bypass HosePCV Hose
B15321B16471
Water Bypass Hose
SF-36
- SFITHROTTLE BODY
1735 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE V-BANK COVER
2. DRAIN ENGINE COOLANT
3. REMOVE INTAKE AIR CONNECTOR
4. REMOVE THROTTLE BODY
(a) Disconnect the throttle control connector.
(b) Disconnect the PCV hose and the water bypass hose
from the throttle body.
(c) Remove the 2 bolts and 2 nuts, and disconnect the
throttle body from the intake manifold.
(d) Disconnect the water bypass hose from the manifold ther-
mostat on the throttle body, and remove the throttle body.
(e) Remove the gasket.
Page 2680 of 3115
SF149-05
B16454
VSV for Canister Closed Valve (CCV)
VSV Connector for Canister
Closed Valve (CCV)
Air Hose
- SFIVSV FOR CANISTER CLOSED VALVE (CCV)
SF-47
1746 Author: Date:
2004 LAND CRUISER (RM1071U)
VSV FOR CANISTER CLOSED VALVE (CCV)
COMPONENTS