1998 TOYOTA LAND CRUISER axle flange

BR0JJ-06
F05025
11 (110, 8)
74 (750, 54)
Bleeder Plug
Brake Caliper
Inner Pad Clip
Boot Piston Seal
Piston
Set Ring
Axle Hub Disc
N´m (kgf´cm, ft´lbf): Specified torque
Lithium soap base glycol grease
Disc brake grease Non-reusable part


30 (310, 22)

GasketOuter PadPad Retainer Pad Retainer Clip
Anti-squeal ShimPad Retainer
Anti-squeal Shim
123 (1,250, 90)
x5

Outer Bearing
Thrust Washer
Adjusting Nut
Lock Washer
Lock Nut

Gasket
Flange

Snap Ring

Grease Cap
x6
Plate Washer
33 (335, 24)
Cone WasherPin
64 (650, 47)
Outer Race

Inner Bearing
Outer Race

Oil seal

BR-18
- BRAKEFRONT BRAKE CALIPER
2154 Author
: Date
:
2004 LAND CRUISER (RM1071U)
FRONT BRAKE CALIPER
COMPONENTS

PP1VL-03
PP-42
- PREPARATIONSUSPENSION AND AXLE
101 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SUSPENSION AND AXLE
SST (Special Service Tools)
09023-00100Union Nut Wrench 10 mmRear axle
Rear differential
09214-7601 1Crankshaft Pulley ReplacerRear differential
09223-00010Cover & Seal ReplacerFront differential
09240-00020Wire Gauge SetFront drive shaft
09308-00010Oil Seal PullerFront differential
Rear axle
Rear differential
09308-10010Oil Seal PullerFront differential
Rear differential
09315-00022Clutch Release Bearing Remover
& ReplacerFront differential
09316-2001 1Transfer Bearing ReplacerFront drive shaft
Front suspension
09316-6001 1Transmission & Transfer Bearing
ReplacerFront differential
Rear differential
(09316-0001 1)Replacer Pipe
(09316-00021)Replacer ºAº
09330-00021Companion Flange Holding ToolFront differential
Rear differential

SS0OJ-10
SS-30
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
170 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire
inflation
pressure
Tire size
P275/70R16 Front
Rear
200 kPa (2.0 kgf/cm2, 29 psi)*220 kPa (2.2 kgf/cm2, 32 psi)
220 kPa (2.2 kgf/cm2, 32 psi)*240 kPa (2.4 kgf/cm2, 35 psi)
Vehicle height
Front A - B
Rear C - D
71 mm (2.795 in.)
51 mm (2.008 in.)
Camber
Right-left error0°05' ± 45' (0.08° ± 0.75°)
30' (0.5°) or less
Fthl
Caster
Right-left error2°30' ± 45' (2.5° ± 0.75°)
30' (0.5°) or less
Front wheel
alignmentSteering axis inclination
Right-left error12°10' ± 45' (12.17° ± 0.75°)
30' (0.5°) or less
Toe-in (total)
Rack end length difference0°06' ± 12' (0.1° ± 0.2°, 1 ± 2 mm, 0.04 ± 0.08 in.)
3.0 mm (0.118 in.) or less
Wheel angle Inside wheel
Outside wheel: Reference36°42' (33°42' - 36°42')
36.7° (33.7° - 36.7°)
32°36'
32.6°
Front axle hub preload (at starting)42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)
Front axleSnap ring thickness
1.8 mm (0.0709 in.)
2.0 mm (0.0787 in.)
2.2 mm (0.0866 in.)
2.4 mm (0.0945 in.)
2.6 mm (0.1024 in.)
2.8 mm (0.1102 in.)
Front drive shaftFront drive shaft length573.9 ± 5.0 mm (22.594 ± 0.197 in.)
Ft iUpper suspension arm ball joint turning torque1.0 - 4.4 N´m (10 - 45 kgf´cm, 8.9 - 39 in.´lbf)Front suspensionLower suspension arm ball joint turning torque0.29 - 2.94 N´m (3 - 30 kgf´cm, 2.6 - 26 in.´lbf)
Bearing backlash Max.0.6 mm (0.024 in.)
RlhftAxle shaft deviation Max.0.05 mm (0.0020 in.)Rear axle shaftAxle shaft runout Max.2.0 mm (0.079 in.)
Axle shaft flange runoutMax.0.05 mm (0.0020 in.)
*: Trailer towing
A: Ground clearance of spindle center
B: Ground clearance of lower suspension arm front bolt center
C: Ground clearance of rear axle shaft center
D: Ground clearance of lower control arm front bushing center

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-31
171 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.09 mm (0.0035 in.)
Companion flange lateral runoutMax.0.09 mm (0.0035 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.0 - 1.6 N´m (10 - 16 kgf´cm, 8.9 - 14.2 in.´lbf)
0.5 - 0.8 N´m (5 - 8 kgf´cm, 4.4 - 7.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.4 - 0.6 N´m (4 - 6 kgf´cm, 3.5 - 5.3 in.´lbf)
Ring gear runout Max.0.07 mm (0.0028 in.)
Front differentialRing gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)Front differential
Side gear backlash0.05 - 0.20 mm (0.0020 - 0.0079 in.)
Differential case runout Max.0.07 mm (0.0028 in.)
Front differential oil seal drive in depth1.5 mm (0.059 in.)
Side gear thrust washer thickness
0.9 mm (0.035 in.)
1.0 mm (0.039 in.)
1.1 mm (0.043 in.)
1.2 mm (0.047 in.)
1.3 mm (0.051 in.)

SS-34
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
174 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.10 mm (0.0039 in.)
Companion flange lateral runoutMax.0.10 mm (0.0039 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.3 - 1.8 N´m (13 - 19 kgf´cm, 11.5 - 15.9 in.´lbf)
0.64 - 0.92 N´m (6.5 - 9.4 kgf´cm, 5.7 - 8.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.38 - 0.63 N´m (3.9 - 6.5 kgf´cm, 3.3 - 5.6 in.´lbf)
Ring gear runout Max.0.05 mm (0.0020 in.)
Ring gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)
Side gear backlash0.02 - 0.15 mm (0.0008 - 0.0059 in.)
Differential case runout Max.0.04 mm (0.0016 in.)
Rear differential front oil seal drive in depth0.5 mm (0.020 in.)
Rear differential
Side gear thrust washer thickness
1.55 mm (0.061 in.)
1.60 mm (0.063 in.)
1.65 mm (0.065 in.)
1.70 mm (0.067 in.)
1.75 mm (0.069 in.)
1.80 mm (0.071 in.)
1.85 mm (0.073 in.)
1.90 mm (0.075 in.)
1.95 mm (0.077 in.)
2.00 mm (0.079 in.)
2.05 mm (0.081 in.)
2.10 mm (0.083 in.)
Tooth contact pattern adjusting washer thickness
1.050 mm (0.04134 in.)
1.075 mm (0.04232 in.)
1.100 mm (0.04331 in.)
1.125 mm (0.04429 in.)
1.150 mm (0.04528 in.)
1.175 mm (0.04626 in.)
1.200 mm (0.04724 in.)
1.225 mm (0.04823 in.)
1.250 mm (0.04921 in.)
1.275 mm (0.05020 in.)
1.300 mm (0.05118 in.)
1.325 mm (0.05217 in.)
1.350 mm (0.05315 in.)
1.375 mm (0.05413 in.)
1.400 mm (0.05512 in.)
1.425 mm (0.05610 in.)
1.450 mm (0.05709 in.)
1.475 mm (0.05807 in.)
1.500 mm (0.05906 in.)
1.525 mm (0.06004 in.)
1.550 mm (0.06102 in.)

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-35
175 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.10 mm (0.0039 in.)
Companion flange lateral runoutMax.0.10 mm (0.0039 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.3 - 1.8 N´m (13 - 19 kgf´cm, 11.5 - 15.9 in.´lbf)
0.64 - 0.92 N´m (6.5 - 9.4 kgf´cm, 5.7 - 8.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.3 - 0.5 N´m (3 - 5 kgf´cm, 2.7 - 4.4 in.´lbf)
Ring gear runout Max.0.05 mm (0.0020 in.)
Ring gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)
Side gear backlash0.02 - 0.15 mm (0.0008 - 0.0059 in.)
Differential case runout Max.0.04 mm (0.0016 in.)
Rear differential front oil seal drive in depth0.5 mm (0.020 in.)
Rear differential
(w/ Diff. Lock)
Side gear thrust washer thickness
1.55 mm (0.061 in.)
1.60 mm (0.063 in.)
1.65 mm (0.065 in.)
1.70 mm (0.067 in.)
1.75 mm (0.069 in.)
1.80 mm (0.071 in.)
1.85 mm (0.073 in.)
1.90 mm (0.075 in.)
1.95 mm (0.077 in.)
2.00 mm (0.079 in.)
2.05 mm (0.081 in.)
2.10 mm (0.083 in.)
(w/ Diff. Lock)
Ring gear backlash adjusting washer thickness Mark
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
2.67 mm (0.1051 in.)
2.70 mm (0.1063 in.)
2.73 mm (0.1075 in.)
2.76 mm (0.1087 in.)
2.79 mm (0.1098 in.)
2.82 mm (0.1110 in.)
2.85 mm (0.1122 in.)
2.88 mm (0.1134 in.)
2.91 mm (0.1146 in.)
2.94 mm (0.1157 in.)
2.97 mm (0.1169 in.)
3.00 mm (0.1181 in.)
3.03 mm (0.1193 in.)
3.06 mm (0.1205 in.)
3.09 mm (0.1217 in.)
3.12 mm (0.1228 in.)
3.15 mm (0.1240 in.)
3.18 mm (0.1252 in.)
3.21 mm (0.1264 in.)
3.24 mm (0.1276 in.)
3.27 mm (0.1287 in.)
3.30 mm (0.1299 in.)
3.33 mm (0.1311 in.)

- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-37
177 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Companion flange vertical runoutMax.0.10 mm (0.0039 in.)
Companion flange lateral runoutMax.0.10 mm (0.0039 in.)
Drive pinion preload (at starting) New bearing
Reused bearing1.3 - 1.8 N´m (13 - 19 kgf´cm, 11.5 - 15.9 in.´lbf)
0.64 - 0.92 N´m (6.5 - 9.4 kgf´cm, 5.7 - 8.1 in.´lbf)
Total preload (at starting)Drive pinion preload plus
0.38 - 0.63 N´m (3.9 - 6.5 kgf´cm, 3.3 - 5.6 in.´lbf)
Ring gear runout Max.0.05 mm (0.0020 in.)
Ring gear backlash0.13 - 0.18 mm (0.0051 - 0.0071 in.)
Side gear backlash0.02 - 0.15 mm (0.0008 - 0.0059 in.)
Differential case runout Max.0.04 mm (0.0016 in.)
Side gear thrust washer thickness (Reference)1.97 - 2.06 mm (0.0776 - 0.0811 in.)
Clutch plate thickness (Reference)1.97 - 2.03 mm (0.0776 - 0.0799 in.)
Compression spring free length (Reference)32.8 mm (1.291 in.)
Rear differential front oil seal drive in depth0.5 mm (0.020 in.)
Rear differential
(w/ LSD)
Adjusting shim thickness Mark
A
B
C
D
0.20 mm (0.0079 in.)
0.25 mm (0.0098 in.)
0.30 mm (0.0118 in.)
0.35 mm (0.0138 in.)
(w/ LSD)
Tooth contact pattern adjusting washer thickness
1.050 mm (0.04134 in.)
1.075 mm (0.04232 in.)
1.100 mm (0.04331 in.)
1.125 mm (0.04429 in.)
1.150 mm (0.04528 in.)
1.175 mm (0.04626 in.)
1.200 mm (0.04724 in.)
1.225 mm (0.04823 in.)
1.250 mm (0.04921 in.)
1.275 mm (0.05020 in.)
1.300 mm (0.05118 in.)
1.325 mm (0.05217 in.)
1.350 mm (0.05315 in.)
1.375 mm (0.05413 in.)
1.400 mm (0.05512 in.)
1.425 mm (0.05610 in.)
1.450 mm (0.05709 in.)
1.475 mm (0.05807 in.)
1.500 mm (0.05906 in.)
1.525 mm (0.06004 in.)
1.550 mm (0.06102 in.)

SS0OK-05
SS-38
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
178 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TORQUE SPECIFICATION
FRONT
Part tightenedN´mkgf´cmft´lbf
Hub bolt1311,34097
Knuckle stopper bolt lock nut4445032
Steering knuckle x Brake caliper1231,25091
Disc x Axle hub7475055
Flange x Axle hub3333524
Axle hub bearing lock nut6465047
Flexible hose x Bracket2829021
ABS speed sensor installation bolt8.08271 in.´lbf
ABS speed sensor wire harness x Steering knuckle arm1313010
ABS speed sensor wire harness bracket x Steering knuckle2829021
Steering knuckle arm x Steering knuckle1471,500108
Tie rod end x Steering knuckle arm1221,25090
Upper suspension arm x Steering knuckle11 01,12581
Lower suspension arm x Steering knuckle1591,62511 7
Oil seal x Steering knuckle1818513
Propeller shaft x Companion flange8082059
Body x No. 3 frame crossmember6869550
No. 3 frame crossmember x Differential support1861,900137
Differential support x Differential tube1861,900137
Differential support x Differential carrier7880058
Differential support x Body1861,900137
Differential carrier cover x Body1861,900137
Breather hose bracket x Carrier cover1717313
Filler plug4950036
Drain plug4950036
Differential tube x Differential carrier1051,07077
Bearing cap x Differential carrier8587063
Oil deflector x Carrier cover7.37465 in.´lbf
Carrier cover x Differential carrier4747535
Differential case x Ring gear9798572
Companion flange x Drive pinionSee page SA-47
Lower suspension arm x Shock absorber1351,400100
Piston rod x Body6870050
Torque arm x Lower suspension arm2252,300166
ABS speed sensor wire harness x Upper suspension arm1313010
Upper suspension arm x Body981,00072
Stabilizer bar link x Lower suspension arm5253038
Lower suspension arm x Body2302,350170
Stabilizer bar x Stabilizer bar link2525018
Stabilizer bar bracket x Body1818513