1998 TOYOTA LAND CRUISER lights

BE2EF-01
1
2
3
4
5
6
7
8
9
1012
13
14
15
16
17
18
19
20 1120
19
18
17
16
15
14
13
12
1110
9
8
7
6
5
4
3
2
11
2
3
4
5
6
7
8
9
1012
13
14
15
16
17
18
19
20 11
20
19
18
17
16
15
14
13
12
1110
9
8
7
6
5
4
3
2
1
I29077
Connector C15 Connector C14 Connector C13 Connector C12
- BODY ELECTRICALCOMBINATION METER
BE-63
2436 Author
: Date
:
INSPECTION
1. INSPECT COMBINATION METER CIRCUIT
Connect the connector C12, C13, C14 and C15 to the combina-
tion meter and inspect the wire harness side connectors from
the back side as shown in the table.
Tester connectionConditionSpecified condition
C12 3 (DOOR ) G dEither door is openedBelow 1 VC12-3 (DOOR-) - GroundEither door is closed10 - 14 V
C12 4 (TURN L) G d
Ignition switch ON and
turn signal switch OFF or RIGHTBelow 1 V
C12-4 (TURN-L) - GroundIgnition switch ON and
turn signal switch LEFTPulse signal is output
10 - 14 V eBelow 1 V
C12 5 (BEAM ) G dIG switch ON, light control switch OFFBelow 1 VC12-5 (BEAM+) - GroundIG switch ON, light control switch ON10 - 14 V
C12 6 (TURN R) G d
Ignition switch ON and
turn signal switch OFF or LEFTBelow 1 V
C12-6 (TURN-R) - GroundIgnition switch ON and
turn signal switch RIGHTPulse signal is output
10 - 14 V eBelow 1 V
C12-7 (BEAM-) - GroundIG switch ON, light control switch ONBelow 1 V
C12 10 (CHG ) G dIgnition switch OFFBelow 1 VC12-10 (CHG+) - GroundIgnition switch ON10 - 14 V
C12 12 (ABS) G d
Ignition switch ON and ABS warning light lights
upBelow 1 V
C12-12 (ABS) - GroundIgnition switch ON and
ABS warning light does not light up10 - 14 V
C13 8 (ILL ) G dIG switch OFFBelow 1 VC13-8 (ILL+) - GroundIG switch ON10 - 14 V

BE-64
- BODY ELECTRICALCOMBINATION METER
2437 Author
: Date
:
C13 1 1 (CHECK E/G) G dIgnition switch ON and engine is stoppedBelow 1 VC13-1 1 (CHECK E/G) - GroundIgnition switch ON and engine is running10 - 14 V
C13-14 (CTR DIFF/4WD) - GroundIgnition switch ON and
center diff. lock switch OFFBelow 1 V
C13-14 (CTR DIFF/4WD) - GroundIgnition switch ON and
center diff. lock switch ON10 - 14 V
C13 15 (SLIP) G dIG switch ON, SLIP warning light ONBelow 1.5 VC13-15 (SLIP) - GroundIG switch ON, SLIP warning light OFF10 - 14 V
C13 16 (VSC TRC) G dIG switch ON, VSC TRC indicator light ONBelow 1.5 VC13-16 (VSC TRC) - GroundIG switch ON, VSC TRC indicator light OFF10 - 14 V
C13 17 (VSC OFF) G dIG switch ON, VSC OFF indicator light ONBelow 1.5 VC13-17 (VSC OFF) - GroundIG switch ON, VSC OFF indicator light OFF10 - 14 V
C13 18 (ACTIVE TRC) G dIG switch ON, TRC OFF indicator light ONBelow 1.5 VC13-18 (ACTIVE TRC) - GroundIG switch ON, TRC OFF indicator light OFF10 - 14 V
C13 19 (RSCA OFF) G dIG switch ON, RSCA warning light ONBelow 2.0 VC13-19 (RSCA OFF) - GroundIG switch ON, RSCA warning light OFF10 - 14 V
C14-4 (AIR BAG-) - GroundIgnition switch ON and
SRS indicator light lights upBelow 1 V
C14-4 (AIR BAG-) - GroundIgnition switch ON and
SRS indicator does not light up10 - 14 V
C14 7 (OIL PRS SDR) G dIgnition switch ON and indicator ONBelow 1 VC14-7 (OIL PRS SDR) - GroundIgnition switch ON and indicator OFF10 - 14 V
C14-10 (T/M PULSE) - GroundEngine is RunningPulse generation
C14 1 1 (D BKL SW) G dIgnition switch ON and seat belt is unfastened10 - 14 VC14-1 1 (D-BKL SW) - GroundIgnition switch ON and seat belt is fastenedBelow 1 V
C14 18 (PKB SW) G d
Ignition switch ON and
parking brake lever is pulledBelow 1 V
C14-18 (PKB SW) - GroundIgnition switch ON and
parking brake lever is released10 - 14 V
C14 20 (BRAKE) G d
Ignition switch ON and brake system indicator
ONBelow 1 V
C14-20 (BRAKE) - GroundIgnition switch ON and brake system indicator
OFF10 - 14 V
C15-1 (E/G EARTH) - GroundConstantContinuity
C15-2 (MAIN FE) - GroundConstantContinuity
C15-4 (MAIN FV) - GroundIgnition switch ON4.5 - 5.5 V
C15 6 (MAIN FR) G d
Ignition switch ON and
fuel sender gauge float UPApprox. 0.5 V
C15-6 (MAIN FR) - GroundIgnition switch ON and
fuel sender gauge float DOWNApprox. 5.5 V
C15 7 (ILL ) G d
Ignition switch ON and
light control rheostat volume minimumBelow 1 V
C15-7 (ILL-) - GroundIgnition switch ON and
light control rheostat volume maximum10 - 14 V
Key unlock warning switch ON (Key is inserted)Below 1 V
C15-9 (KEY SW) - GroundKey unlock warning switch OFF
(Key is removed)10 - 14 V

I06184
F
1/2
E 321
- BODY ELECTRICALCOMBINATION METER
BE-67
2440 Author
: Date
:
6. INSPECT FUEL SENDER GAUGE VOLTAGE
(a) Apply voltage (4.5 V - 5.0 V) between terminals 2 and 3.
(b) Measure voltage between terminals 1 and 2 for each float
position.
Float position mm (in.)Voltage (V)
F: Approx. 85.3 (3.36)Approx. 4.60 ± 0.1
1/2: Approx. 1.7 (0.67)Approx. 2.45 ± 0.1
E: Approx. 91.9 (3.62)Approx. 0.30 ± 0.1
If voltage value is not as specified, replace main sender gauge.
7. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the low oil pressure
switch.
(b) Turn the ignition switch ON.
(c) Connect the terminal of wire harness side connector and
ground, then check the warning light.
8. INSPECT PARKING BRAKE WARNING LIGHT
(a) Disconnect the connector from the parking brake switch
and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
9. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connector from the brake fluid level warn-
ing switch and ground terminal on the wire harness side
connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
10. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Remove the reservoir tank cap and retainer.
(b) Disconnect the connector.
(c) Check that the continuity exists between the terminal.
(d) Use syphon, etc., to take fluid out of the reservoir tank.
(e) Check that the continuity exists between terminals.
(f) Pour the fluid back in the reservoir tank.
11. INSPECT OPEN DOOR WARNING LIGHT
(a) DIsconnect the connector from the driver door courtesy
switch and ground terminal on the wire harness side con-
nector.
(b) Turn the ignition switch ON and check that the warning
light lights up.

I24949
12 1
11 Connector C15 Connector C14
I24950
12 1
9
10Connector C15
I04107
12
4
OFF
ON
I04108
Wire Harness Side: BE-68
- BODY ELECTRICALCOMBINATION METER
2441 Author
: Date
:
12. INSPECT SEAT BELT WARNING BUZZER
(a) Disconnect the connector from the combination meter.
(b) Connect the positive (+) lead from the battery terminal 12
and negative (-) lead terminal 1.
(c) Check that the buzzer stop after 4 to 8 seconds.
(d) Check that the buzzer stops when connecting the termi-
nal 11 to the GND.
13. INSPECT KEY UNLOCK WARNING BUZZER
(a) Disconnect the connector from the combination meter.
(b) Connect the positive (+) lead from the battery terminal 12
and negative (-) lead terminal 1.
(c) Connect the negative (-) lead from battery terminal 9 and
10, check that the buzzer sound.
14. INSPECT SEAT BELT WARNING LIGHT
(a) DIsconnect the connector from the seat belt buckle switch
and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
15. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
Tester connectionBelt fastened
(Belt unfastened)
Seat belt buckle SW (D)1 - 4ON (OFF)
Seat belt buckle SW (P)2 - 4OFF (ON)
If operation is not as specified, replace the switch.
16. INSPECT SEAT BELT BUCKLE SWITCH CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.

I25809
BE2F0-01
I25810
I25811
BE-190
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
2563 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT GARAGE DOOR OPENER SWITCH
Press the switch and check that each LED (red) lights up.
Even if only one switch is found not to light up, replace it.
2. INSPECT GARAGE DOOR OPENER REGISTRATION
AND TRANSMITTING
HINT:
Use the home link tester made by KENT MORE for this test.
As it is necessary to record the code of the hand held transmit-
ter, customer's code will be erased. When the inspection com-
pletes, please register the customer's again.
(a) Check that the code of hand held transmitter for inspec-
tion can be recorded (See page BE-186).
If the code can not be registered, replace garage door opener.
(b) Press the switch which an inspection code has been reg-
istered for and check that LED (green) of the home link
tester lights up.
If the LED (green) does not light up, replace the garage door
opener.

I20844
0.4 °
3 m (9.84 ft) H 20.9 mm
(0.823 in.)
7
V RH Line
90 °
V LH Line4V LH LineV Line V RH Line 65
6
V LH LineV Line
V RH Line 6
5
6
H4
O: step No.
7
H4
20.9 mm
(0.823 in.) 1,146mm (45.1 in.) Low Beam:
High Beam:20.9 mm
(0.823 in.)
20.9 mm
(0.823 in.)
1,146mm (45.1 in.)
1,146mm
(45.1 in.)H RH and
H LH lines High Beam
Low Beam
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-35
2408 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ADJUST HEADLIGHT AIM ONLY
(a) Place the vehicle in the following conditions.

The area around the headlight is not deformed.

The vehicle is parked on a level surface.

Tire inflation pressure is the specified value.

A driver is in the driver's seat and the vehicle is in a state ready for driving (with a tank full).

The vehicle has been bounced several times.
(b) Check the headlight aiming.
(1) Prepare a thick white paper.
(2) Stand the paper perpendicular to the ground at the position 9.84 ft away from the headlights.
(3) Ensure that the center line of the vehicle and the paper face forms a 90-degree angle as shown
in the illustration.
(4) Draw a horizontal line (H line) on the paper, showing where the headlights should strike.
(5) Draw a vertical line (V line) to where the center line of the vehicle is to be.
(6) Draw 2 vertical lines (by connecting the low and high beam center marks) to where the both head-
lights should strike (V RH and V LH lines).
(7) Draw a horizontal line (by connecting the both low beam center marks) to where the headlights
should strike (H RH and H LH lines).
HINT:
The H RH and H LH line is 0.4° below the horizontal line (H line) of the light axis.
(8) Start the engine.
(9) Turn the headlights ON.
(10) Check that the headlights properly strike the position shown in the illustration.
(11) If not, adjust the lights in the vertical direction.
HINT:
As shown in the illustration, adjust each aim of the RH and LH lights.
(c) When adjusting it in the vertical direction:
Using adjusting bolt A, adjust the headlight aim to within the specified range.

BE0RO-03
I01256
1 2 3 4
5 6 7 8 LOCKACC
ON
START
I06372
N20125
1 2 OFF
ON
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE-29
2402 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK-No continuity
ACC2 - 3Continuity
ON2 - 3 - 4
6 - 7Continuity
START1 - 2 - 4
6 - 7 - 8Continuity
If continuity is not as specified, replace the switch.
2. INSPECT IGNITION KEY ILLUMINATION OPERATION
Connect the positive (+) lead from the battery to terminal 1 and
the negative (-) lead to terminal 2, and check that the indicator
light lights up.
If operation is not as specified, replace the switch.
3. INSPECT KEY UNLOCK WARNING SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
OFF (Key removed)-No continuity
ON (Key set)1 - 2Continuity
If continuity is not as specified, replace the switch.
Connect the switch connector and inspect the connector on
wire harness side from the back side, as shown.

BE2EB-01
I06147
I06148
4 6
I24668
- BODY ELECTRICALSEAT HEATER SYSTEM
BE-121
2494 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT SEAT HEATER SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
HI3 - 4
5 - 6Continuity
OFF-No continuity
LO4 - 5Continuity
Illumination circuit1 - 2Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SEAT HEATER INDICATOR LIGHT OPERA-
TION
(a) Connect the positive (+) lead from the battery to terminal
6 and the negative (-) lead to terminal 4.
(b) Push the seat heater switch Right or Left side and check
that the indicator light lights up.
If operation is not as specified, replace the switch and inspect
the circuits connected to other parts.
3. INSPECT SEAT HEATER ASSY (SEAT CUSHION)
CONTINUITY
Inspect the seat heater assy between terminals, as shown.
Tester connectionConditionSpecified condition
1 - 4ConstantContinuity
2 - 3ConstantContinuity
If continuity is not as specified, replace the seat heater assy.