Page 1705 of 2103
![MITSUBISHI SPYDER 1990 Service Repair Manual INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS .
INSPECTION PROCEDURE , .,, , __ ,
Communication with scan not possible. , .
(Communication with all is not Probablecause
[Comment]Th MITSUBISHI SPYDER 1990 Service Repair Manual INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS .
INSPECTION PROCEDURE , .,, , __ ,
Communication with scan not possible. , .
(Communication with all is not Probablecause
[Comment]Th](/manual-img/19/57345/w960_57345-1704.png)
INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS .
INSPECTION PROCEDURE , .,, , __ ,
Communication with scan not possible. , .
(Communication with all is not Probablecause
[Comment]The reason is probably a defect in supply system (including ground) forl .
the diagnostic line.. . . .
Refer to GROUP -Troubleshooting.
.I N S P E C T I O N P R O C E D U R E 2
(Communication with ABS only is not
Communication with scan tool is ,
l Blown fuseWhen the s&an tool is not possible, the cause is probab ly anopen circuit in the ABS-ECU power circuit or an ope n circuit in the diagnostic outputl Malfunction of connector
l Malfunction of ABS-ECU
circuit.. . . .
NGMeasure at data link connector Repairand ABS-ECU connector -1.lDisconnect the connector and mea-sure at the side.
Continuity between the following
terminals.OK: Continuity
ABS-ECU side to Data link
connector side C h e c k t h e between the
ABS-ECU and link connector. . . necessary.
OK.NG NGMeasure at ABS-ECU connector RepairlDisconnect the connector and mea-* and sure at the harness side.
l Ignition switch ONOK
l Voltage between terminal 18 and ground. Check trouble symptomsOK: Battery positive voltage
OKCheck the harness between fuse No.
.13 the junction block andABS-ECU. Repair, if necessary. .
Measure at ABS-ECU connector . . lDisconnect the connector and mea-sure at the harness side.l and body ground..OK: Continuity
TSB Revision
Page 1706 of 2103
![MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubleshooting , ,
INSPECTION PROCEDURE 3When ignition key is turned to “ON” (engine stopped ),
ABS warning light does not illuminate
[Comment]When power is supplied to the MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubleshooting , ,
INSPECTION PROCEDURE 3When ignition key is turned to “ON” (engine stopped ),
ABS warning light does not illuminate
[Comment]When power is supplied to the](/manual-img/19/57345/w960_57345-1705.png)
ABS Troubleshooting , ,
INSPECTION PROCEDURE 3When ignition key is turned to “ON” (engine stopped ),
ABS warning light does not illuminate
[Comment]When power is supplied to the ABS-ECU, the valve relay changes from to ON by the initial check, and thus even if there is a problem with the circuit between
ABS light and ABS-ECU, the light will illuminate once when the valve relay
is OFF.
Accordingly, the cause of the light not illuminatin g is probably an open circuit in the
light power circuit, a blown light bulb, or an open circuit in both the circuit between
the ABS
light and the ABS-ECU and the circuit between the ABS light and the ABS valve relay.When other lights also do not illuminate, the cause is probably a blown fuse.
Measure at combination meter connector
l Disconnect the connector and mea-
sure at the harness side.
l Ignition Switch ON
lVoltage between terminal 10 and body
OK Battery positive voltage Check trouble symptoms
Measure at combination meter connector
sure at the combination meter side.
l Continuitv between terminals
R e p l a c e t h e
OK Continuity ,
OK
Check the harnesses between the ABS valve relay and the combination meter,
a n d b e t w e e n t h e A B S - E C U a n d
combination meter (common section).
if necessary.
INSPECTION PROCEDURE 4
TSB Revision.
Even after the engine is started, the ABS Warning l ight ,remains illuminated.. .
[Comment]There is probably a short in the ABS warning light illumination circuit.l Malfunction of combination meterl Malfunction of ABS valve relayl Malfunction of ABS-ECU. ,
NOTE
This trouble symptom is limited to cases where comm unication with the scan tool is’
is normal) and the diagnostic trouble code is a normal diagnostic trouble code..YESDisconnect the ABS-ECU connector Does the light remain illuminated?
NO
Short circuit inside the combination or in the harnessbetween the meter and
Replace the ABS-ECU.
Page 1707 of 2103
![MITSUBISHI SPYDER 1990 Service Repair Manual When ignition key is turned ABS warning lightProbable.
does not illuminate.
[Comment]The ABS-ECU uses the the which is cut when the ignition switch is’l o f
turned to “START MITSUBISHI SPYDER 1990 Service Repair Manual When ignition key is turned ABS warning lightProbable.
does not illuminate.
[Comment]The ABS-ECU uses the the which is cut when the ignition switch is’l o f
turned to “START](/manual-img/19/57345/w960_57345-1706.png)
When ignition key is turned ABS warning lightProbable.
does not illuminate.
[Comment]The ABS-ECU uses the the which is cut when the ignition switch is’l o f
turned to “START”. The ABS light uses power which is not cut even
l when the ignition switch is turned to “START”.Accordingly, because the power to the ABS-ECU is st
opped in “START” position,
if the light does not illuminate at this time, the cause is a problem in the __ light illumination circuit in the valve relay.
N GMeasure at hydraulic unit connector NG_..l Disconnect the connector and mea- Repair
sure at the harness side.lVoltaae between terminal and bodv
v o l t a g e trouble symptom.
Replace the hydraulic unit.
INSPECTION PROCEDURE 6
The ABS warning light flashes once after the igniti on key
Probable cause
is turned to “ON”. The light
when
is turned to “START”, and when the is to
it flashes once.I[Comment]l Malfunction of wiring harness or When power flows, the ABS-ECU turns on the warning light for approximately secondl Malfunction of ABS-ECU
while it performs a valve relay test. If there is a break in the harness between the
ECU and the
light illuminates only when the valve relay is off in valve
relay test, etc.
NGMeasure at ABS-ECU connector Check the connectors:
l Disconnect the connector and mea- a n d Repair
sure at the harness side.
combination meter and the ABS-ECU.Repair, if
.
,
Repair
OK
Check trouble symptom. Replace the ABS-ECU.
TSB RevisionI
Page 1708 of 2103
![MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubfeshooting , .
INSPECTION PROCEDURE 7
Break operation is abnormal
[Comment]This varies depending on the driving conditions and the road surface conditions, soproblem diagnosis is d MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubfeshooting , .
INSPECTION PROCEDURE 7
Break operation is abnormal
[Comment]This varies depending on the driving conditions and the road surface conditions, soproblem diagnosis is d](/manual-img/19/57345/w960_57345-1707.png)
ABS Troubfeshooting , .
INSPECTION PROCEDURE 7
Break operation is abnormal
[Comment]This varies depending on the driving conditions and the road surface conditions, soproblem diagnosis is difficult. However, if a normal diagnostic trouble code is displayed,carry out the following
l Malfunction of wheel speed l Malfunction of ABS rotor
l Malfunction of wheel bearing
of hydraulic Malfunction of ABS-ECU
NG Repair
(Refer to
Wheel speed sensor output voltage check [ R e p l a c e t h e w h e e l
Hydraulic unit check (Refer to 1NGABS rotor check (Refer to Replace the rotor.
O K NGWheel bearing end play check Refer to GROUP 26 On-vehicle Repair
Service.Refer to GROUP 27 On-vehicleIService.I
Check trouble symptom.
ABS-ECU connector l Disconnect the connector and
measure at the harness side.
l Resistance vaiue between termi-
nals
14-15, and
O KThe sensor harness and connector
should be moved while these checks
are carded out.
OK
Repair
TSB Revision
Repair
.
NG Repair
OK
Check trouble symptom.N G Replace ABS-ECU.
Page 1709 of 2103

ABS
Needle-nosed wire probe .I
I
Connector terminal. arrangement for
troubleshooting
Terminal arrangement shown on the
special tool connector
0 0 0 0 0 0 7 8
ABS-ECU CHECK
TERMINAL VOLTAGE CHECK CHART
1. Connect a needle-nosed to
a voltmeter probe. . .
2. the needle-nosed into each of the
ABS-ECU connector terminals from. the wire side, an d
measure the voltage while referring to the
NOTE
1. Measure voltage with the ABS-ECU
connected.,
2.You may find it convenient to pull out the ABS-ECU to make it easier to reach the connector terminals. :
3.Checks don’t have to be the order
in the chart.
Caution
Short-circuiting the positive probe between a
connector terminal and
could damage the
vehicle wiring, the sensor, ABS-ECU, or three.
care to prevent this!
3.If voltmeter shows any division from standard value , check
the corresponding electrical
wiring, then repair or replace.
4. After
or replacement, recheck with the voltmeter’
to confirm that the repair has corrected the proble m.
ABS-ECU Connector Terminal Arrangement
Caution
Use the special tool to the ABS-ECU
voltage and
2. The ABS-ECU connector terminal
troubleshooting is different from the terminal
arrangement shown on the special tool
So take the readings from the numbers of
the special tool when
Example
TSB Revision
Page 1710 of 2103

ABS Troubleshooting. ,
Terminal No.Check pointCheck condition,
Ignition OFFo v
Rear solenoid valve (Output)
Ignition switch: ON Batterypositive
voltage
Relay power supply (Output) Ignition switch: OFF
o v
2Ignition switch: ON Battery positive voltage
Generator (Input) Ignition switch: ON (while engine is stopped)
2-5
4Ignition switch: ON (while engine is running) Battery positive
voltage
17
F.L. solenoid valve (Output) Ignition switch: OFF
Ignition switch: ONo v
Batterypositive
voltage
18
19
Ignition switch (Input)
F.R. solenoid valve (Output) Ignition switch: ON
Ignition switch: START
Ignition switch: OFF
Ignition switch: ON Battery
voltage
o v
o v
Battery
voltage positive
positive
22
23 Valve relay monitor (Input)
Ignition switch: OFF
o v
Ignition switch: ON
,
Diagnosticcommunication
Scan tool: connected
(Input/Output)tion with the scan
24
Diagnostic selection (Input) Scan tool: disconnectedScan tool: connectedo v
S c a n t o o l : d i s c o n n e c t e d
Approx. 12
25ABS warning light (Output) Ignition ON Battery
voltage positive
29
Stop light switch (Input)
Ignition switch: ON (stop light switch ON) 5 or more
Ignition switch: OFF (stop light switch OFF) 1.5
or more
TSB Revision
Page 1711 of 2103
RESISTANCE AND CONTINUITY CHECK
1. Turn. the ignition switch to OFF.
2. Disconnect the ABS-ECU connector.
3.Measure the resistance and check for continuity bet ween
the terminals of the ABS-ECU connector
while referring to the check chart.
measuring resistance and checking continuity,
a ‘harness for checking contact pin pressure should
be used instead of inserting a test probe.
2.
Checks do not have to be carried out in the order
given
this chart.
Caution
or continuity checks are performed on
the
damage to the
and/or ohmmeter may occur.
care to prevent this!
If the ohmmeter shows any deviation from the norma l
condition, check the corresponding sensor, actuator and
related electrical wiring, and then repair or replace.
5. After repair or replacement, recheck with the oh mmeter
to confirm that the repair or replacement has corre cted
t h e p r o b l e m .
7
sensor switch: OFF
ABS-ECU groundAt all timesContinuity
TSB Revision
Page 1712 of 2103

On-vehicle. Service
Check connector
l
harness
ON-VEHICLE SERVICE
C a u t i o n
Use the specified brake fluid. Avoid using a mixture of
the specified brake fluid and other fluid.
Specified brake fluid:
or
MASTER CYLINDER BLEEDING
Refer to GROUP
On-vehicle Service.
BRAKE LINE BLEEDING
Refer to GROUP
On-vehicle Service.
Caution
For with ABS, be sure to filter/strain the brake
fluid ‘being added to the master cylinder reservoir tank.
Debris may damage the HU.
OPERATION CHECK35200130101
WHEEL SPEED SENSOR OUTPUT VOLTAGE
1. Lift up the vehicle and the brake.
2. Disconnect the ECU harness connector and measure from the harness side connector.
Caution
Set the special tool and use the check connector to
check. Do not connect the connector “(Special
marked with except when recording the waveform
. on’ a test. I n s u c h
connector to the ECU.
3. Rotate the wheel to be measured at approximately
.;
1 rotation per second, and voltage
using a circuit tester or an
Output voltage.
When measuring with a voltmeter:
or more
When measuring with an oscilloscope:
p-p or more
TSB Revision