Page 1345 of 2103
A U T O M A T I C T R A N S A X L E OVERHAUL ,
I
the
. .
,
r e t a i n e r (15
the heads the
I .
i i -
_, ,
, .
, I.
.,
a coating of petrolatum to thrust bearing and
attach to the
carrier.
the planetary carrier.
the forward sun gear, thrust race thrust
bearing
and reverse sun gear.
TSB Revision
Page 1346 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
both sun assembled’ in the previous
into the planetary carrier. .
the reaction brake and brake
TSB Revision
Page 1347 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL
-Transaxle
Identification
markingO.D.I.D.T h i c k n e s s
70.0(2.756)55.7(2.193)1.4
1.8
2.2(0.87).
2.6
66.0 (2.596)54.7(2.126)
1.8
48.9(1.925)37.0(1.457)1
1.2
1.4
2.22.4
48.1(1.906)34.4(1.354)
42.6 (1.677)28.0(1.102)
54.0(2.126)38.7(1.524)
1.6
52.0(2.047)36.4(1.433)
45.0(1.772)28.0(1
46.0(1.811)31(1.220)0.8
52.0(2.047)36.4(1.433)
58.0(2.283)44.0(1.732)
TSB Revision
Identification of thrust bearings, thrust races and thrust washers
mm (in.)
No.
l 2
.
0
,
Page 1348 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
the pressure plate used in disassembly and
install the return spring.
Caution Position the return spring
when installing.
a coating of petrolatum jelly to the wave spring
and attach it to the center support.
the special tool on the center support, install 2
new O-rings and push into the transaxle case.
Caution
Coat the O-rings with automatic
and align the oil holes.
2. Do not move the wave spring out of position
installing.
the snap ring.
TSB Revision
a feeler gauge and measure the end play of the
low-reverse brake. Adjust to the standard value by select-
ing the proper pressure plate.
S t a n d a r d v a l u e : mm in.)
Page 1349 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
the air exhaust plug, and then install the
Air exhaust plug: 33 Nm (24
the anchor rod.
the servo piston and sleeve.’
Caution
The seal ring alignment hole of the
servo
piston must not overlap the oil filler port (indica ted
by the arrow in the diagram).
the special tool to push in the servo piston
and sleeve, and then install a snap ring.
the band.
Caution
Install so the arrow mark
facing forward.
TSB Revision
Page 1350 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
thrust bearing and thrust
rear clutch.
the rear clutch assembly and the front
assembly..
thrust bearing on the rear clutch hub.
I
the rear clutch hub on the
thrust race onthe end of
the rear clutch hub.
TSB Revision
Page 1351 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL Transaxle
thrust bearing in the
. .
the. clutch assembly in the
__
the clutch assembly and drum into
transaxle case at the same time.
. .
I .
.. .
.
thrust race and thrust washer
of the oil pump with petrolatum.
the special tool to new
and oil pump assembly.
Oil pump assembly mounting 21
. ,
TSB RevisionI
Page 1352 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL -Transaxle
end play of the If not the standard
value, replace thrust race and thrust washer
adjust to the standard value.
Standard value: mm in.)
. . . the spacer, idler and then insert
the idler shaft.
Caution
Assemble so that the
groove ‘on
idler gear faces backward. ,
the idler shaft lock together
lock to the specified torque. Bend the three fingers
of the lock plate to prevent turning..
Idler shaft lock bolt: 38
the idler gear cover and a new
Idler gear cover(8
the end clutch shaft from the end with the long
.,
TSB RevisionI