Page 737 of 2103
INTAKE AND EXHAUST Exhaust Pipe and Main
Engine
and Post-installation Operation
139.4
49
6
25
1
443336
33
9.4
16
9.4
--9.4
Main muffler steps
1. Main muffler assembly
2.Gasket3.Muffler cutter
4.Hanger5.Tail hanger6.Rear hanger7. Rear floor heat protector panel
Center exhaust pipe removal steps
8. Heated oxygen sensor connection
9. Center exhaust pipe10.Gasket11.Hanger protector12.Hanger13.Hanger bracket
steps
14.
converter
15. Gasket16. Catalytic converter bracket
1 7 .
18. Hanger Front .20: ‘heat panel
steps
21.
pipe22.Gasket
TSB Revision,
Page 738 of 2103
15-24INTAKE AND EXHAUST Exhaust Pipe Main
Engine
Pre-removal and Post-installationlUnder Cover Removal and Installation
(Refer to GROUP Cover.)
16
13
13
6
9.4
Main muffler removal steps
1. Main muffler assembly
2.Gasket3.Muffler cutter4.Hanger5.Tail hanger6.Rear hanger
7. Rear floor heat protector panel
Center exhaust pipe removal steps
6. Heated oxygen sensor connection9. Center exhaust pipe10. Gasket
11. Hanger protector
12. Hanger
13. Center hanger
steps
14. Catalytic converter
15. Gasket
16. Front floor. heat protector panel
Front exhaust steps
1 7 . F r o n t .18. -Gasket19. Hanger20. Front hanger
TSB Revision
Page 739 of 2103
INTAKE AND EXHAUST Exhaust Pipe . .
Engine>
Post-installation OperationlUnder Cover Removal and Installation
(Refer to GROUP Cover.) ,
3.4
9.4
139.4
9.449N m
36 bs.
-59 Nm
q 2
9.4
Main muffler
removal steps
1. Main muffler assembly
2. Gasket
3. Hanger
4. Tail hanger
5. Rear hanger
6. Rear floor heat protector panel
Center exhaust pipe removal steps 7. Heated oxygen sensor
connection exhaust pipe
Hanger protector11. Hanger
12. Hanger bracket
9.49.4
1
Catalytic converter removal steps
13. Catalytic 14. Gasket15. Catalytic bracket
16. Hanger protector
17. Hanger
18. Front hanger
19. Front floor heat protector panel
II3344N m334936
Front exhaust pipe removal steps
20. Heated oxygen sensor
21. Front exhaust pipe22. Gasket
TSB Revision
Page 740 of 2103
INTAKE AND Pipe and Main
Engine (Non-turbo)>
Engine (Turbo) and
REMOVAL SERVICE POINT
HEATED OXYGEN
OXYGEN SENSER
For Engine (Non-turbo), ‘the’ exhaust threabs
must be cleaned with an 18 mm in.) 1.5
the heated oxygen sensor has been disconnected.
INSTALLATION SERVICE
HEATED OXYGEN SENSOR
OXYGEN SENSER
If reusing the original sensor, with
an antiseize compound such as
New sensors have compound on do not
require an additional coating.
TSB Revision
TSB Revision
Page 741 of 2103

CONTENTS
AUTO-CRUISE CONTROL SYSTEM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
AUTO-CRUISE CONTROL* . . . . . . . . . . . . . . 40
GENERAL INFORMATION . . . . . . . . . . . . . . . . 7
ON-VEHICLE SERVICE. . . . . . . . . . . . . . . . . 33
Auto-cruise Control Cable Check and
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Auto-cruise Control Component Check . . . . . 37
Auto-cruise Control System Operation Check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
SERVICE SPECIFICATIONS . . . . . . . . . . . . . 8
SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . 8
TROUBLESHOOTING
ENGINE (NON-TURBO)> . . . . . . . . . . . 9
TROUBLESHOOTING
(TURBO) AND ENGINE> . . . . .
EMISSION CONTROL’ SYSTEM
. . . . .
CATALYTIC . . . . . . . . . . . . . .
General Information . . . . . . . . . . . . . . . . . . 57
EVAPORATIVE EMISSION .
SYSTEM. . . . . . . . . . . . . . . .
Air Conditioning . . . . . . . . . . . . . . . . . . . 52
Component Location
. . . . . . . . . . . . . . . . . .
Engine Coolant Temperature Sensor
Intake Air Temperature Sensor . . . . . . . . . . . . 52
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRA INT SYSTEM (SRS) EQUIPPED
WARNING!
(1) Improper serviceor maintenance of any component of the or any SRS-related can to injuryorcleathtoservicepersonnel (from inadvertentfiring the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly rev iew this manual, and especially its GROUP
Restraint System (SRS) and GROUP 00 Maintenance Service, before any service or maintenance of any
componentof the SRS or any SRS-related component.
NOTEJhe includes the following components: warning light, air bag module, clock components (that may have to be removed/installed in connection with or areIndicated in the table of contents by an asterisk
Page 742 of 2103

17-2
Evaporative Emission Canister/Air Filter/
Evaporative Emission Ventilation Solenoid
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Evaporative Emission Purge Solenoid
Check. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . .
General Information. . .. . .. . . . . . . . . . . . . . .
Purge Control System Check. . . . . . . . . . . . .
Purge Port Vacuum Check. . . . . . . . . . . . . . . .51
EXHAUST GAS (EGR)
SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Component Location. . . . . . . . . . . . . . . . . . . . .54
EGR Port Vacuum Check. . . . . . . . . . . . . . . . .56
EGR System Check. . . . . . . . . . . . . . . . . . . . . .55
EGR Valve Check. . . . . . . . . . . . . . . . . . . . . . . .55
Electric EGR Transducer Solenoid Check
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
General Information. . . . . . . . . . . . . . . . . . . . . .54
GENERAL INFORMATION. . . . . . . . . . . . . . .44
POSITIVE CRANKCASE VENTILATION
SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Component Location. . . . . . . . . . . . . . . . . . . . .48
Crankcase Ventilation System Check. . . . . .49
General Information. . . . . . . . . . . . . . . . . . . . . .48
Positive Crankcase Ventilation Valve
Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
SERVICE SPECIFICATIONS. . . . . . . . . . . . .45
TROUBLESHOOTING’
. . . . . . . . . . . . . . . . . . .45
VACUUM HOSES. . . . . . . . . . . . . . . . . . . . . ..4 8
Vacuum Circuit Diagram. . . . . . . . . . . . . . . . . .47
Vacuum Hose Routing
. . . . . . . . . . . . . . . . . . . .46
CONTROL SYSTEM
ENGINE (TURBO) AND
ENGINE>. . . . . . . . . . . . . . . . . . . . . 6 0
CATALYTIC CONVERTER. . . . . . . . . . . . . . .89
General Information. . . . . . . . . . . . . . . . . . . . . .89
EVAPORATIVE EMISSION CONTROL
SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69’
Air Conditioning Switch
. . . . . . . . . . . . . . . . . . .77
Component Location Engine (Turbo)>
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
Component Location Engine (Turbo)>
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
Evaporative Emission Canister/Fuel Tank
Pressure Relief Valve/Purge Control Valve
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Evaporative Emission Purge Solenoid
Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
General Information Engine (Turbo)> G e n e r a l I n f o r m a t i o n
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .70
Purge Control System Check
. . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . .71
Purge Control ‘System
(Purge Flow Check) Engine>. . . . . . .73
Purge Control Engine (Turbo)>
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Purge Port Vacuum Check. . . . . . . . . . . . . . . .75
Volume Air Flow Sensor, Engine Coolant
Temperature Sensor and Intake Air
Temperature Sensor. . . . . . . . . . . . . . . . . . . . . . .77
RECIRCULATION (EGR)
.... . .. . . . . . . . . . . . . . . . . . . . . . . .81
Component Location. . . . . . . . . . . . . . . . . . . . .82
EGR Port Vacuum Check . . . . . . . . . . . . . . . . .86
EGR Solenoid Check Engine (Turbo)>
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
EGR Solenoid Check Engine>. . . . . .
EGR System Check . . . . . . . . . . . . . . . . . .
EGR Valve Check. . . . . . . . . . . . .. . .
General Information... . . . . . . . . . . . . .....81
Vacuum Control Valve Check
. . . . . . . . .
.......................................
POSITIVE CRANKCASE VENTILATION
SYSTEM
. . . . . . . ... . .. . . . . . . . . . . . . . . . . 65
Component Location. . . . . . . . . . . . .. . . . . . . . .66
Crankcase Ventilation. System . .67
General Information
. . . .. . . . . ... . ........
Positive Crankcase Ventilation Valve
Check. . . . . . . . . . . . . . . . . . . . . ... . ............
SERVICE SPECIFICATIONS. .. . . . . . . . . 60
SPECIAL TOOL . . . . . . . . . . . . . . . . . . . . . . .
. . .. .
HOSES
. . . . ..
. . . . . . . . . . . . . . . . . . . . .,
Circuit Diagram.. . . . . . . . . . . . . . . . . . ,
Vacuum Hose Routing. . . . . . . ...... . . . 6 1
ENGINE CONTROL
3
ACCELERATOR
......
GENERAL INFORMATION . . . . . .. . . . . . . . . .3
ON-VEHICLE SERVICE. . . . . . . . . . . .4
Accelerator Cable Check and
Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATION. . . . . . . . . . . . . . .3
. ... . . . . ...3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
Page 743 of 2103
ENGINE AND EMISSION CONTROL Engine Control System
GENERAL INFORMATION
A c a b l e - t y p e a c c e l e r a t o r m e c h a n i s m a n d asuspended-type pedal have been adopted.
SERVICE SPECIFICATION
I Item Standard valueI
Accelerator cable play mm (in.)
TROUBLESHOOTING
Symptom Probable cause Remedy
Throttle valve will notMisadjusted accelerator cable
Adjust
fully open or close Misadjusted auto-cruise control cable Adjust
Broken return spring
Replace
Throttle lever malfunction Replace I
Accelerator pedal op-
Accelerator pedal wrongly tightened Repair
eration not smooth (over acceleration)
accelerator cable. Repair
Accelerator cable requires lubrication Lubricate or replace
Revision
Page 744 of 2103
ENGINE AND EMISSION CONTROL Engine Control
ADJUSTMENT
For models equipped with the auto-cruise
refer to
1. Turn and lights OFF.
Inspect and adjust”
no load.
2. Warm engine until stabilized at
3. Confirm idle at
4. Stop engine (ignition switch OFF).
5. Confirm there are no in
6. Check cable for correct slack:
7.If there is too much
the following procedures.
(1) Turn the ignition switch to ON position (without
starting the
in that condition
motor.’ , ,
4.93.6
TSB Revision
(2) Loosen the adjusting bolt release the cable.
(3) After moving the plate
before the throttle lever starts to
plate back towards the throttle
value amount to biing accelerator cable play
to standard value. .
Standard value: mm in.)
(4) Tighten the adjusting bolts to the specified to rque.
8. Adjust accelerator cable play and confirm thrott le lever
stopper touches the fixed SAS.