Page 1865 of 2103

BODY Door
with e n t r y s y s t e m > ,
Central door lock switch continuity check (Refer to ,l ReplacelDoor lock power relay continuity check (Refer to lDoor lock power relay 2 continuity check (Refer to
OK
Measure at the door lock power relay 1 connector and the Check the ‘the fusible and the; door lock power relay 2 connector power relay 1, and link and door
Disconnect the connector and measure at harness sid e.
Voltage between terminal (7) and ground power relay 2. if necessary.
OK: Battery positive voltage
(2) Continuity between terminal (2) and ground
OK: Continuity
OK
Check harness the door lock power 1 the
ground, and the door relay ground.
Repair, if necessary.
Measure at the door lock switch connector (L.H.) and Check the harness between the door(R.H.)Disconnect the connector and measure at harness sid e. L.H.: Voltage between terminal (I), (4) and ground door lock power relay 2. Repair; if OK:
Battery positive voltage Check the harness between the door lock switch and the ground. . Voltage between terminal (5) and ground
Repair, if necessary.
OK: Battery positive voltage
(2) L.H.: Continuity between terminal (2) and groun d
OK: Continuity
Continuity between terminal (7) and ground
OK: Continuity
OK
NG Replace
OK
Check the harness between the door lock actuator an d the door
lock power relay and between the door lock actuator and the
door lock power relay 2. Repair, if necessary.
TSB Revision
Page 1866 of 2103

42-42BODY Door
When the driver’s side door lock is turned with the key if the driver’s inside
knob is operated, another door is not locked.
.
Check the scan tool input signal
Actuator switch (driver’s side) input signals
OK:The scan tool buzzer sounds once when actuator swit ch (driv-er’s side door) is unlocked.
NG
Door lock actuator check N G Replace
NG
and Repair
Check trouble symptom.
NG NG
Repairswitch(driver’s side).
OK
Check the harness between the actuator switch (driv er’s side) andthe ground. Repair, if necessary.
When the driver’s side door lock is turned with key , another door is not unlocked.
OKCheck the scan tool input signalCheck the harness between the door power relay and the
Key cylinder switch (driver’s side) input signalsETACS-ECU.OK:The scan tool buzzer sounds once when key cylinder switch(driver’s side door) is LOCK or UNLOCK.
NG
Door lock key cylinder switch to
TSB Revision
OK
NG Repair and
Check trouble symptom.
OK
NG
Check the harness between the ETACS-ECU and the ke v NG
switch (driver’s side)., ,
OK
Check the harness between the key cylinder switch ( driver’s side)
and the ground. Repair, if
Page 1867 of 2103

BODY
the passenger’s side door lock is turned with
NGDoor lock key cylinder SW(Refer to . .
NGCheck the following Repair.
and .
OK
Check trouble symptom.. .
NGN GMeasure at the key cylinder switch (passenger’s sid e) connector Check the harness between the side) and the door lock power .
Disconnect the connector and measure at harness sid e. between terminal (3) and groundOK:Battery positive voltage .
OK
Check the harness between the key cylinder switch (
passenger’s
side) and the ground. Repair, if necessary.
KEY REMINDER SYSTEM
INSPECTION CHART FOR TROUBLE SYMPTOMS
T r o u b l e s y m p t o m
Probable cause
If the driver’s side inside lock knob is lBroken wire in input circuit in door
locked under the following conditions, the switch.
Chart A
door can not be locked:l Door switch is faulty.
lThe key is inserted in the ignition key l
cylinder..
lThe driver’s side door is closed.
If the driver’s side inside lock knob ‘is lBroken wire in input circuit in Check
locked under the following conditions, the
switch.
door will be locked:l
Door switch is faulty.(Refer-to
lThe key is inserted in the ignition key l
cylinder.l
Broken wire in input in key
lThe driver’s side door is opened.reminder switch.l ETACS-ECU is faulty
If the driver’s side inside lock knob is
Check accordingto
locked under the following conditions, the reminder switch.
door can not be locked:lKey reminder. switch is faulty.(Refer to
lThe key is removed from the ignition l
key cylinder.lThe driver’s side door is opened.
TSB Revision
Page 1868 of 2103

BODY
T R O U B L E S Y M P T O M I N S P E C T I O N
A If the driver’s side inside lock knob is under the following conditions, the door not
locked:
lThe key is inserted in the ignition key cylinder.
l The driver’s side door is closed.
Door switch continuity check
(Refer to
NG Replace
Measure at the door switch connector
Disconnect the connector and
measure at harness side
l Continuity between terminal (2)
and around
OK:
OK
the ETACS-ECU
NG
Disconnect the connector and
measure at harness side
(Door switch: OFF)
l Continuity between
(13)
OK: No continuity
Replace the ETACS-ECU
If the driver’s side inside lock knob is locked und er the following conditions, the door will be locke d:
l The key is inserted in the ignition key cylinder.
l The driver’s side door is opened.
NG Replace Switch.)
Door switch continuity (Refer to Replace
Measureatthe
.
Disconnect the connector and
measure at harness side
. Voltage between terminal (6) and
groundOK: Approx.
TSB Revision
Measure at the ETACS-ECU connector
.
Disconnect the connector and
measure at the side (key reminder switch OFF)
. Continuity between terminal (17)
and ground
OK: No continuity
NGCheck the harness between the key ETACS-ECU. if
Measure the door switch connector
Voltage between terminal (2) and
OK
Check trouble symptom.
NG
Replace the ETACS-ECU
Page 1869 of 2103
BODY Door
If the driver’s side inside lock knob is locked under the following conditions, the door can not
locked:lThe key is removed from the ignition key cylinder.
lThe driver’s side door is opened.
and
minder switch and the ETACS-ECU.
Replace the ETACS-ECU.
OK
NG Check the connectors:
between (4)
OK
Check trouble symptom.
N G
and
Replace the ETACS-ECU
TSB Revision
Page 1870 of 2103

BODY Door
GLASS AND DOORS
SymptomProbable causeR e m e d y
Water leak through Incorrect window glass installation
Adjust position
door window glass Gap at upper window glass Adjust position
Door window Incorrect window glass installation
Adjust position
malfunction
Damaged or faulty regulator Correct or replace
Water leak throughCracked or faulty weatherstripReplace
door edge
Water leak from doorDrain hole clogged
Remove foreign objects
centerInadequate waterproof film contact or damageCorrect or replace
Door hard to open Incorrect latch or striker adjustment
Adjust
Door does not open Incorrect door installation Adjust position
close completely
Defective door check strap Correct or replace
Door check strap and hinge require grease Apply grease
Uneven gap betweenIncorrect door installationAdjust position
Wind noise around
door
Weatherstrip not holding firmly Adjust fit of door
Improperly installed weatherstrip or setting of Rep
air or replace
weatherstrip
Improperly closed door Adjust
Improperly fit door Adjust
Improper clearance between door glass and door Adjust
weatherstrip holder
D e f o r m e d d o o rRepair or replaceI
TSB Revision
Page 1871 of 2103

BODY Door
Ex. Noise produced here
HOW TO LOCATE
(1) Attach cloth tape to every such as panel seams,
projections, molding seams, glass and body seams, etc.
which might conceivably be the source of wind noise.
(2) Then make a road test to check that the places n ot covered
by tape are not sources of wind noise.
(3) Then remove the strips of tape one by one, making a
road test after each is removed, ‘until a wind noise source
i s d i s c o v e r e d .
(4) When such a place is found, cover it again and repeat
the procedure to check if there are any other noise source.
(5) If no others are found, the’ last tape the
only source.
(6)Cut the remaining piece of tape into attach
it again as it was before,’ and then remove the pieces
one by one to narrow down’ the source.
(7) Check to confirm that wind noise occurs when th e last
remaining tape is removed, and that noise does not occur
when it is re-attached.
(8) When the source(s) of the wind noise is finally located,
attach butyl tape, body sealer or similar material to obstruct
this source as much as possible.
Page 1872 of 2103

42-48BODY Door
Delta sashInner stabilizer
track
ON-VEHICLE SERVICE
DOOR FIT ADJUSTMENT
1.Use the special tool to loosen the hinge mounting b
olts
o n t h e b o d y
2. When there is a stepped section in the door and body,
use the special
loosen the door hinge mounting
bolt on the door side and adjust the door fit.
Caution
Attach protection tape to the fender. edges
the
hinge is installed.
3. If the door is hard to open or close, use the sh im or
move the striker up and down or left and right to a djust
the linking of the striker and the door latch.
DOOR WINDOW GLASS ADJUSTMENT 423001001~0
1. Remove the door trim and waterproof film. (Refer to
2. Remove the drip line weatherstrip.
(Refer to
3. Loosen the bolts and nuts of parts.
l Delta sash
l Equalizer arm bracket
l Glass guide front track
l Glass guide rear track
. u p - s t o p
l Inner stabilizer
NOTE
Move the window glass down to the lowest position b efore
removing the delta sash bolt.
4.Lower the door window glass fully. a feeler gage
with a thickness of
mm in.) ‘between the
glass stabilizer (nylon fiber the belt line molding
and the glass.
Adjust the two bolts so that the inner stabilizer i s pressing
against the glass, and then tighten the inner stabi lizer
nuts.
5.Raise the door window glass, and adjust it so that the
following dimensions are at the standard value.
TSB Revision