Page 1849 of 2103
BODY Windshield and Window
(4) After
and onto the body
Remove the adhesive
b o d y
clean.
(6) After the
to until the adhesive
C a u t i o n
When using an infrared lamp or other means for quick-
er hardening, keep the surface temperature
or lower.
(7) After about 30 minutes or more following bondin g of the
quarter glass to the body, check for water leaks.
Caution
1. If the vehicle is to be moved, do so gently.
2. When
for water leaks, do not squeeze
the
end.
TSB Revision
Page 1850 of 2103
BODY Windshield and Window Glass
QUARTER WINDOW GLASS AND REGULATOR ASSEMBLY
REMOVAL AND INSTALLATION
IPost-installation OperationQuarter Window Glass Adjustment (Refer to I
122820
Power window switch removalsteps
1. Door trims (Refer to GROUP 42 Door.)2. Power window switch
Quarter window glass removalsteps
l Quarter trim, lower
(Refer to GROUP Trims.) Quarter belt moulding (Refer to GROUP
3. Quarter trim bracket
4. Quarter belt line inner weatherstrip
and quarter window front weather-
strip
5. Waterproof film
window glass assembly
Quarter window glass
9. Guide assembly
Regulator assembly removal steps
6. Quarter window glass assembly l Rear speaker bracket A
(Refer to GROUP 54 Speaker.)10. Regulator assembly
TSB Revision
Page 1851 of 2103
BODY Windshield Window
Section A A
QUARTER GLASS ASSEMBLY
REMOVAL
(1) lower the quarter window
(2) the waterproof film.
(3) Disconnect the ball joint of from
quarter window glass through ,
Disconnect connector, from
INSTALLATION SERVICE POINT
QUARTER WINDOW GLASS ASSEMBLY
INSTALLATION
Set the length of the adjusting stud to the dimension shown
in the illustration to make adjustment of the quart er window
glass easier.
INSPECTION
POWERWINDOW MOTOR CHECK
(1) Check that the motor runs smoothly when the bat tery
is connected directly to the motor terminals.
(2) Furthermore, check that the motor operates in r everse
when the terminal connections are switched.
TSB Revision
Page 1852 of 2103
BODY Windshield and Window Glass
Power window
switch (Quarter
windowPower window
Connector A Connector
POWER WINDOW SWITCH CONTINUITY CHECK
Main switch Quarter Window Glass>
Switch position
OFF
Terminal
No. of
connector A
2
0
Terminal No. of
TSB Revision
Page 1853 of 2103
BODY Windshield. and Window
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Removal and Installation
l Rear Wiper Arm(Refer to GROUP 51 Rear Wiper and Washer.)l Upper Trim, Lower Trim and Side Trim (Refer to GROUP Trims.)l High-mounted Stop Light without rearspoiler, (Refer to GROUP 54 High-mounted Stop
Light.)
Adhesive tape:
or equivalent
Section C-C24
Section
Section D-D
mm (in.). .
Adhesive:
ATD Part No. Super Fast Urethane and ATD Part No. 8608 Super Fast Urethane prim& equivalent
Removal steps
Harness connector 3. m o l d i n g
2. g l a s s Dual-lock fasteners
TSB Revision
Page 1854 of 2103
BODY Windshield and Window Glass
mm (in.)Dual-lock fastener
installation position
Section A-A R E M O V A L S E R V I C E P O I N T
GLASS
Remove the same way as the windshield. to
INSTALLATION SERVICE POINTS
DUAL-LOCK FASTENER INSTALLATION
After making sure that there are no bends or raised
sections
in the dual-lock fasteners, attach the dual-lock fasteners to
the notches in the body as shown in the illustratio n.
MOLDING INSTALLATION
Apply specified double-sided to the glass in the places
shown in the illustration, and then install the molding.
Specified adhesive tape:
ATD Part No. 6382 or equivalent
TSB Revision
Page 1855 of 2103
BODY Windshield and Window
Glass side molding
Body side
imer
Section B-B
Section C-C
mm (in.)
TSB Revision
GLASS INSTALLATION
(1) a sponge in the primer, and apply evenly to the
glass and the body in the places shown in the illus tration.
Specified primer:
ATD Part No. 8608 Super Fast Urethane
or equivalent
Caution
1.Apply the primer evenly around the entire circum-
ference, because it strengthens the adhesive.
Otherwise, a too thick application will cause lower -
ing of the adhesive strength.
2.
not touch the coated surface.
(2) After applying the primer, let it dry for 3 to 30 minutes.
(3) Within 30 minutes after applying the primer, us e a sealant
gun to apply the adhesive evenly over the adhesion sur-
face of the vehicle body. (Refer to
Specified adhesive:
Part No. 8609 Super Fast Urethane or
equivalent
NOTE
Cutthe nozzle tip of the sealant gun into a shape
to facilitate adhesive application.
Page 1856 of 2103
BODY Windshield and Window Glass(4) After
the mating marks, press the gently
and evenly so that it adheres completely.
After completion of this operation’ the
glass), place it somewhere where it disturbed,
until the adhesive sets.
Caution
When using an infrared
or other for quick-
er hardening, keep the surface temperature
or lower.
After attaching the glass to the body, let it stand for 30
minutes or more, and then test for water
Caution
1. If moving the vehicle, it should done gently.
2.When testing for water leakage, do not pinch the
end of the hose to spray the
TSB Revision