Page 2057 of 2103

HEATER, AIR
AND VENTILATION On-vehicle Service
IDLE-UP OPERATION CHECK
1,Before inspection and adjustment, set the f&w-
ing condition:
lEngine coolant temperature:
lLights, electric cooling fan and accessories: Set t o
OFF
lTransmission: Neutral (N or for vehicles with
l Steering wheel:
2. Check whether or not the idling speed is the sta ndard
value.
Blower relay
Standard value:
100
Engine (Turbo) and Engine>
100 Engine (Non-turbo)>
3. When the
is running after turning the A/C switch
to ON, and the blower switch to the MH or HI positi on,
check to be sure that the idle speed is at the stan dard
value.
Standard value: (in Neutral)
NOTE
Idle speed is controlled by the system and is not
adjustable. If, idle speed is not within specifications, check
the system.
Engine (Non-turbo)>: Refer to GROUP On-
vehicle Service.)
Engine (Turbo)>: Refer to GROUP On-vehicle
Service.)
Engine>: Refer to GROUP On-vehicle Ser-
vice.)
POWER RELAY CHECK
BLOWER MOTOR RELAY CHECK
Battery voltage Terminal No.III
1235
Power is not supplied
Power is supplied0 0
0 0
Page 2058 of 2103
Engine (Turbo)>HEATER,
AIRAND VENTILATION On-vehicle Service
A/C COMPRESSOR CLUTCH RELAY, CONDENSER FAN
RELAY (LO) AND (HI) CONTINUITY CHECK
Batteryvoltage Terminal No.
13 45
Power is not supplied0
Engine (Non-turbo)>
Condenser
fan relay (LO)
Engine>
NC
clutch relay
ment relay box
Power is supplied0
TSB Revision
Page 2059 of 2103
HEATER, AIR
AND VENTILATION Heater
HEATER CONTROL ASSEMBLY
REMOVAL AND INSTALLATION
When and the floor console as-
let it
orthecomponents.
NOTE metal clip positions.
Removal steps
1. Center panel
2. Floor console (Refer to GROUP
Floor Console.)
3. Radio, tape player and CD player (Refer to GROUP
Radio,
Tape Player, CD
Speaker and Antenna.)
4. Stopper
5. Heater control assembly
TSB Revision
Page 2060 of 2103

AIR ,
AND VENTILATION Heater
R E M O V A L
HEATER CONTROL REMOVAL
(1)Press the lever pin to disconnect the air outlet changeover
damper cable.
(2) Snap the boss and clamp with nippers or a flat- tipped
screwdriver, etc to remove the heater control assem bly.
NOTE
The boss and clamp are needed for assembly line at
the factory, but not needed for service work.
INSTALLATION SERVICE POINTS
HEATER CONTROL ASSEMBLY INSTALLATION
(1) Always snap the boss and clamp before installin g a new
heater control assembly to the instrument panel.
NOTE
The boss and clamp are ‘needed for assembly line at
the factory, but not needed for service work.
(2) Set the temperature control knob on the heater control
assembly to MAX HOT.
(3) Set the air mix
lever. at, the upper part of the
heater unit to the MAX HOT position, install the cable
to the lever pin.
(4) Push the outer cable in the direction of the ar row so
that there is no looseness, and then ‘secure it wit h the
clip.
,
(5) Set the knob for the air outlet changeover on the heater
control assembly to the DEF position.
(6) Set the air outlet changeover damper lever of t he heater
unit to DEF position and install the cable to the lever
pin.
(7) Push the outer cable in the direction of the ar row so
that there is no looseness, and then secure it with the
clip.
TSB Revision
Page 2061 of 2103

Air-recirculation position
HEATER, AIR
AND VENTILATION Heater Control Assembly
(8)Set the lever for the inside/outside air changeover
the heater control assembly to the air-recirculatio n posi-
tion.
(9) Set the inside/outside air changeover damper le ver of
the blower unit to air-recirculation, position (with the inside/
outside air changeover damper lever touched to the stop-
per of the blower case) and install the cable to the lever
the outer cable in the direction of the arrow so
that there is no looseness, and then secure it with the
.
clip.
INSPECTION
Check each knob and lever for proper operation and
possible damage.
lCheck the connection between the lever and cable.
lCheck that the cable sides properly.
Check the illumination light for a possible broken filament.
BLOWER SWITCH CONTINUITY CHECK
Switch Terminal No.I
12 3 4 5 6 7 8
OFF I I I
.0 0
0
TSB Revision
DEFROSTER SWITCH CONTINUITY CHECK
Terminal No.Air outlet changeover control knob 1
DEF,
Other than the above
00
Page 2062 of 2103
55-22HEATER, AIR
AND Heater Control
DISASSEMBLY AND REASSEMBLY
damper cable
Disassembly steps
1.Knob2.Lever assembly3. Air conditioning switch
4.Knob assembly5. Bulb and socket assembly6.Defroster switch7. Air outlet changeover damper ca-
ble8. Air mix damper cable
9. Inside/outside air changeover10. Control base assembly
11. Knob assembly A
12.Panel case
13.Nut14.Control base15.Blower switch
NOTE
Parts from No. 11 to No. 14 are not supplied as sin gle
parts.
DISASSEMBLY SERVICE POINT
AIR OUTLET CHANGEOVER DAMPER
CABLE/AIR MIXING DAMPER CABLE/INSIDE/OUTSIDE AIR CHANGEOVER DAMPER
CABLE REMOVAL
a flat-tipped screwdriver to disengage the claws, and
then remove the cables.
Page 2063 of 2103
HEATER, AIR
AND VENTILATION Air Conditioning Switch
AIR CONDITIONING SWITCH
REMOVAL AND INSTALLATION
Removal steps
1. Stopper 2. Center air outlet3. Center panel4. Air conditioning switch
indicates sheet metal clip positions.
I Revision
INSTALLATION POINT
CENTER AIR OUTLET INSTALLATION
(1)Turn the cool air bypass lever of the center air outlet
fully downward.
(2) Pull the cool air bypass damper lever on the he ater unit
side all the way toward you, and then connect the c able
to the lever pin.
(3) Push the outer cable in the direction of the ar row so
that there is no looseness, and then secure it with the
clip.
INSPECTION
AIR CONDITIONING SWITCH CONTINUITY CHECK
Page 2064 of 2103
HEATER, AIR
AND VENTILATION Heater Unit and Heater Core
HEATER UNIT AND HEATER CORE
REMOVAL AND INSTALLATION
Post-installation OperationRefilling CoolantWhen and installing the floor console from vehicles equipped with SRS, do notlet it bump against the ECU or the components.
TSB Revision
Removal steps
l Instrument panel (Refer to GROUP
Instrument Panel.)1. Heater hose connection2. Center stay
3. Center duct
4. Semi rear heater duct
5. Foot distribution duct
6. Cooling unit installation bolt and nut
7 . C l i p
8. Heater unit
9. Heater core