Page 1217 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL Special Tools,
Super-session ,
Alignment of oil ‘pump housing and reaction
s h a f t
Tool Tool numberand
name
Guide pin
Spring
compressor
Spring
compressor
servo
set
-01
adapter
puller
ringnstaller
10998812
nstaller cap service
Use
Disassembly clutch
installation of servo
Removal and installation of transfer
shaft
of bearing
Assembly of the end clutch
of
. .
with installer and installer adapter
TSB Revision
Page 1218 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL Tools
Tool
of each bearing
TSB Revision
Page 1219 of 2103
AUTOMATIC
OVERHAUL __
TSB Revision.
. .
Page 1220 of 2103
4AUTOMATIC Transaxle
TRANSAXLE
16
18
16
1.Torque converter
2.Converter housing3.Gasket4.Oil pump5.O-ring6.Gasket7. Thrust washer 6. Front clutch assembly 9. Thrust race
10. Thrust bearing
11. Thrust washer
12. Rear clutch assembly
13.Spacer
14.Outer race
Differential16. Thrust bearing 17.Clutch hub
18. Thrust race
19. Thrust bearing 20. band
21. drum
22.Snap ring
23.Center support24.O-ring
25.Wave spring
26.Return spring
27.Pressure plate
28.Brake disc
29.Brake plate
30.Reaction plate
31. Reverse sun gear
32. Thrust bearing
33. Thrust race
34. Forward sun gear35.Planetary carrier
36. Thrust bearing
TSB Revision
Page 1221 of 2103
39.
40.
41.
44:
45.
46.
47.
50.
51.
52. 53.
Pulse generatorSpring washerControl lever
ClampPark/neutral position switch
Oil temperature sensor
End clutch cover
O-ring
BearingEnd clutch
Thrust washer
End clutch hub
Thrust bearing
End clutch shaftBearing retainer
Snap ring Lock plate
54. Idler gear shaft55. Bearing inner race’
56. Idler gear
57. Bearing inner race
58. Spacer
59. Snap ring .60. servo switch
61. servo piston
62. Spring
63. Anchor rod64. flange
65. Transfer shaft
66. Outer race
67. Gasket . .
,
68. O-ring
6 9 . V a l v e b o d y
TSB Revision
Page 1222 of 2103

6AUTOMATIC TRANSAXLE
OVERHAUL Transaxle
70. Clamp
71.
Gasket
72. Oil pan
73.
Gasket
74.Drain plug
75.O-ring
76.Set screw77.O-ring78.Detent plate
79. Sprag rod support
80. Parking sprag rod
2170046
81.Control shaft
82. D-ring
83. Transfer shaft cover
84.Lock nut
85. Driven gear
86.Outer race
87.Spacer
-88.Outer race89.Transaxle case
(1) Prior to disassembling the transaxle, openings
and thoroughly clean the exterior of the, assembly, prefer-
ably by steam.
(2) Place the transmission on the ‘workbench with t he oil
pan down.
(3) Remove the torque converter.
.
(4)Measuring input shaft end play will
usually indicate when a thrust is required
(except when major parts are replaced). Thrust wash ers
are located between the shaft support and rear
clutch retainer, and between the reaction shaft sup port
and front clutch ‘retainer.
Mount a dial indicator to the converter housing usi ng
the special tool, with its plunger seated against t he end
of the input shaft.
Move the input shaft in and out with pliers to obta in the
end play reading. Be careful not to scratch the inp ut shaft.
Record the indicator reading for reference when rea ssem-
bling the transaxle.
(5) Remove pulse generators “A” and “B”.
(6) Remove the manual control lever, and then remov e
park/neutral position switch. ,
.
TSB Revision
Page 1223 of 2103
A U T O M A T I C T R A N S A X L EOVERHAUL Transaxle
the snap ring and remove
switch.
(8) Remove the oil pan and oil gasket.
(9) Remove the oil filter.
the oil temperature sensor bracket. mounting
bolts’and remove the oil temperature sensor from brack-
et. Using a screwdriver, push out the rubber plug,
from inside the case, and remove the oil temperatur e
sensor from the case..
(11) With their catches pressed down, force the har
ness grom-
met and connector into the transaxle case:,
TSB Revision
Page 1224 of 2103
8A U T O M A T I C T R A N S A X L E ’
OVERHAUL Transaxle
the valve body mounting bolts indicated by
aiid the valve. body from the transaxle
the end clutch
.
the end clutch
.
thrust washer from the end.
.
the end clutch hub and the thrust
TSB Revision