Page 1337 of 2103
AUTOMATIC TRANSAXLE
O VE R H A U L
the band.
the servo coyer snap ring. Then
the servo switch.
the special tool, push in the
remove the snap ring.
the servo piston.
the anchor rod.
TSB Revision
Page 1338 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
the plug, then remove the exhaust plug.
the snap ring.
the special tool, remove the center
the reverse sun gear forward gear to-
gether.
the assembly.
TSB Revision
Page 1339 of 2103
TRANSAXLE
OVERHAUL -Transaxle
the wave spring, return spring, reaction
brake discs, and brake plates.
the and the rear bearing;
,
__
49
the snap ring-and then remove output flange
assembly.
the output bearing
then remove the output bearing retainer, and outer
a rod 8 mm in.) in diameter and
in.) in length from the the figure
out the rear shaft. ,
Revision
Page 1340 of 2103
OVERHAUL,, . . ,
special tool,
into the center and,
that bolt, remove the retainer and
race.
.
the center bearing
remove the ring and put a
puller or similar tool in the viscous
p u l l o u t t h e v i s c o u s . .
.
,,
the front bearing retainer bolt
Then, screw a bolt into the threaded hole the
front bearing retainer and,
that remove
front bearing retainer and race. ,
Page 1341 of 2103
AUTOMATIC TRANSAXLE.
OVERHAUL Transaxle
59
I I I
front
I
a sliding or tool, remove
race.
the oil , .
,
REASSEMBLY
(1) Using the special tool, install the oil differential
bearing retainer and transaxle ‘case.
.
(2) Using- the special tool, install the
seal.
TSB Revision,
Page 1342 of 2103

A U T O M A T I C T R A N S A X L E
OVERHAUL Transaxle
(3)Using the special tool, press-fit the outer race in the trans-
axle case.
(4) Install the front output shaft assembly.
(5) Place solder with a length of approx. 10 mm in.)
and a diameter of 1.6 mm
in.) on the front bearing
retainer in the shown positions and then install’ t he outer
race.
(6) Install the front bearing retainer and tighten the bolt to
the specified torque.
Front bearing retainer mounting bolts:. 49 Nm (35
(7) Loosen the bolts and remove the front bearing r etainer.
(8) Remove the outer race from the front bearing
and remove the solder. If the solder does not break , per-
form the work in steps 5-8 with large solder.
Measure the thickness of the crushed solder
a ‘mi-
crometer and select a spacer with the correct thick ness
so the preload reaches the standard value. .
Standard value:
m m
(9) Install the spacer selected in the previous ste p and the
outer race in the front bearing retainer.
(lO)First install the front bearing retainer and ap ply sealant
to the bolts and then tighten to the specified torq ue.
Specified sealant:
Stud Locking Part No. 4170 or
Front bearing retainer mounting bolts: 49 Nm (35
TSB Revision
Page 1343 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
a bearing puller, support the viscous coupling and
insert in the case. Then, the stopper ring.
the special tool, install the outer race in the
bearing retainer..
the center bearing retainer stopper
bearing retainer stopper bolt: 5 Nm (4
the center bearing retainer so the projection of
the stopper bolt fits in the groove of the center b earing
retainer.
the special tool in the center differential and install
the center differential in the transaxle
Page 1344 of 2103

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
solder with a length lb mm
in.) and diameter of 1.6 in.) on the output bearing:
retainer at the shown positions
the outer race.
167
I
‘168
the output bearing retainer and tighten the
to the specified torque.
Output bearing [retainer mounting bolts: 24Nm (18
the bolts and remove the output bearing retainer.
the outer race from the bearing ‘retainer
and remove the solder. If the solder is repeat
steps using with of 3 mm
in.) ,
Measure the thickness of the crushed ‘with a
micrometer and select a spacer with’
thickness that
will provide the standard. value for
S t a n d a r d v a l u e :
. . .
the spacer selected in the previous the
outer race on the output bearing’ retainer.
a O-ring around: the outer inside diameter
of the outer bearing retainer.
the O-ring with automatic and
tighten the output bearing retainer mounting bolts to the ,
specified torque.
Output bearing
24 Nm (18
the output flange into the case and snap
ring around the bearing.
.
TSB Revision