Page 1329 of 2103
-Transaxle
COMPONENTS
Lubricate all internal
parts with automatic
Itransmission fluid
during reassembly.
22200100127
1.Torque converter
assembly
Thrust washer 5.Front clutch assembly6.Thrust race
7.Thrust bearing 8.Thrust washer
9. Rear clutch assembly
10. Thrust bearing
11.Rear clutch hub
12. Thrust bearing
13. Thrust race 14. band15. drum
16.Snap ring
17. Center support
s p r i n g ,
1 9 . R e t u r n
20.Pressure plate
21.Brake
22.Brake23.Reaction plate:,.
24. Reverse sun gear25. Thrust bearing 26.Thrust race 27. sun 28. carrier. 29.Thrust bearing,30.Output flange..
TSBRevision
Page 1330 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
3218
38 78
Nm
9 Nm 7
41
24 Nm
46
11 Nm8I
- -
42 during reassembly.
44. Oil temperature 45. Oil filter”
46: Valve body assembly
47. Manual control lever
48.
position switch (PNPswitch) End clutch’ shaft 50. Bearing retainer
51. Thrust bearing 52. End clutch 53. Thrust washer
54. End clutch assembly:
55. O-ring
31.Oil dipstick
32. Oil filler tube
33.Snap ring34. servo switch35.Snap ring
36. servo piston37.Spring
38.Anchor rod
39.Detent plate40. Manual control shaft 41. Parking roller support
42.Oil pan43.Gasket
TSB Revision
Page 1331 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL -Transaxle
56. End clutch cover57.Pulse58.Lock bolt59.Idler shaft60.Idler gear61.Spacer62.Gasket63. Idler gear cover
64. Differential bearing retainer
65.Spacer66. Differential front bearing cap
67.Differential assembly
6 8 . G a s k e t69. Differential cover70. Output retainer
71. Center differential assembly
72. Center bearing retainer’
73. Stopper ring
74. unit75. Center bearing retainer7 6 . F r o n t
77. Rear output shaft 78. Transaxle case
DISASSEMBLY
(1) Clean away any sand, mud,. etc. adhered the
transaxle.
(2) Place the transaxle assembly on the workbench w ith the
oil pan down.
(3) Remove the torque converter.
(4) Use the special tool to mount the dial gauge on trans-
axle case and the” play the .-
,
.
(5) Remove the pulse generator “A” and “B”.
(6) Remove the manual control lever, then remove th e
neutral position switch (PNP
(7)Remove the oil pan, magnets and gasket.
Page 1332 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
(8) Remove the oil filter from the
(9) Remove the 10 valve body mounting bolts.
the oil temperature sensor holder and remove
the oil temperature sensor harness from the clamp.
the finger of the solenoid valve grommet,
push the grommet into the case and ‘remove the valv e
body assembly.
out the oil temperature sensor.
the parking roller support.
the set screw of the control shaft and
remove the manual control shaft assembly.
the detent plate.
TSB Revision
Page 1333 of 2103
AUTOMATIC .
OVERHAUL
the cover the cover
the differential the differential
the differential bearing retainer,
.
,
differential,
.
end clutch cover
holder and end
the end clutch
a
Page 1334 of 2103
AUTOMATIC TRANSAXLEOVERHAUL -Transaxle
the thrust
the end ditch hub.
thrust bearing ..
NOTE
It may be stuck to
out the end
the idler gear mounting bolts, then
the idler gear cover and gasket.
the bolt stopper and the bolt.
TSB Revision
Page 1335 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
the tool, pull the idler
remove the idler gear and inner
t h e s p a c e r .
the oil pump installation
the special tool remove the oil
thrust washer
TSB Revision
Page 1336 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
Thrust bearina
the input shaft and remove the front clutch assemb ly
and rear clutch assembly together.
thrust bearing
the clutch hub.
NOTE
The thrust race may be stuck to clutch hub.
thrust bearing
the drum.
TSB Revision