Page 1729 of 2103
ABS-ECU
and Post-installation Operation
Cowl Side Trim (R.H.) and Front Scuff Plate
Removal steps
1. Control unit cover
2. ABS-ECU
INSPECTION
ABS-ECU CHECK
Refer to
Page 1730 of 2103
Page 1731 of 2103

CONTENTS
ABS-ECU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 SERVICE SPECIFICATIONS . . . . . . . . . . . . . . . . . 3
GENERAL INFORMATION2SPECIAL TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . . .3. . . . . . . . . . . . . . . . . .
G-SENSOR2 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ON-VEHICLE SERVICE . . . . . . . . . . . .
. . . . 21WHEEL SPEED . . . . . . . . . . . . . . . . . .
ABS Operation Check . . . . . . . . . . . . . . . . . . . . . . . 21
Refer to for the following items.
BRAKE PEDAL
FRONT DISC BRAKE
LUBRICANTS
REAR DISC BRAKE
REAR DRUM BRAKE SHOE
REAR DRUM BRAKE WHEEL CYLINDER
ON-VEHICLE SERVICE
Brake Booster Operating Test
Brake Drum Inside Diameter Check
with Rear Drum Brakes>
Brake Fluid Level Sensor Check
Brake Lining and Brake Drum
Contact Check
Brake Lining Thickness Check Brake Pedal Check and Adjustment
Check Valve Operation Check
Front Brake Disc Run-out Check
Brake
Front Check and
Front Check
Proportioning Valve Test
Rear Brake Check
Rear Brake Disc Run-out Correction
Rear Brake Disc Thickness Check
Rear Disc Brake Pad Check and Replacement
Stop Light Switch Check
Refer to GROUP for the following items.
H Y D R A U L I C U N I T
MASTER CYLINDER AND BRAKE BOOSTER
PROPORTIONING VALVE
ON-VEHICLE
,
Bleeding,
Page 1732 of 2103
ABS General Information
G E N E R A L I N F O R M A T I O N
The ABS consists of wheel speed sensors, stop light switch, hydraulic unit and the ABS-ECU. If be erased even if the ignition switch is turned to
OFF.
a problem occurs in the system, the malfunctioning
system can be identified by
meansof the diagnostic
In addition, reading of diagnostic trouble codes
function, and the trouble symptom memory will’ not and service data
actuator testing are possible
using
the scan tool.
S p e c i f i c a t i o n s
Wheel speed sensorMagnet coil type
Front ABS rotor
Rear ABS rotor teeth
D I A G R A M
1. ABS-ECU2. Hydraulic unit ABS valve relay
4. ABS motor relay
5. Wheel speed sensor
6. ABS rotor D a t a 9. switch
10. ABS light11. G-sensor
TSB Revision
Page 1733 of 2103
A B S Service Tools
SERVICE SPECIFICATIONS
Standard value
. . .Hydraulic unit solenoid valve internal resistance
Clearance between the wheel speed sensor (1.11-1.12)
mounting surface and the ABS rotor mm (in.)
G-sensor output voltage In laden, stationary 2.4-2.8
With FRONT mark downward3.3-3.7
Wheel speed sensor insulation resistance or more
SPECIAL TOOLS
Scan tool (MUT-II)
l system inspection
ABS check harness
Test harness set
Diagnostic trouble code
check harness
Revision
Page 1734 of 2103

ABS
TROUBLESHOOTING
Check diagnostic trouble codeC h e c k d i a g n o s t i c t r o u b l e c o d e to to
No diagnostic troubleDiagnostic trouble codecode or can’t Diagnostic trouble
displayed c o d e
nicate with scan tool Recheck diagnostic trouble code(s)
then erase (Refer to
No diagnostic trouble
code
.
DIAGNOSTIC TROUBLESHOOTING
Gather information from customer
Is the basic brake system functioning
normallv?
(Refer to
Diagnostic trouble code
Inspection chart for trouble symptoms(Refer to Inspectionchart for diagnostic troubleII
codes (Refer to
cope malfunctions.)
NOTES WITH REGARD TO DIAGNOSIS
The condition listed in the following table are con sidered normal.
ConditionExplanation of condition
System check sound
TSB Revision
ABS operation soundSound of the motor inside the ABS hydraulic unit op erating (whine)2. Sound is generated along with vibration of the (scraping)
3.When ABS operates, sound is generated from the vehi cle chassis due to brake application and release.
(Thump: suspension; squeak: tires)
ABS operationFor road surfaces such as snow-covered roads and gravel roads, the braking distance for
(Long braking distance)vehicles with ABS can sometimes be longer than that for other Accordingly,
advise the customer to drive safely on such roads by lowering the vehicle speed
being overconfident.
. .
Diagnosis detection condition depends on the diagno stic trouble code.
Make sure that checking requirements listed in the “Comment” are satisfied when checking the trouble
symptom again after the diagnostic trouble code has been erased.
Page 1735 of 2103
the scan tool to the connector
check diagnostic trouble codes.
Turn the or .
disconnecting the
tool., __
With a voltmeter
Use the special tool to connect a the
output ‘terminal’ and the terminal the
link connector. Then take a reading of the diagnost ic
‘codes ‘from the movement of the of the
ERASING DIAGNOSTIC TROUBLE
Connect the scan tool to the data link connector then erase the diagnostic trouble codes.
Revision
Page 1736 of 2103
INSPECTION CHART FOR DIAGNOSTIC TROUBLE
.. .
C h e c k a c c o r d i n g t o t h e f o r t h e d i a g n o s t i c t r o u b l e
Diagnostic Inspection item
troubleDiagnostic content. p a g e
code No. .
,
11Right front sensorOpen circuit
.,
15Wheel speed sensor system
21 s e n s o r
output signal
Broken
sensor or OFF
22
41
42
Stop light switch system Open circuit or ON malfunction
Left front solenoid valve systemNo response to
Right front solenoid valve systemdrive signal
43
51
52
Rear solenoid valve system
Valve relay system
Motor relay or motor system
The currents flowing
right and left valves different
under the same condition:,
Valve relay OFF failure
Motor relay OFF failure and
motor drive failure
55ABS-ECU ABS-ECU internal failure
(program maze, etc.)
Detection conditions
A: During system check immediately after starting B: While driving
Revision