Page 1313 of 2103

A U T O M A T I C T R A N S A X L E
OV E R HAUL -Transaxle
I
68
(5) Install the output bearing retainer ‘and tighte n the bolts
to the specified torque.
Output bearing, retainer mounting
24 Nm (18 .,
(6) Loosen the bolts and remove the output bearing
(7) Remove the outer race from the bearing retainer
and remove the solder, If the solder IShot crushed, repeat
steps (4) using the solder with diameter 3 mm
in.). Measure the thickness of the solder
with a micrometer and select a
thickness
that will provide
standard for
Standard value:
m m i n . ) .
(8) Install the spacer selected in the and the
outer race on the output bearing retainer.
(9) Install a new around outer inside diameter,
of the outer bearing retainer.
the O-ring with automatic transmission ‘fluid and,
tighten the output
mounting bolts to the
s p e c i f i e d t o r q u e .
Output bearing retainer mounting
24 Nm (18
the output flange into the case and install a
ring around the bearing.
the bearing retainer using new bolts.
retainer mounting 20 Nm (15
,
TSB RevisionI
Page 1314 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
Thrust bearing
race
the heads of the bolts.
a coating of to bearing
attach to the planetary carrier.
the planetary carrier.
the forward sun gear, thrust race thrust
bearing
and reverse. sun gear.
both sun gears assembled in the previous item
into the planetary carrier.
TSB Revision
Page 1315 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL,
the reaction plate, brake disc and brake plate.
TSB Revision
Page 1316 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL
Identification of thrust bearings, thrust races and thrust washers
IdentificationO.D.
I.D.Thicknessmarking Part No.
mm (in.,
70.0 (2.756)
55.71.4l 1
1.8l 2
2.2 (0.87)
2.6
86.0 (2.598)54.7 (2.126)
1.8
48.9 (1.925)37.0 (1.457)
1
1.2
1.4
1.6
1.8
2.0
2.2
2.4
48.1 (1.906)34.4 (1.354)
42.6 (1.677)28.0 (1.102)
54.0 (2.126)38.71.6
52.0 (2.047) 36.4 (1.433) 0
45.0 (1.772)28.0 (1.102)
46.0 (1.811)31 (1.220)0.8
52.0 (2.047)
36.4 (1.433) 0
58.0 (2.283)44.0 (1.732)
TSBRevision
Page 1317 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
-Transaxle
the pressure plate used “in disassembly and
install the return spring.
Caution
Position the return spring correctly when
a coating of jeliy to the wave
and attach it to center support.
the special tool on the center support,’
new O-rings and push into the transaxle case.
Caution
1.Coat the O-rings with
and align the h o l e s .
2.Do not move the of When
installing..
the snap ring.
a feeler gauge and measure the end’ play of the
low-reverse brake. Adjust to the by select-
ing the ‘proper pressure plate.
Standard value:
Page 1318 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL Transaxle
the air exhaust plug, and then install the
Air exhaust plug: 33 Nm (24
the anchor rod.
TSB Revision
the servo spring, piston and sleeve.
Caution
The seal ring alignment hole of
piston must not the oil filler port
by the arrow in the
the special tool to push in the servo
and sleeve, and then install a snap ring.
the band.
Caution
Install so the arrow mark is facing forward.
Page 1319 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL Transaxle .
thrust bearing and washer the
rear clutch.
.
Thrust bearing
race
TSB Revision
the rear clutch assembly front
assembly.
.
thrust bearing the rear clutch- hub.
the rear clutch hub, the ,
thrustrace ontheend of ‘the hub.
Page 1320 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
Thrust washer Thrust race
thrust bearing in the, drum.
. ,
the clutch assembly in the drum.
the clutch assembly and drum into the
transaxle case at the same time.
thrust race and washer to back
of the oil pump with
the special tool to install, a oil pump gasket
and oil pump assembly.
Oil pump assembly mounting bolts: 21 Nm
Revision