Page 1689 of 2103

CONTENTS
ABS-ECU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 VALVE. . . . . . . . . . . . . . . . .
GENERAL INFORMATION. . . . . . . . . . . . . . . . .2SERVICE SPECIFICATIONS.. . . . . . . . . . . . . .3
HYDRAULIC UNIT . . . . . . . . . . . . . . . . . . . . . . . . .36SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . .3
MASTER CYLINDER ANDTROUBLESHOOTING.. . . . . . . . . .. . . . . . . . .4
BRAKE BOOSTER. . . . . . . . . . . . . . . . . . . . . . . . .32..
W H E E L S P E E D .. . . .... . . . . . . . . . . . .38
ON-VEHICLE SERVICE24.... . . . . . . . . . . . . . . . . . . .
ABS Operation Check . . . . . . . . . . . . . . . . . . . . . . .
24
Bleeding
. . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Refer to GROUP for the following items.
BRAKE PEDAL
FRONT DISC BRAKE
LUBRICANTS
REAR DISC BRAKE
REAR DRUM BRAKE SHOE
REAR DRUM BRAKE WHEEL CYLINDER
ON-VEHICLE SERVICE
Brake Booster Operating Test
Brake Drum inside Diameter Check
Brake Fluid Level Sensor Check
Brake Lining and Brake Drum Contact Check
Brake Lining Thickness Check
Brake Pedal Check and Adjustment
Check Valve Operation Check
Front Brake Disc Run-out Check
Front Brake Disc Run-out Correction
Front Brake Disc Thickness Check
Front Disc Brake Pad Check and Replacement
Front Disc Brake Rotor Check
Proportioning Valve Function Test
Rear Brake Disc Run-out
Rear Brake Disc Run-out
Rear Brake Disc Thickness
Rear Disc Brake Pad and Replacement
S t o p L i g h t S w i t c h
Page 1690 of 2103
ABS General Information
The ABS consists of wheel speed sensors, stop light switch, hydraulic unit and the ABS-ECU. If
a problem occurs in the system, the malfunctioning
system can be identified by means of the diagnostic
function.
The diagnostic trouble code will not be erased even
if the ignition switch is turned to OFF.
In addition, reading of diagnostic trouble codes,
service testing are possible using
t h e s c a n
Items
Wheel speed sensor
Front ABS rotor teeth
Rear ABS rotor teeth
,
Magnet coil type
4 3
43
DIAGRAM
1. ABS-ECU6. ABS rotor7. Data link connector .
6. Stop
9. ABS warning light
2. Hydraulic unit
3. ABS valve relay
4. ABS motor relay
5. Wheel speed sensor
TSB Revision
Page 1691 of 2103
ABSService Specifications/Special ,
SERVICE SPECIFICATIONS2
ItemsStandard value
Hydraulic unit solenoid valve internal resistance
Wheel speed sensor internal resistance I
Clearance between the wheel speed sensor
mounting surface and the ABS rotor mm (in.)2 8 . 2 - 2 8 . 5 ( 1 . 1 1 - 1 . 1 2 )
Wheel speed sensor insulation resistance ioo or more
SPECIAL TOOLS
,
scan tool (MUT-II) is
ABS check harness
TSB Revision
Page 1692 of 2103

ABS
TROUBLESHOOTING
DIAGNOSTIC TROUBLESHOOTING
Gather information from customer
.
Check diagnostic trouble code
(Refer to Check diagnostic trouble (Refer to
No diagnostic
trouble code or
with scan tool
Is the basic brake system functioning
normally?
Recheck trouble symptom.
Check diagnostic trouble codes
(Refer to
No diagnostictrouble
Inspection chart for trouble symptoms(Refer to Inspection chart for diagnostic troublecodes (Refer to
NOTES WITH REGARD TO DIAGNOSIS
The condition listed in the following table are con sidered normal.
ConditionExplanation of condition
No
.
TSB Revision
System check sound When starting the engine, a thudd
ing sound can sometimes be heard coming from inside.the engine compartment, but this is because the system operatioh check is being
performed. This is considered normal.
ABS operation sound
ABS operation (Long braking distance)1.Sound of the motor inside the ABS hydraulic unit. o perating (whine),
2. Sound is generated along with vibration of the b rake’ pedal.
3.When ABS operates, sound is generated from the vehi cle chassis due
brake application and release.
(Thump: suspension; squeak: tires)
For road surfaces such as snow-covered roads and gravel roads, the braking distance forvehicles with ABS can sometimes be longer than that for other vehicles. Accordingly,
advise the customer to drive safely on such roads by lowering the vehicle speed and not
being overconfident.
Diagnosis detection condition depends on the diagno stic trouble code.
Make sure that checking requirements listed in the “Comment” are satisfied when checking the trouble
symptom again after the diagnostic trouble code has been erased.
Page 1693 of 2103
warning light
(1) Use the special tool code check
harness) to ground the terminal (1) of the data lin k
connector.
,
.
(2) a ‘reading the trouble code from the
flashing of the ABS warning
.
Diagnostic trouble code No. 24 is output
0.5 sec. No diagnostic trouble code is output 0.5
s e c .
IlluminatedIlluminated
Switched off
.
PauseTens digit DigitFirst digit
time: division: 3
2
NOTE
Diagnostic trouble code No. 16 can be output when t he
ABS system fails because of a battery surge.
Page 1694 of 2103
ABS
ERASING DIAGNOSTIC TROUBLE CODES
With the Scan . .
Connect the scan tool to the data link connector then erase the
With the Warning Light
When the ignition switch is turned on while the sto p light switch is on,
10 times in succession according to the timing given below.
C a u t i o n
The memory cannot be erased under the following con ditions.
(1) When the stop light switch is not turned on and off according to the
(2) When the generator terminal voltage increased (HI state).
Ignition switch
Generator
terminal voltage
Stop light switch
Warning light
ON
OFF
II
ON
OFF_ _
ABS-ECU memory . . .Eliminated
TSB Revision
Page 1695 of 2103

ABS Troubleshooting
INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODES’
Check according to the inspection chart that is appropriate for diagnostic trouble code.
Diagnostic
Inspection item Diagnostic contentDetection
trouble
code No.
11Right front wheel speed sensor
12Left front wheel speed sensor
13Right rear wheel speed sensor
14Left rear wheel speed sensor
15Wheel speed sensor system
16Power supply system
21Right front wheel speed sensor
22Left front wheel speed sensor
23 Right rear wheel speed sensor
24Left rear wheel speed sensor
38Stop light switch system
Right front solenoid valve system
42Left front solenoid valve system
43 Rear solenoid valve system
51Valve relay system
53Motor relay or motor system Open circuit
A,
Abnormal output signal El.
Abnormal battery posi-A,t i v e v o l t a g e
Excessive gap
or short circuit
Open circuit or ON A,
function
No response to sole-
A, valve drive signal
Valve relay OFF failureA,
Motor relay OFF failure
and motor drive failure
ABS-ECU Malfunction in
ECU (program maze,
etc.)
Detection conditions
A: During system check immediately after starting
When driving
TSB Revision
page
Page 1696 of 2103
ABS Troubleshooting
INSPECTION PROCEDURE CLASSIFIED BY DIAGNOSTIC TROUB LE
Code No. Wheel speed sensor open circuitProbable
[Comment]The ABS-ECU detects breaks in the wheel speed sensor wire.l
Malfunction of wheel l Malfunction of wiring harness or l Malfunction of ABS-ECU
NG Repair(Refer to
OK
Measure at ABS-ECU connector l Disconnect the connector and mea-
sure at the harness side.
l Resistance value between terminals
NG Check the following connectors: NG Repair landI
Wheel speed sensor output voltage check
O K
Wheel bearing end play check Refer to GROUP 26
On-vehicleService.Refer to GROUP 27 On-vehicleService.
Check the following connector:
l
OK1Check trouble symptom.
NG Repair
Replace the ABS-ECU.
TSB Revision