Page 505 of 2103
On-vehicle Inspection of
ENGINE (NON-TURBO)>
TSBRevision
Page 506 of 2103
of
E N G I N E , , ,
Evaporative
TSB Revision
Page 507 of 2103
Page 508 of 2103
28 of
( N O N - T U R B O ) >
Bottom view
of relay
I
Intake air temperature
RELAY RELAY)
RELAY CHE.
1. Remove the relay.
2.Check that there is (4) , and (6)
terminals..
Standard value:
.,
3.Use jumper leads to connect to
battery terminal and terminal
terminal.. . .
Check the continuity between
connecting and disconnecting the lead, at the,
battery
terminal. ,
Connected
DisconnectedContinuity
No continuity
4.If there is a defect, replace the (ASD) relay or fuel
pump relay.
INTAKE AIR TEMPERATURE SENSOR CHECK
1.Disconnect the intake air temperature sensor connec tor.
2. Measure the resistance between the sensor terminals.
Temperature Resistance
I 25 (77) 9 - 1 1I
I
INSTALLATION
1. Apply sealant to threaded portion.
Specified sealant: Loctite 24200 or equivalent
2. Install intake air temperature sensor and tighte n it to
specified torque.
Sensor tightening torque: 7 (5
3. Fasten harness connectors securely.
TSB Revision
Page 509 of 2103
On-vehicle Inspection of
ENGINE
TEMPERATURE SENSOR
CHECK
1. Disconnect the engine coolant temperature sensor
connector.
2. Measure the resistance between the sensor terminals.
INSTALLATION
1. Apply sealant to threaded
Specified sealant: Loctite 24200 or equivalent
2.
engine coolant sensor tighten
it to specified torque.
Sensor tightening torque: 7 (5
3. Fasten harness connectors securely.
THROTTLE POSITION SENSOR CHECK
1. the throttle position sensor connector.
2. Measure the resistance between the throttle posi tion
sensor side connector terminal 1 and terminal 3.
Standard value:
3. Measure the resistance between the throttle
sensor side, connector terminal 2 terminal 3.
Throttle valve slowly open until
fully open from the idle positionChanges smoothly in
t o t h e
angle of the
4. If the resistance is outside the standard value, ‘if it
doesn’t change smoothly, replace the throttle posit ion
sensor.
TSB Revision
Page 510 of 2103

On-vehicle of
ENGINE ( N O N - T U R B O ) >
o x y g e n s e n s o r
1. Disconnect the heated oxygen
2. Check that there is continuity between terminal 3 and
terminal 4 on the heated oxygen sensor connector.
3.If there is no continuity, replace the heated oxyge n sensor.
4.Warm up the engine until engine coolant is
or higher.
5.Use the jumper wires to connect terminal 3 of the h eated
oxygen sensor connector to the battery terminal and
terminal 4 to the battery
terminal.
Caution
Be very careful when connecting the jumper wires,
or the heated oxygen sensor can be damaged.
6. Connect a digital voltmeter between terminal 1
terminal 2.
7.While repeatedly racing the engine, heated
oxygen sensor output voltage.
Standard value:
Engine
TSB Revision
If-you make
ratio rich by racing the
engine repeatedly, a
normal heated oxygen
sensor will output a
voltaae of
8. If the sensor is defective, replace the heated
sensor.
NOTE
For removal and installation of the heated sensor,
refer to GROUP 15 Exhaust Pipe, Main Muffler.
oxygen sensor (rear)>
1. Disconnect the heated oxygen
connector.
2. Check that there is continuity terminal and
terminal 2 on the heated oxygen, sensor
3.If there is no continuity, replace the heated
NOTE
1.If the scan tool does not display the standard valu e
although no
malfunctionis found by t h e
above-mentioned continuity test and harness check,
replace the heated oxygen sensor (rear).
Page 511 of 2103
On-vehicle Inspection of ENGINE (NON-TURBO)> 1
2. removal and installation of the oxygen sensor,
refer to GROUP 15
Exhaust Pipe, Main
TSB Revision
Page 512 of 2103

32On-vehicle, Inspection of
(NON-TURBO)>
INJECTOR CHECK
MeasurementofResistance between Terminals
1. Remove the injector connector.
2. Measure the resistance between terminals.
Standard value:
[at
3. Install the injector connector
Checking operation sound
Using a stethoscope or long blade screwdriver, chec k the
operation sound (“tick-tick-tick”) of injectors dur ing idling or
during cranking
Check that as the engine speed increases, the frequ ency
of the operating sound also increases.
Caution
Note that even if the injector you are checking is not
operating, you will hear the operating sound of the other
injectors.
NOTE
If no operating sound is heard from the injector th at is being
checked, check the injector drive circuit. If there is nothing
wrong with the circuit, a defective injector or PCM is suspected
IDLE AIR CONTROL MOTOR (STEPPER
MOTOR) CHECK
Coil Resistance Check
1. Disconnect the idle air control motor connector.
2.Measure the resistance between terminal 1 and termi nal
4of the connector at the idle air control motor side .
Standard value: 36-52
[at
3.Measure the resistance between terminal 2 and termi nal
3 of the connector at the idle air control motor side.
Standard value: 36-52
[at
TSB Revision