1990 MITSUBISHI SPYDER fuel tank removal

FUEL SUPPLY Tank
FUEL TANK
REMOVAL AND INSTALLATION
Engine (Non-turbo)>34
2.5 Nm
251.8
2.5 Nm
Removal steps
1. Fuel tank
2. High-pressure fuel hose
3. Return hose
4. Fuel pump assembly
5. Fuel gauge unit
6. Fuel cut-off valve assembly
7. Vapor hose
8. Fuel tank filler tube cap9. Filler hose10. Vapor hose
TSB Revision
11. Fuel tank filler tube protector12. Reinforcement13. Fuel tank filler tube assembly14. Packing
NOTE
When replacing the fuel pump assembly or the fuel g auge
unit only, it is possible to work from the service halesunderneath the rear seat cushion without having toremove the fuel tank. (Refer to

SUPPLY ‘Fuel Tank
Enaine
(Refer to GROUP On-vehicle Service.)
2.5 Nm1.8
Removal steps
1. Fuel tank
2. Vapor hose
3. High-pressure fuel hose
4. Return hose
, ,
12. Fuel tank filler protector
14. Fuel tank’ assembly Packing
5. Fuel pump 6. Fuel gauge unit
7. Fuel cut-off valve assembly
6. Vapor hose
.
NOTE
When replacing the fuel or the gaugeunit only, it is possible to work from the holesunderneath the rear seat without having to
TSB Revision

Engine>FUEL SUPPLY
Fuel
(Refer to GROUP On-vehicle Service.)
2.5Nm1.8
25 Nm
Removal steps
1.Fuel tank2. Vapor hose
3. High-pressure fuel hose
4. Return hose
5. Fuel tank differential pressuresensor6. Fuel pump assembly
7. Fuel gauge unit
8. Fuel cut-off valve assembly 9. Vapor hose
lo. Fuel tank filler cap
11. Filler hose
1
13. Fuel tank filler tube protector14. Reinforcement 15. tank tube assembly16. Packing
When replacing pump fuel gauge
unit only, it is possible to work from the service holes
underneath the rear seat, without having toremove the fuel tank. (Refer
TSB Revision

FUEL SUPPLY Fuel Tank
Pre-removal Operation
Pressure of Fuel (Refer to GROUP On-vehicle Service.) Il . . . . .
and Hose.
Post-installation Operationl Propeller Installation to GROUP 25 Propeller
Fuel Leaks
Propeller Shaft.)
13
Nm
.
13
25
4936
Removal Steps
1. Heated oxygen sensor connection
2. Center exhaust pipe
3.Protector4.Band5.Fuel tank6. High-pressure fuel hose7.Return hose8.Suction hose9. Pipe 10. Cap11. Fuel gauge unit and pumpassembly gauge unit and pipe assembly
14. hose
TSB
Revision
Shaft.)
15. Fuel cut-off valve assembly16. Fuel tank filler tube cap
17. Filler hose
18. Vapor hose19.Fuel tank filler tube protector
20. Reinforcement21. Fuel tank filler tube assembly
22. Packing
NOTEWhen replacing the fuel gauge unit and pumpor the fuel gauge unit and pipe assembly only, it is to work from the service holes rear seatcushion without having to remove the fuel tank. (Refer to

EVAPORATIVE EMISSION CANISTER/FUEL TANK PRESSURE
RELIEF VALVE/PURGE CONTROL VALVE
REMOVAL AND INSTALLATION
Engine (Turbo)>
Pre-removal and Post-installation OperationBattery Removal and Installation
Removal steps
1. Battery bracket
2. Shift and con-
nection3. Vapor hose4. Connector5. Vapor hose 6. Fuel tank pressure relief 7. Vapor hose 8. Vapor hose
9. Check valve
1 0 . C l a m p ’
hose
12. Purge control
13. Evaporative canister
14. Evaporative emission canister
e r a s s e m b l y
TSB Revision