Page 25 of 2103

GENERAL Towing and Hoisting
Sling type
Wheel lift type
Flat bed type
Dolly type
TOWING WHEN KEYS ARE, NOT, AVAILABLE .
When a locked vehicle must be towed and not
able, the vehicle may be lifted and towed from the front;
provided the parking brake is released. If not rele ased,. the
rear wheels should be placed on a tow dolly.
SAFETY PRECAUTIONS
The following precautions should be towing the
vehicle.
1.DO NOT LIFT OR TOW THE BY ATTACHING
TO OR WRAPPING AROUND BUMPER.
2. Any loose or protruding
of vehicle such
as hoods, doors, fenders,
etc., should be secured
or removed prior to moving
vehicle.
3.Operator should refrain going under a vehicle while
it is lifted by the towing unless the vehicle
is adequately supported by safety stands.
4. Never allow passengers to ride in a towed vehicl e.
5. State and local rules and regulations must be fo llowed
when towing a vehicle.
Caution
1.If only the front wheels or only. the rear wheels a re
lifted for towing, the bumper will be damaged.
In addition, lifting of the rear wheels causes the oil
to flow forward, and may result in heat damage to
the rear bushing of the transfer, and should never
be done.
2.Do not tow the vehicle ‘with “only front or
only the rear wheels on a dolly, or the viscous
coupling will be damaged. In a
case, the vehicle
may jump forward suddenly.
3. If this vehicle is towed, use
bed dolly
type equipment.
TSB Revision
Page 26 of 2103
GENERAL Towing and Hoisting. .
LIFTING, JACKING SUPPORT
FLOOR JACK
nember
Piece wood
1Rear
Caution
Never support any point other than the specified one, or it will be deformed.
TSB Revision
Page 27 of 2103
G E N E R A L T o w i n g a n d
RIGID RACK
For lifting, put rubber or similar between the side sill and rigid rack, or the side sill area
be damaged.
POST TYPE
Special care should be taken when raising the vehicle on a frame contact type The
be equipped with the proper adapters in order to support the vehicle at the
Caution
When service procedures require removing rear suspe nsion, fuel tank and spare tire, place
weight on rear end of vehicle or anchor vehicle to hoist to prevent tipping of center of
changes.
TSB Revision
Page 28 of 2103

G E N E R A L Special Handling AWD M o d e l s
0 0 0 0 3 6 8 5
0 0 1 0 0 7 4 0 0 1 0
Speedometer tests, brake tests and wheel balance me asure-
ment for full-time AWD vehicles should be carried o ut accord-
ing to the following procedures.
SPEEDOMETER TEST
Refer to GROUP 54 Combination Meter.
BRAKE TEST
In order to stabilize the viscous coupling‘s draggi ng force,
the brake test should always be conducted after the speedom-
eter test.
FRONT WHEEL MEASUREMENTS
Place the front wheels on’ the brake tester.
2. Perform the brake test.
Caution
The rear wheels should remain on the ground.
3.If the brake dragging force exceeds the specified
jack up the vehicle and each -to
check the rotation condition of each wheel.
NOTE
If the brake dragging force exceeds the specified
the cause may be the effect of the viscous
dragging force, so jack up the front and check
the rotation condition of the wheels in this state for no
effect by the viscous coupling‘s dragging force.
REAR WHEEL MEASUREMENTS
After placing the rear wheels on the brake tester, follow the
same procedures as for the front wheel measurements .
Brake force of AWD models with
If both front wheels are locked and rear wheel meas urement
is difficult, the measurement in this condition can be consid-
ered to comprise the total.
ItemsBrake force
Total for left andAt 90 kg (198 ped- 20 or more of rear
right rear wheels al depression forceaxle weight
8% or less of rear 8% or less of
r e a r
and right front axle weight
axle weight
wheels/differ-
ence for left and
right rear wheels
T o t a l f o r f r o n t or more of the
and rear wheels al depression forcevehicle’s weight
or...
Braking-stop distanceAt primary velocity of (31mph): Within 15.0 (49.2 ft.)
TSB Revision
Page 29 of 2103

GENERAL Special Handling Instructions for Models
W H E E L B A L A N C E,
FRONT WHEEL MEASUREMENTS
1. Jack up the rear wheels, and place an axle at
the designated part of the side sill.
2. Jack up the front wheels and set, a pick-up stan d and
balancing machine in place.
Caution
1.Set so that the front and rear of the vehicle are
at the same height.
2. Release the parking brake.
3.Rotate each wheel manually and check to be sure
that there is no dragging.
3. Use the engine to drive the tyres, and then make the
measurement.
Caution
1.If an error is indicated in the state of engine drive,
motor drive can be used concurrently.
2. Do not operate the clutch suddenly, or increase or reduce speed suddenly during the work.
REAR WHEEL MEASUREMENTS
1. Jack up the front wheels, and ‘place an, ‘axle s tand at
the designated part of the side sill.’
2.Jack up the rear wheels, and then, setting a pick-up
stand and balancing machine in place, follow the sa me
procedure asfor front wheel measurements.
TSB Revision
Page 30 of 2103

GENERAL General Data and Specifications“
00199999191
ECLIPSE
74
1l ‘: MD
.
GENERAL SPECIFICATIONS
VehicleOverall length mm (in.) 14,380 (172.4)4,380 (172.4)4,3804,380 (172.4)
Overall width mm 21,735 (68.3) 1,735
sions(in.) (68.3)
1,735 (68.3)1,735 (68.3)
Overall height (unladen) 31,295 (51 1,295 (51 1,295 (51 1,295(51
mm (in.)
W h e e l b a s e m m ( i n . ) 42,510 (98.8)
2,510 (98.8)2,510 (98.8)2,510 (98.8)
Tread Front mm (in.) 51,515 (59.6)
1,515 (59.6) 1,515 (59.6)1,515 (59.6)
Tread Rear mm (in.) 61,510 (59.4)
1,510 (59.4) 1,510 (59.4)1,510 (59.4)
Overhang Front 7935 (36.8)
935 (36.8) 935 (36.8)935 (36.8)
mm (in.)
Overhang Rear 8935 (36.8) 935 (36.8) 935 (36.8)935 (36.8)
mm (in.)
Minimum running ground 9145 (5.7) 145 (5.7) 145 (5.7)145 (5.7)
clearance mm (in.)
A n g l e o f a p p r o a c h 1 011.8 11.8 11.811.8
degrees
A n g l e o f d e p a r t u r e 1 115.8
15.8 15.815.8
degrees
Curb weight1,236 (2,725)1,266 (2,791) 1,245 (2,745)1,275 (2,811)
Gross vehicle
weight rating1,660(3,660)1,660 (3,660) 1,690 (3,726)1,690 (3,726)
Gross axle weight rating1 ,010 (2,227)1 ,010(2,227)1,010 (2,227)1,010 (2,227)
Front
Gross axle weight rating
800 (1,764) 800 (1,764) 800 (1,764)800 (1,764)
Rear
capacity4 4 44
Model No. (DOHC) (DOHC) (DOHC) (DOHC)
Piston displacement
1,996 (121.8)1,996 (121.8) 1,996 (121.8)1,996 (121.8)
Model No.
m a n u a l m a n u a l
automatic automatic
Fuel supply system
Electronically
Electronically ElectronicallyElectronically
controlled multi- controlled multi- controlled multi-controlled multi-
port fuel port fuel port fuel port fuel injec-
tion
tion tiontion
TSB RevisionI
Page 31 of 2103

GENERAL General Data and Specifications
Items
,Vehicle Overall length mm (in.) 1 (172.4) 4,380 (172.4) 4,380 (172.4) 4,380 (172.4)
sionsOverall width mm (in.)2 1,735 (68.3)
1,740
1,735 (68.3)
1,740
1,740 (68.5) 1,740 (68.5)
(unladen) 31,295 (51 1,295 (51 1,295 (51 1,295 (51
W h e e l b a s e m m ( i n . ) 42,510 (98.8) 2,510 (98.8)2,510 (98.8)
Tread Front mm (in.) 51,515 (59.6)1,515 (59.6)1,515 (59.6) 1,515 (59.6)
Tread Rear mm (in.) 61,510 (59.4) 1,510 (59.4) (59.4)1,510 (59.4)
Overhang Front 7935 (36.8) 935 (36.8)935 (3.6.8) 935 (36.8)
mm (in.)
Overhang Rear 8935 (36.8) 935 (36.8)935 (36.8) 935 (36.8)
mm (in.)
Minimum running ground 9145 (5.7) 145 (5.7)145 (5.7) 145 (5.7)
clearance mm (in.)
A n g l e o f a p p r o a c h 1 011.811.811.8
degrees
A n g l e o f d e p a r t u r e 1 115.8 15.81 5 . 8degrees
Curb weight1,285 (2,833) 1,315 (2,899) ,322 1,357 (2,992)
Gross vehicle weight rating 1,750 (3,858)1,750 (3,858) 1,750 (3,858)(3,858)
Gross axle weight rating 1 ,010 (2,227) 1 ,010 (2,227) 1,025 (2,260)
Front
Gross axle weight rating 800 (1,764)800(1,764)775(1,709)775 (1,709)
Rear
Seating capacity
Model No.
Piston displacement
Model No.
Fuel supply system
ystem
4 444
(DOHC) (DOHC) (DOHC)
1,996 (121.8)1,996 (121.8) 1,997 (121.9)1,997
m a n u a l manual
automatic automatic
Electronically Electronically Electronically Electronically
controlled multi- controlled multi-
controlled multi-controlled multi-
port fuel injec- port fuel injec-port fuel injec-
port fuel injec-
tion tion tion tion
NOTE
l 1: Vehicles with side air dam.
TSB Revision
Page 32 of 2103
GENERAL General and
Vehicle dimensions
weight kg
Overall length mm (in.)
Overall width mm (in.)
Overall height (unladen) mm (in.)
Wheelbase mm (in.)
Tread
Front mm (in.)
Tread
Rear mm (in.)
Overhang
Front mm (in.)
Overhang
Rear mm (in.)
Minimum running ground
mm (in.)
Angle of approach degrees
Angle of departure degrees
Curb weight
Gross vehicle weight rating
Gross axle weight rating
Front
Gross axle weight rating
Rear
1
2
3
4 5
6
7
8
9
10
11
Seating capacity
EngineModel No.
Piston displacement
4
1,740 (68.5)
1,310 (51.6)
(98.8)
1,515 (59.6)
1,510 (59.4)
(36.8)
(36.8)
145 (5.7)
4,380 (172.4)
1,740 (68.5)
1,310 (51.6)
2,510
1,515 (59.6)
1,510
9 3 5
935 (36.8)
145 (5.7)
12.2
16.2
,427 (3,146)
,850 (4,079)
,050 (2,315)
50 (1,874)
4
4
1
5
El
1 . 2 . 2
16.2
1,462 (3,223)
1,850
1,050 (2,315)
(1,874)
4
(DOHC)
997 (121.9)
-speed manual
(DOHC)
1997
automatic
controlled controlled
fuel fuel injection
Revision