Page 1281 of 2103
AUTOMATIC TRANSAXLE Body
48. Pin49. Stopper50. End clutch plug
51. End clutch spring
52. End clutch valve
53. End cover
54. Torque converter clutch control sleeve
55. Torque converter clutch control valve
56. Torque spring
57. N-R control valve58. N-R control 59.60. spnng61. valve62.Lower valve body
TSB Revision
Page 1282 of 2103
AUTO T R A N S A X L E
OVER
2 1 7 5 0 3 3 3
REASSEMBLY SERVICE POINTS
STOPPER PLATE N-D PLATE TEFLON BALL
STEEL BALL LOCATION
VALVE BODY SUB ASSEMBLY
INSTALLATION
Mount the special tools, and secure the upper separating
plate and intermediate plate with the eight mountin g bolts.
Then, demount the special tools.
I
STEEL BALL RELIEF SPRING
VALVE BODY SUB ASSEMBLY
INSTALLATION
(1) Mount the special tools on the intermediate plate.
Install the separating plate.
TSB Revision
Page 1283 of 2103
solenoid
AUTOMATIC TRANSAXLE
OVERHAUL Valve Body.
(3)Secure the lower valvebody with the bolts. Then,
the special tools.
SOLENOID VALVE ASSEMBLY INSTALLATION
Install each solenoid valve in the position shown in the figure.
Solenoid valveWiringcolor
Shift control solenoid valve “A”
Orange
(SCSV-A)
Shift control solenoid valve Yellow
(SCSV-B)
Torque converter clutch
(TCC solenoid)
Pressure control solenoid Red/Black
valve (PCSV)
TSB Revision
Page 1284 of 2103
Page 1285 of 2103

.
GEAR AND TRANSFER DRIVE
GEAR SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CENTER DIFFERENTIAL . . . . . . .103
DIFFERENTIAL. . . . . . . . . . . . . . . . . . . . . . . . . . . .90
END CLUTCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
EXTENSION HOUSING . . . . . . . . .118
FRONT CLUTCH. . . . . . . . . . . . . . . . . . . . . . . . . .78
FRONT OUTPUT SHAFT . . . . . .
GENERAL INFORMATION. . . . . . . . . . . . . . . . . .2
SERVO . . . . . . . . . . . . . . . . . . . . . . .93
LOW-REVERSE BRAKE. . . . . . . . . . . . . . . . . .
OIL PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
PLANETARY GEAR
. . . . . . . . . . . . . . . . . . . . . . .85
REAR CLUTCH. . . . . . . . . . . . . . . . . . . . . . . . . . .80
SPECIAL TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . .13
6. . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Ratio Table . . . . . . . . . . . . . . . . .6
Pressure Plates, Snap Rings and
Spacers for Adjustment . . . . . . . . . . . . . . . . . . . . . . .8
Sealants and Adhesives. . . . . . . . . . . . . . . . . . . . .12
Service Specifications. . . . . . . . . . . . . . . . . . . . . . . .7
Torque Specifications
Transaxle Model Table. . . . . . . . . . . . . . . . . . . . . . .6
Valve Body Spring Identification Chart
. . . . . . . . .7
SPEEDOMETER GEAR. . . . . . . . . . . . . . . . . . . .95
TRANSAXLE. . . . . . . . . . . . . . . . . . . .17
TRANSAXLE. . . . . . . . . . . . . . . . . . .
TRANSFER. . . . . . . . . . . . . . . . . . .
TRANSFER CASE . . . . . . . . . . . . . .115
TRANSFER CASE ADAPTER . .
TRANSFER SHAFT . . . . . . . . . . . . .
VALVE BODY. . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Page 1286 of 2103

AUTOMATIC TRANSAXLE
OVERHAUL
General
Precautions to be taken when disassembling and the
Because the automatic transaxle is of component parts of especially high degree of
precision, these parts should be very carefully han dled during disassembly and assembly so as not
to scar or scratch them.
A rubber mat should be placed on the and it should always be kept clean.
During disassembly, cloth gloves or shop towels, sh ould not be used.
such items must be used,
either use articles made of nylon, or use paper tow els.
All disassembled parts must be thoroughly cleaned.
Metal parts may be cleaned with ordinary but must thoroughly air dried.
Clean the clutch disc, resin thrust plate and rubbe r parts by using ATF (automatic transmission fluid) ,
being very careful that dust, dirt, etc. do not adhere to them.
Do not reuse gaskets, oil seals, or, rubber parts.
Replace such parts with new ones at every reassembl y. The oil’ gauge need not
be replaced.
Do not use grease other than petrolatum jelly.
Apply ATF to friction components, rotating
and sliding parts before installation.
A new clutch disc should be immersed in ATF for at least two hours before installation.
Do not apply sealer or adhesive to gaskets.
When a bushing must be replaced, replace the assemb ly in which it is incorporated:,
If the transaxle main unit is damaged, also disasse
mble and clean the ‘cooler system.,
TSB Revision
Page 1287 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL General
SECTIONAL VIEW
Kick-Torque converter
clutchOil pumpdo\bra
TorqueFront
clutch Rear
clutchgear
Transferdrive gear
End
TSB Revision
D i f f e r e n t i a l
Page 1288 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL
General Information
SECTIONAL VIEW
Torque converter Oil pump
Front R e a r
clutch brakeclutch
Torque
Transfer
Planetary
gearTransferidler gear
reverse
brake
Endclutch
TSB Revision
c o u p l i n g
Front
differential
snaft.