Page 1593 of 2103
POWER PLANT MOUNT Specifications/Special Tools/Troubleshooting
SERVICE SPECIFICATIONS
Installation dimension of front roll stopper bracket assembly mm (in.)
Bushing (A) projection mm (in.)
Crossmember Bushing (B) projection mm (in.)
Bushing
projection mm (in.)
TOOL
Symptom Probable cause
Excessive engine Cracked rubber parts of insulator Remedy
Replace
wobble or vibration
(with engine in normal
condition) Insufficiently tightened parts Retighten
Abnormal noise
Insufficiently tightened parts Retighten
TSB Revision
Page 1594 of 2103
32-4P O W E R P L A N T M O U N T
REMOVAL AND INSTALLATION
OperationJack Up the Engine and Transaxle Assembly Until Thereis no Weight on the Engine Mount Bracket Insulator.
Engine (Non-turbo)>
86
63
9871
Removal steps
1. Enaine mount insulator mounting
2. Engine mount bracket 3. Engine mount stopper
Engine sideEngine
mount Engine
mount
stopper
______ .bracket
Engine (Turbo) and Engine>
87 .
,
9871 85
INSTALLATION POINT
ENGINE MOUNT
Align the notches on the stopper with the engine bracket
with the arrow mark facing toward the shown
install the stopper.
,
INSPECTION
lCheck each insulator for cracks or damage.
lCheck each bracket for deformations or damage.
TSB Revision
Page 1595 of 2103
POWER PLANT MOUNT Transaxle
TRANSAXLE MOUNTING
REMOVAL AND INSTALLATION
and Post-installation OperationlAir Cleaner Assembly Removal and Installationl Battery Removal and Installationl Engine Roll Stopper, Centermember AssemblyRemoval and Installation (Refer to
Engine (Non-turbo)> Engine (Turbo) and Engine>
69 Nm3.
NOTEl
1. Battery bracket
2. Evaporative emission canister
Engine (Turbo)> (Refer to
GROUP 17 Evaporative Emission
Control System)
3. Evaporative emission canister hold- er assembly
Engine (Turbo)>
(Refer to GROUP 17 Evapora-
tive Emission Control System) 4. Battery stay
5.
mount insulator mounting
6. Transaxle mount bracket
7. Transaxle mount stopper
REMOVAL SERVICE POINT
TRANSAXLE MOUNT BRACKET REMOVAL
Slightly lower the transaxle, and then remove the t ransaxle
mount bracket.
TSBRevision
Page 1596 of 2103
32-6
Transaxlemount stopper
POWER PLANT MOUNT Transaxle . ,
Transaxle side l TRANSAXLE MOUNT
Align the notches on the stopper with the transaxle mount
bracket with the arrow mark facing toward the
Then install the stopper. ,
INSPECTION
lCheck each insulator for cracks or damage.
lCheck each bracket for
.
TSB Revision
Page 1597 of 2103
POWEREngine Roll
,
ENGINE ROLL STOPPER, CENTERMEMBER
REMOVAL AND INSTALLATION
44 Nm
Engine (Non-turbo)>
32
88 Nm64
1. Rear roll stopper bracket assembly
2. Front roll stopper bracket assembly
Centermember removal steps
3. Bolts
4. Stay Engine (Turbo) and Engine 5. Centermember assembly
Indicates parts should be temporarily and then fully tightened with the vehicle on the groundin the unladen
TSBRevisionI
Page 1598 of 2103
32-8POWER PLANT MOUNT Engine Roll. Stopper,
(1) Set the special tool to the to the engine
assembly.
(2) Remove the centermember assembly.
INSTALLATION POINT
FRONT
If the dimension shown in the illustration the standard
value when the weight of the engine is the body, replace
the front roll stopper bracket
Standard value (A):
I.
INSPECTION
l each insulator for cracks damage.
l Check each bracket for
damage.
,
.
,
,
Revision
Page 1599 of 2103

POWER PLANT MOUNT Crossmember
CROSSMEMBER
REMOVAL AND INSTALLATION
and Post Installation Operation(1) Power Steering Fluid Draining and Supplying(Refer to GROUP On-vehicle Service.)
(2) Centermember Removal and Instrallation
(Refer to (3) Stay Removal and Installation (Refer to Compression lower and lateral lower armassemblies.)(4)Front Exhaust Pipe Removal and Installation (Referto GROUP 15 Exhaust Pipe and Muffler.)
(5) Stabilizer Bar Removal and Installation (Refer to GROUP
Stabilizer Bar.)(6)Steering Gear Box Removal and Installation (Referto GROUP Power Steering Gear Box.)
Engine (Non-turbo)>
44Nm32
Engine (Turbo) and Engine>
44Nm3 2
88Nm84
88
00003506
Crossmember removal steps
1. Lateral lower arm mounting bolt
2. Compression lower arm
mounting bolts3. Shock absorber lowermounting bolt4. Rear roll stopper bracketmounting bolts5. Bushing retaining self-locking nut
6. Lower plate
7. Bushing retaining self-locking nut
8. Lower plate
Bushing retaining bolt10. Crossmember11. Stopper 12. Stopper A
13. Bushing
14. Bushing A
15. Bushing
Cautionl Indicates parts which should be temporarily tighten ed,
and then fully tightened with the vehicle on the gr ound
in the unladen condition.
TSB Revision
Page 1600 of 2103
POWER PLANT MOUNT
RemovalPress-fitting
Nut
Bushing A
Inner pipe
Bushing
Inner pipe
RemovalPress-fitting
TSB Revision
Inner pipe
CROSSMEMBER BUSHING
B U S H I N G
(1) Apply soapy water to the contact ‘surface of th
e
when press-fitting the bush. ,
(2) The bush should be press-fitted that’ the inner
projection is at the standard length.
S t a n d a r d
Bushing A: mm in.)
Bushing B:
mm in.)
(1) Use the special tool to drive out and press-fit the
member bushing C. .
.
(2) The bushing should be press-fitted so that the inner pipe
projection is at the standard length.
Standard value (A):
mm in.)
INSPECTION
lCheck the crossmember for cracks or deformation.
lCheck the bushings for cracks or’deterioration.