Page 1225 of 2103
end , ,., ,
.
14
the housing and
the six
arrows. ,
the special the bolt ,
the oil’
remove the gasket.
,
, .
the the
case.
. . . . .
.
.
Page 1226 of 2103
AUTOMATIC
OVERHAUL T r a n s a x l e
fiber thrust washer
.
. .
. .
input shaft to, remove the
and clutch assemblies
. .,
,,
. , ,
,
,
(25) Removethrust
the clutch hub. . . .
.
,
race and t h r u s t ,
.
. .
, ,
,--
Page 1227 of 2103
A U T O M A T I C
OVERHAUL Transaxle , .
the d r u m .
(29) Remove
the special tools;’ push in the and
remove the snap ring.
,
,
,
.
the special tools remove the
servo piston, sleeve and
the anchor rod.
TSB Revision
Page 1228 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL Transaxle
Reverse gear
the snap ring.
the special tool on the center support and remove
the center support from the case.
reverse sun gear, thrust bearing thrust race
and forward sun gear together.”
the gear set and thrust bearing
the wave spring, return spring, reaction plate,
brake discs, and brake plates.
TSB Revision
Page 1229 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL ,
has been applied to the threads of
on the bearing retainer. Tap the heads so
can be easily loosened.
,
an impact driver, loosen the and remove
the bearing retained
.
,
,
the idler shaft lock plate.
. the transfer idler shaft with the
. .
. .
transfer idler
gear and the two bearing inner races inside the;
case..
TSB Revision
Page 1230 of 2103
TRANSAXLE
AUL Transaxle
the spacer.
the snap ring from the flange bearing.
the output flange from the
t h e t r a n s f e r s h a f t c o v e r .
the locking tab the transfer lock nut,
where it is bent.
TSB RevisionI
Page 1231 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL
I
the transfer shaft ‘on the end of the converter
housing.
I .
the lock nut.
Caution
The lock nut is a left-handed screw.
out the transfer shaft toward the converter housing
end and remove the transfer shaft and transfer driv en
gear.
the outer races from the transfer shaft bearing.
the set screw, sprag rod and remove the manual
control shaft assembly, detent plate.
TSB Revision
Page 1232 of 2103
A U T O M A T I C T R A N S A X L E
OVERHAUL
Oil pump side
Pressure spring
REASSEMBLY
(1) Before reassembling the transaxle, measure the end play
in the low-reverse brake and select to
obtain the specified end play. Use procedure.
(a)Install the brake reaction plate,
disc in the transaxle. case.
Caution ,
Blow off automatic transmission fluid from the
plates and discs with low-pressure compressed
air.
(b) Install the appropriate pressure and the
return spring.
Make return spring in
the correct
(c) Apply petrolatum jelly to the.. spring and attach
the wave spring on the center support.
the two O-rings removed during disassembly
and coat them with automatic transmission fluid.
i .
Attach the special tool to the center and
the support in the transaxle case.
Caution
1.Install the center support,’ taking care
waved spring is not out of position.
2. Install the two O-rings in alignment
oil holes provided in the
(9 Remove the special tool.
(g)
the snap ring.
TSB Revision