Page 1121 of 2103
AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND Transaxle
REMOVAL AND INSTALLATION
Engine>
Engine(Turbo)>9.8 Nm7.2
.
Engine (Turbo)>
6
9.87.2
Nm
2.9
29199710119
Removal steps
1. Air cleaner cover and air intake
hose
2. Feed hose
3. Return hose
4. Hose assembly Pipe assembly
6. Oil cooler duct
7. Bracket8. Oil cooler assembly
TSB Revision
Page 1122 of 2103
AUTOMATIC TRANSAXLE
ENGINE (TURBO) AND ENGINE> -‘Transaxle Oil Cooler
INSPECTION231
l Check the hose for cracks, damage
lCheck for rusted or clogged transaxle oil cooler.
l Check oil cooler fins for
damage, and clogged
with foreign matter.
TSB Revision
Page 1123 of 2103
AUTOMATIC TRANSAXLE.
ENGINE
GENERAL INFORMATION
The automatic transaxle comes in one model, namely,
22110010012
Items
ModelSpecifications
Applicable engine
Fully-adaptive, electronically controlled
full-automatic
Torque converter
Engine stall speed
with torque
Gear ratio 2 . 8 4 2I
1 . 5 7 3
‘ 1 . 0 0 0
Reverse
Final gear ratio
FUNCTION ELEMENT TABLE
. 0.689 ,
2.214
3 . 9 0 9
Shift Lever Position
PARK
REVERSE
NEUTRAL
StartPark Reverse Low/
Safety
drive
clutch clutchclutchclutch Reverse
clutch
Vehicle upshift and downshift speeds are increased when in these selector positions.
TSB Revision ,
Page 1124 of 2103
AUTOMATIC TRANSAXLE
ENGINE (NON-TURBO)? General
SECTIONAL VIEW
Case
Input speedOverdrive
clutch Reverse clutch
sensor
2-4 clutchUnderdrive
clutch
L o w / R e v e r s eclutch converter
Torqueconverter
.sensor
Oil pump
TSB Revision
shaft
gear
gear
Differential
Page 1125 of 2103
AUTOMATIC TRANSAXLE T o o l s
ItemS t a n d a r d v a l u e .Resistance of input speed sensor ..Resistance of output speed sensor
Resistance of solenoid coil [at Approx. 1
Resistance of solenoid coil [at
Resistance of OD solenoid coil [at A p p r o x . 1
Resistance of UD solenoid coil [at .
Distance between detent pin and detent plate mm (in.)
Installation dimension of front roll stopper bracket assembly mm (in.)
ItemSpecified lubricantQuantity (qts.)
Transaxle fluid DIAMOND ATF SP II or equivalent8.6(9.1)
Scan tool (MUT-II)
Steering linkage puller knuckle removal
lLateral lower arm ball joint
and knuckle removal
lCompression lower arm balljoint and knuckle removal
Revision
Page 1126 of 2103
AUTOMATIC TRANSAXLE
Oil pressure gauge
TSBRevision
Page 1127 of 2103
AUTOMATIC TRANSAXLE
DIAGNOSTIC TROUBLESHOOTING FLOW
.
.Gather information from customer.
Verify complaint
Communication withscan tool not possible
Record the diagnostic trouble code
and fail-gafe code. (Refer to ,
Diagnostic trouble code outputNo diagnostic trouble
Erase the diagnostic trouble code code displayed(Refer to
Basic inspection item adjustment(Refer to
Abnormality exists
(no diagnostic trouble code)
Road test (Refer
Abnormality exists
(diagnostic trouble
code present)
Diagnostic trouble
Recheck trouble codeswhich were recorded before the roadt e s t .
Search for cause.
FoundNot found
NG
OK
‘CompletedConfirmation test (road test)
TSB Revision
Page 1128 of 2103

AUTOMATIC TRANSAXLE ENGINE (NON-TURBO)> Troubleshooting
ROAD TEST
Use scan
ConditionsOperationJudgment value Inspection item Diagnostic
trouble code
1Ignition switch: ON Check the limp-in Data list Transaxle control
Engine: Stoppedmodel No limp-in modemodule
Transaxle control 14
relay15
20
Check the battery Data list Battery12
positive voltage
2Warming up Drive for 15 Data list No. 56 O i l t e m p e r a t u r e 7 4
minutes or more so
that the automatic Gradually rises to
sensor
transmission fluid
temperature
becomes
3Engine:Engine Data list Transaxle control 45
Selector lever(1) (for at least(1) 2.0 module
position:30 seconds) Check diagnos- CCD Bus19
tic trouble code
Solenoid Circuit
Selector lever
position
(3) (4)
(5) 2 (6)
Data list T r a n s a x l e r a n g e 2 8
and neutral position
(3) (4) switches
(5) 2 (6)
3Engine: Idle Accelerator pedal Data list Crankshaft position 18
Selector lever(1) Depressed (for (1) Engine speeds
position:at least 3 displayed on the
scan tool and
tachometer are
identical
Accelerator pedal
Data list T h r o t t l e p o s i t i o n 2 9
(1) Fully closed
400 or moresensor
(2) Fully open (for at least 2 seconds)
(2) 3,800 or less
Revision