Page 1353 of 2103
AUTOMATIC TRANSAXLE
the thrust washer on the return spring
clutch.
the end clutch hub on the
thrust bearing to the end of the hub
with petrolatum.
. .
the end clutch assembly.
a new O-ring the end clutch
.
TSB Revision
Page 1354 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL Transaxle
the end clutch cover and tighten the bolts to the
specified torque.
End clutch cover mounting Nm (8
the differential assembly.
solder with a length of approximately 10
in.) and diameter of 1.6 in.) on the differential
rear bearing retainer at the
the outer race.
the differential rear bearing retainer and tighten
the bolts to the specified torque..
the bolts, remove the differential. bearing
retainer and remove the solder. If the crushed,
repeat steps using the solder with the diameter,
of 3 mm.
Differential rear bearing retainer mounting
35 Nm (26
the thickness of the crushed solder with a mi-
crometer and adjust by selecting a spacer with a th ickness
that will provide the standard value for the. end play and
preload.
Standard
m m
TSB RevisionI
Page 1355 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
Detent plate
a new O-ring on the, differential retainer,
coat the O-ring with then
install in the transaxle case and tighten the mount ing
bolts to the specified torque. ,
Differential rear bearing retainer’ mounting
35
Nm (26
,
the front bearing cap and tighten the the
specified torque.
Differential front bearing cap mounting
70Nm (51
the differential cover and a’ new gasket,
D i f f e r e n t i a l
the detent . .
Detent plate mounting bolt: 11 Nm(8
a new O-ring on the manual control shaft
coat the O-ring automatic transmission fluid and then
insert into the transaxle case.
the groove in the manual control shaft and the set
screw hole; then install the set screw.
Manual control ‘shaft,
the parking roller support.
Parking roller support
bolts:
24 Nm (18
evision
Page 1356 of 2103

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
the oil temperature sensor into the case.
an O-ring in the O-ring groove at the’ top of the
valve body assembly.
the solenoid valve harness grommet
a new one.
the solenoid valve connector through the transaxle
case hole from the inside.
the solenoid valve harness grommet into the case
hole.
the knock pin of the body, into case,
keeping the detent plate pin in the ‘manual valve g roove.
Temporarily install the valve body,
the oil’
ture sensor and holder; then tighten mounting bolts
to the specified torque.
A bolt: 18 mm
in.)
bolt: 25 mm in.)
bolt: 40 mm (1.57 in.)
Valve body assembly mounting bolts: 11 Nm (8
Caution
Firmly fasten the solenoid valve and oil temperatur e!
sensor harness at the shown positions.
Especially, be sure to route the pressure control
valve harness, which is separated from
other harness, as shown in the, diagram and clamp
the harness. Failure to fasten
‘may result in contact
with the detent plate or parking rod.
TSB Revision
Page 1357 of 2103
AUTOMATIC
O V E R H AUL.
oil screen.
Oil filter mounting, 8
,
, , ,
the Oil pan and
pan mounting bolts: Nm
the switch
manual control lever.
Park/neutral position switch, mounting bolts:
Nm (8
Manual control lever 19
the speedometer gear
Speedometer gear
N m ( 4
the servo.
the pulse A and
generator mounting bolts;, .C a u t i o n
Install the black
on the output
t h e t r a n s p a r e n t the ,
the oil filler tube the
O i l f i l l e r t u b e m o u n t i n g
the brackets.
Transaxle mounting bracket bolts: 70 Nm
TSB Revision
Page 1358 of 2103
AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
the servo by following procedure;’
(a) Fit the claw of the special
notch’
piston to prevent the turning, and use
adapter to secure
as at
Caution
1 . D o n o t p u s h i n
2.When the adapter the
case, do not apply
en by hand.
TSB Revision (b) Loosen the lock nut ‘until it
reach the
V-groove in the
the special
tool (inner)
nut.
,
(c) Fit the special tool (outer) to lock nut.‘ Turn the
outer cylinder and the inner
clockwise to lock the lock nut and, the tool
(inner).
. .
. .
,,
(d)Fit a torque wrench to
it to a torque of 10 Nm (7.2 and loosen. ‘Repeat
this sequence twice before tightening the
to 5 Nm torque. ‘Then
t h e s p e c i a l t o o l ( o u t e r ) 2 t o
,
Page 1359 of 2103

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
(e) Fit the special tool (outer) to the
Turn the outer cylinder clockwise and the inner cyl inder
counterclockwise to unlock the
tool (inner).
Caution
When unlocking is carried
apply force
to both special tools to
(f)Tighten the lock nut by hand the piston.
Then, use a torque wrench to tighten the lock nut
to the specified torque.
Lock nut: 29 Nm (21
Caution
The lock nut may turn with the adjusting rod
tightened quickly with a socket wrench or torque
wrench.
(g) Remove the special tool for securing the piston. In stall
the plug to the Low/Reverse pressure outlet and tight-
en to the specified
the switch fasten with a snap
ring.
the center shaft and hit it with a plastic hammer
or similar instrument to install it securely.
NOTE
Apply ATF to the oil seal lip and do not scratch it .
the pump drive hub with transmission
fluid and install the torque converter.
in firmly so
that dimension A in the diagram is at the standard value.
Standard value: approx. 18.3 mm
TSB Revision
Page 1360 of 2103
AUTOMATIC TRANSAXLE
Oil pump
OIL PUMP
DISASSEMBLY AND REASSEMBLY
Lubricate all internal
parts with automatic
transmission fluid
during reassembly.
2 N m
I
8
I
Disassembly steps
1. O-ring 2. Reaction shaft support
3. Steel ball 4. Drive gear 5. Driven gear - 3
6. Seal ring 7. Oil seal8. pump housing
9. Snap ring
10. Oil seal
DISASSEMBLY SERVICE POINT,
GEAR D R I V E N
(1)Place reassembly alignment marks on the and
gears.
R E A S S E M B L Y S E R V I C E P O I N T S
O I L S E A L I N S T A L L A T I O N .
TSB RevisionI