1996 ACURA RL KA9 Service Repair Manual

22. Disconnect the spark plug voltage detection module

connector, and remove the engine ground cables.

6 x 1.0 mm

12 N-m (1.2 kgf-m,

8.7 Ibf-ft)
GROUND

CABLES

SPARK PLUG VOLTAGE

DETECTION MODULE

CONNECTOR

23. Remove the vacuum hoses.

VACUUM

HOSES
24. Loosen the mounting bolt, lock bolt and adjusting

rod, then remove the alternator belt.

ADJUSTING

ROD
LOCK BOLT

8 x
1.25
mm

22 N-m (2.2 kgf-m,

16 Ibf-ft)

ALTERNATOR

BELT
MOUNTING BOLT

10 x
1.25
mm

44 N-m (4.5 kgf-m,

33 Ibf-ft)

25.
Loosen the idler pulley center nut and adjusting

bolt, then remove the air conditioning (A/C) com-

pressor belt.

ADJUSTING

BOLT

IDLER PULLEY

CENTER NUT

10 x
1.25
mm

44 N-m (4.5 kgf-m,

33 Ibf-ft)

A/C COMPRESSOR

BELTProCarManuals.com

Engine Removal/Installatio n
Removal (cont'd )
26. Disconnec t th e powe r steerin g pressur e (PSP ) switc h
connector .
ADJUSTIN GBOLT
LOCKNU T8 x 1.2 5 mm22 N- m (2. 2 kgf-m ,
1 6 Ibf-ft )
PS P SWITC H
CONNECTO R
P/S PUM P
BELTMOUNTIN G BOL T10 x 1.2 5 mm44 N- m (4. 5 kgf-m ,
3 3 Ibf-ft )
27. Remov e th e adjustin g bolt , locknu t an d mountin g
bolt, the n remov e th e powe r steerin g (P/S ) pum p
belt an d pump .
NOTE: D o no t disconnec t th e P/ S hoses .
28 . Pul l th e carpe t bac k underneat h th e fron t passen -
ger' s sea t t o expos e th e secondar y heate d oxyge n
senso r (secondar y HO2S ) connector , the n discon -
nec t th e secondar y HO2 S connector . 29
. Remov e th e radiato r cap .
Us e car e whe n removin g th e radiato r
ca p to avoi d scaldin g b y ho t coolan t o r steam .
30 . Rais e th e hois t t o ful l height .
31 . Remov e th e fron t tires/wheel s an d splas h shield .
SPLAS H
SHIEL D
6 x 1. 0 m m9.8 N- m (1. 0 kgf-m , 7. 2 Ibf-ft )
32. Drai n th e engin e coolan t (se e pag e 10-5 ). Loose n
the drai n plu g in th e radiator .
33. Drai n th e automati c transmissio n flui d (ATF) . Reinstal l
th e drai n plu g usin g a ne w washe r (se e sectio n 14 ).
34 . Drai n th e differentia l oil . Reinstal l th e drai n plu g
usin g a ne w washer (see sectio n 15 ).
35 . Drai n th e engin e oil . Reinstal l th e drai n bol t usin g a
ne w washe r (se e pag e 8-4 ).
36 . Remov e th e dampe r fork s (se e sectio n 18 ).
37 . Disconnec t th e suspensio n lowe r ar m bal l joint s
(se e sectio n 18 ).
38 . Remov e th e driveshaft s (se e sectio n 16 ).
NOTE : Coa t al l precisio n finishe d surface s wit h
clea n engin e oil . Ti e plasti c bag s ove r th e driveshaf t
ends.
SECONDAR Y
HO2 S CONNECTO R
ProCarManuals.com