Page 729 of 2389
COMPONENTS (Cont'd)
CANADA
± BODYSafety PadBO±63
Page 730 of 2389
REMOVAL OF SAFETY PAD
(See pages BO±62, 63)
1. DISCONNECT BATTERY CABLE FROM NEGATIVE
TERMINAL
2. REMOVE STEERING WHEEL
3. REMOVE FRONT PILLAR GARNISH
Pry out the clips and pull the front pillar garnish upward
to remove it by the hand.
4. REMOVE NO. 1 UNDER COVER
5. REMOVE LOWER FINISH PANEL
(a) Remove the two screws and the engine. hood re-
lease lever. HINT: Screw sizes in the previous illustration are indi-
cated by following the code below for removal and
installation of safety pad.
mm (in.)
Shape
ShapeShapeCode
CodeCodeSizeSizeSize
± BODYSafety PadBO±64
Page 731 of 2389
(b) (USA)
Using a screwdrier, pry out the switch bases and the
No. 1 speaker panel.
HINT: Tape the screwdrier tip before use.
7. REMOVE CLUSTER FINISH PANEL
(a) Remove the five screws and the panel.
(b) Disconnect the connectors.(d) (CANADA)
Remove the five screws and lower finish panel.
(e) Disconnect the connectors.(c) (USA)
Remove the seven bolts and lower finish panel.
6. REMOVE STEERING COLUMN COVER
Remove the four screws, the two bolts, and the cover.
± BODYSafety PadBO±65
Page 732 of 2389
8. REMOVE COMBINATION METER
(a) Remove the four screws.
(b) Remove the speedometer cable, connectors and the
meter.
9. REMOVE NO.2 UNDER COVER
10. (USA)
REMOVE GLOVE COMPARTMENT BOX
(a) Remove the screw and pull out the chech arm.
(b) Remove the four screws, the connector, and pull out
the box.
12. REMOVE RIGHT LOWER PANEL
(a) (USA)
Using a screwdrier, pry out the No. 2 speaker panel.
HINT: Tape the screwdriver tip before use. 11. REMOVE GLOVE COMPARTMENT DOOR
Remove the two screws and the door.
± BODYSafety PadBO±66
Page 733 of 2389
13. REMOVE CENTER CLUSTER FINISH PANEL
(a) (USA)
Remove the two screws.
(b) Remove the ash tray.
(c) Using a screwdriver, release the white plastic clip at
the rear of the ash receptacle retainer.
HINT: Tape the screwdrier tip before use.
(d) Pull out the center cluster finish panel.(e) (CANADA)
Remove the five screws.
(d) Remove the panel and disconnect the speaker con-
nector.
14. REMOVE RADIO AND STEREO
(a) Remove the four screws, radio and stereo.
(b) Disconnect the connectors and the antenna cable.(b) (USA)
Remove the five bolts, the three screws and the twc
nuts.
± BODYSafety PadBO±67
Page 734 of 2389
16. REMOVE CENTER LOWER PANEL
(a) (USA)
Remove the two screws and pull out the panel. 15. REMOVE NEATER CONTROL
Remove the four screws and the heater control.
18. REMOVE NUT CONNECTING CENTER BRACKET
AND SAFETY PAD 17. REMOVE SIDE DEFROSTER NOZZLE
HINT: Tape the screwdriver tip before use. (b) (CANADA)
Remove the three screws and panel.
± BODYSafety PadBO±68
Page 735 of 2389
HINT: The safety pad has a boss on the reverse side for
clamping onto the clip on the body side. Therefore, when
removing, pull, upward at an angle.
(e) Remove the clips and disconnect the wire harness
from the safety pad. 19. REMOVE JUNCTION BLOCK NO.3
(a) Remove the speaker.
(b) Remove the two screws and junction block No.3.
20. REMOVE SAFETY PAD
(a) Push on the pawls of speedometer cable, bracket
and pull it from the safety pad.
(b) Remove the four bolts, two screws, two nuts and the
safety pad.
± BODYSafety PadBO±69
Page 736 of 2389
21. REMOVE NO.1 HEATER REGISTER DUCT
Pry out the clip and remove the duct.
22. REMOVE NO.3 HEATER REGISTER DUCT
Remove the three screws and duct.
23. REMOVE DEFROSTER NOZZLE
Remove the five screws and nozzle.
24. REMOVE NO.1 INSTRUMENT PANEL REGISTER
Remove the two screws and register.
25. REMOVE NO.3 INSTRUMENT PANEL REGISTER
Remove the three screws and register.
26. REMOVE NO.2 INSTRUMENT PANEL REGISTER
Remove the screws and register.
27. REMOVE SAFETY PAD GARNISH
INSTALLATION OF SAFETY PAD
(See pages BO±62, 63)
INSTALL SAFETY PAD PARTS FOLLOWING REMOVAL
SEQUENCE IN REVERSE
HINT:
wWhen reinstall the speedometer cable, first pull on
the cable guide casing.
wInsert the flange of def±nozzle between the rib (A)
and the safety pad.
± BODYSafety PadBO±70