Page 2209 of 2389
REAR SUSPENSION (4WD)
HINT: Refer to RA±50 except following points about
4WD.
COMPONENTS
± REAR AXLE AND SUSPENSIONRear Suspension (4WD)RA±62
Page 2210 of 2389

Suspension Arm and Strut Rod
REMOVAL AND INSTALLATION OF
SUSPENSION ARM AND STRUT ROD
Remove and install the parts as shown components on
page RA±62.
(MAIN POINT OF REMOVAL SUSPENSION ARM AND
STRUT ROD)
wPlace matchmarks on the adjusting cam and body.
(No.2 suspension arm only)
(MAIN POINT OF INSTALLATION SUSPENSION ARM
AND STRUT ROD)
wPlace suspension arm or the strut rod in position.
wTemporarily install the bolt to the body and the axle
carrier.
w Bounce the vehicle up and down to stabilize the sus-
pension arm on strut rod.
wAlign the matchmarks on the cam and body
(No. 2 suspension arm only)
wTorque the installation bolt with the vehicle weight on
the suspension.
(See page RA±62)
wCheck rear wheel alignment.
(See page RA±3)
Stabilizer Bar
REMOVAL AND INSTALLATION OF
STABILIZER BAR
Remove and install the stabilizer bar as shown compo-
nents on page RA±44.
INSPECT STABILIZER BAR LINK
Move the ball joint stud in all directions, if the movement
is not smooth and free, replace the stabilizer link.
± REAR AXLE AND SUSPENSIONRear Suspension (4WD)RA±63
Page 2211 of 2389

Suspension Arm and Strut Rod
REMOVAL AND INSTALLATION OF
SUSPENSION ARM AND STRUT ROD
Remove and install the parts as shown components on
page RA±62.
(MAIN POINT OF REMOVAL SUSPENSION ARM AND
STRUT ROD)
wPlace matchmarks on the adjusting cam and body.
(No.2 suspension arm only)
(MAIN POINT OF INSTALLATION SUSPENSION ARM
AND STRUT ROD)
wPlace suspension arm or the strut rod in position.
wTemporarily install the bolt to the body and the axle
carrier.
w Bounce the vehicle up and down to stabilize the sus-
pension arm on strut rod.
wAlign the matchmarks on the cam and body
(No. 2 suspension arm only)
wTorque the installation bolt with the vehicle weight on
the suspension.
(See page RA±62)
wCheck rear wheel alignment.
(See page RA±3)
Stabilizer Bar
REMOVAL AND INSTALLATION OF
STABILIZER BAR
Remove and install the stabilizer bar as shown compo-
nents on page RA±44.
INSPECT STABILIZER BAR LINK
Move the ball joint stud in all directions, if the movement
is not smooth and free, replace the stabilizer link.
± REAR AXLE AND SUSPENSIONRear Suspension (4WD)RA±63
Page 2212 of 2389
SERVICE SPECIFICATIONS
± SERVICE SPECIFICATIONSA±1
Page 2213 of 2389
Front and rear brake
Pad thickness
Disc thickness
Disc runout
Parking brake
Lining thickness
Drum inside diameter
Front axle and suspension
Ball joint vertical play
Steering wheel freeplay
Torque specifications
Front seat mount bolts
Strut/stabilizer bar bracket x Body
Engine mounting center member x Body
Front suspension lower crossmember x Body
Rear suspension lower crossmember x Body
MAINTENANCE
Engine
Engine oil capacity (Drain and refill with oil fitter change)
Gap
Firing order
Valve clearance Coolant capacity 1w/ Heater) Drive belt tension
Alternator
Spark plug
Type
Chassis
PS pump
± SERVICE SPECIFICATIONSMaintenanceA±2
Page 2214 of 2389
ENGINE MECHANICAL (3S±FE)
Specifications
Intake manifold
vacuum
Camshaft and
gearCompression
pressure
Valve guide
bushingCylinder head
Valve spring
Valve lifterIdle speed
ManifoldValve
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±3
Page 2215 of 2389
Specifications (Cont'd)
Idler pulley
tension springCamshaft and
gear (cont'd)
Piston and
piston ring
Connecting rod Cylinder block
Crankshaft
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±4
Page 2216 of 2389
Spark plug tube x Cylinder head
Camshaft bearing cap x Cylinder head
Cylinder head cover x Cylinder head
Intake manifold x Cylinder head
Intake manifold stay x Cylinder head
Intake manifold stay x Cylinder block
EGR valve x Intake manifold
EGR pipe x Cylinder head
Water outlet x Cylinder head
Exhaust manifold x Catalytic converter
Exhaust manifold x Cylinder head
Engine hanger x Cylinder head
Alternator bracket x Cylinder headOil pump pulley x Oil pump drive shaft
No. 1 idler pulley x Cylinder head
No. 2 idler pulley x Cylinder block
Camshaft timing pulley x Camshaft
Crankshaft pulley x Crankshaft
Cylinder head x Cylinder block
Specifications (Cont'd)
Torque Specifications
Crankshaft
(cont'd)
Part tightened
± SERVICE SPECIFICATIONSEngine Mechanical (3S±FE)A±5