Page 673 of 2389
ASSEMBLY OF FRONT DOOR
(See page BO±3)
1. BEFORE INSTALLING PARTS, COAT THEM WITH MIP
GREASE
(a) Coat the sliding surface and gears of the window
regulator with MP grease.
NOTICE: Do not apply MP grease to the spring of the win-
dow regulator.
13. REMOVE DOOR LOCK
(a) Disconnect the links from the door outside handle
and door lock cylinder.
(b) Remove the three screws and the door lock.
(c) (w/ Power Door Lock)
Remove the screw and door lock solenoid. 12. REMOVE FRONT DOOR BELT MOULDING
(a) Remove the screw.
(b) Pry loose the clips from the edge of the panel and re-
move the front door belt moulding.
14. REMOVE DOOR OUTSIDE HANDLE AND DOOR
LOCK CYLINDER
(a) Remove the two bolts and door outside handle.
(b) Remove the clip and door lock cylinder.
(b) Coat the sliding surface of the door lock with IMP
grease.
± BODYFront DoorBO±7
Page 674 of 2389
3. INSTALL DOOR LOCK
(a) (w/ Power Door Lock)
Install the door lock solenoid to the door lock with the
screw.
(b) InstalI the door lock with the three screws.
(e) Install the links to the door outside handle and door
lock cylinder. 2. INSTALL DOOR OUTSIDE HANDLE AND DOOR LOCK
CYLINDER
(a) Install the door outside handle with the two bolts.
(b) Install the door lock cylinder with the clip.
4. INSTALL FRONT DOOR BELT MOULDING
(a) Insert the claw of the clips into the upper panel hole
and push the front door belt moulding onto the panel.
(b) Install the screw.
7. INSTALL WINDOW REGULATOR
Place the regulator through the service hole and install the
five mounting bolts. 5. INSTALL FRONT LOWER FRAME
Install the front lower frame with the two bolts.
6. INSTALL REAR LOWER FRAME
± BODYFront DoorBO±8
Page 675 of 2389
(b) With the door glass fully closed, .adjust the door glass
stopper so it lightly makes contact with the glass
plate.
11. INSTALL OPENING CONTROL LINK
12. INSTALL SERVICE HOLE COVER
13. INSTALL DOOR TRIM8. INSTALL DOOR GLASS
(a) Place the glass in the door cavity.
(b) Install the glass to the regulator with the two mount-
ing nuts.
9. INSTALL DOOR GLASS RUN
14. INSTALL REAR VIEW MIRROR
(a) Install the mirror with the three screws.
(b) (Electrical type)
Connect the connector.
(c) Install the cover.
(d) (Manual type)
Install the knob with the setting screw.
15. INSTALL DOOR INSIDE HANDLE
(a) Connect the handle to the control link.
(b) Install the handle, slide it rearward, and install the
screw. 10. ADJUST DOOR GLASS
(a) Adjust the equalizer arm up or down and tighten it
where dimensions A and6, as shown, are equal.
± BODYFront DoorBO±9
Page 676 of 2389
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are ad-
justed correctly.
(b) Adjust the striker position by slightly loosening the
striker mounting screws, and hitting the striker with a
hammer.
Tighten the striker mounting screws again.
ADJUSTMENT OF FRONT DOOR
1. ADJUST DOOR IN FORWARD/REARWARD AND
VERTICAL DIRECTIONS
Using SST, adjust the door by loosening the body side
hinge bolts.
SST 09812±00010 16. INSTALL REGULATOR HANDLE
With door window fully closed, install the plate and regula-
tor handle with a snap ring as shown.
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
± BODYBO±10
Page 677 of 2389
REAR DOOR
COMPONENTS
± BODYRear DoorBO±11
Page 678 of 2389
(b) Insert a screwdriver between the trim retainers and
the door panel to pry it loose.
HINT: Tape the screwdriver tip before use.
4. REMOVE SERVICE HOLE COVER
5. REMOVE DOOR GLASS RUN
DISASSEMBLY OF REAR DOOR
1. REMOVE REGULATOR HANDLE
(w/o POWER WINDOW)
Pull oft the snap ring with a cloth and remove the regulator
handle and plate.
6. REMOVE DIVISION BAR
(a) Remove the two screws under the weatherstrip.
(b) Remove the bolt.
(c) Pull out the division bar. 2. REMOVE DOOR INSIDE HANDLE
(a) Remove the screw, and slide the handle forward.
(b) Disconnect the control link and remove the handle.
3. REMOVE DOOR TRIM WITH INNER WEATHERSTRIP
(a) Remove the two screws from the armrest.
± BODYRear DoorBO±12
Page 679 of 2389
8. REMOVE WINDOW REGULATOR
(a) (w/ Power Window)
Disconnect the connector.
(b) Remove the regulator ±mounting bolts.
(c) Remove the equalizer arm bracket mounting bolts. 7. REMOVE DOOR GLASS
(a) Wind the glass down into the door cavity.
(b) Remove the two glass channel mounting nuts.
9. REMOVE REAR DOOR BELT MOULDING
Pry out the rear door belt moulding with the clip as shown.(c) Remove the door glass by pulling it upward.
(d) Remove the regulator through the service hole.
± BODYRear DoorBO±13
Page 680 of 2389
12. REMOVE DOOR LOCK
(a) Disconnect the link from the door outside handle.
(b) Remove the three screws and door lock.
(e) (w/ Power Door Lock)
Remove the screw and door lock solenoid. 10. REMOVE INSIDE LOCKING LINK AND KNOB
Remove the bolt and disconnect the link from the door
lock.
11. REMOVE OPENING CONTROL LINK
Disconnect the link from the door lock.
13. REMOVE DOOR OUTSIDE HANDLE
Remove the two bolts and door outside handle.
± BODYRear DoorBO±14