Page 9 of 2000
ENGINE - 2AZ-FE ENGINE
240EG46 181EG10
VVT-i ControllerIntake CamshaftExhaust
Camshaft
Chain
Te n s i o n e r
Chain Damper
Chain SlipperCamshaft
Va l v e
Lifter
Service Tip
The adjustment of the valve clearance is accomplished by selecting and replacing the appropriate
valve lifters.
A total of 35 valve lifters are available in 0.02 mm (0.008 in.) increments, from 5.06 mm (0.199 in.)
to 5.74 mm (0.226 in.). For details, refer to 2006 RAV4 Repair Manual (Pub. No. RM01M1U).
EG-12
VA LV E M E C H A N I S M
1. General
The VVT-i system is used to improve fuel economy, engine performance and reduce exhaust emissions.
For details of VVT-i system, see page EG-48.
The intake and exhaust camshafts are driven by a timing chain.
Along with the increase in the amount of valve lift, the shim-less type valve lifter is used. This valve lifter
increases the cam contact surface.
Page 10 of 2000

ENGINE - 2AZ-FE ENGINE
181EG11
VVT-i ControllerIntake CamshaftTiming Rotor
Exhaust Camshaft
Timing Sprocket
185EG25 181EG14
Cam Spring
Cam
Plunger
SpringChain
Te n s i o n e r
Chain Damper
Oil Jet
Chain TensionerChain SlipperEG-13
2. Camshaft
The intake camshaft is provided with timing rotor to trigger the camshaft position sensor.
In conjunction with the adoption of the VVT-i system, an oil passage is provided in the intake camshaft
in order to supply engine oil pressure to the VVT-i system.
A VVT-i controller has been installed on the front of the intake camshaft to vary the timing of the intake
valves.
3. Timing Chain
A roller chain with an 8 mm (0.315 in.) pitch is used to make the engine more compact.
The timing chain is lubricated by an oil jet.
The chain tensioner uses a spring and oil pressure to maintain proper chain tension at all times.
The chain tensioner suppresses noise generated by the timing chain.
A ratchet type non-return mechanism is used.
To achieve excellent serviceability, the chain tensioner is constructed so that it can be removed and
installed from the outside of the timing chain cover.
Page 11 of 2000
ENGINE - 2AZ-FE ENGINE
208EG07
VVT-i Controller
Camshaft Timing
Oil Control Valve
Oil Return
Hole
Oil PumpOil Filter Chain
Te n s i o n e r
01NEG33Y
Bypass
Va l v e
Relief
Va l v eMain Oil Hole
Oil Filter
Oil Pump
Oil StrainerChain
Te n s i o n e rCylinder Head
Exhaust
Camshaft
Journal
Oil Control
Va l v e
VVT-i Controller
Oil Pan
Intake
Camshaft
Journal
Crankshaft
Journal
Crankshaft
Pin
Oil Jet
Piston
Cylinder
Block
Barance
Shaft
Timing
Chain EG-14
LUBRICATION SYSTEM
1. General
The lubrication circuit is fully pressurized and oil passes through an oil filter.
The trochoid gear type oil pump is chain-driven by the crankshaft.
The oil filter is attached downward from the crankcase to improve serviceability.
Along with the adoption of the VVT-i system, the cylinder head is provided with a VVT-i controller and
a camshaft timing oil control valve. This system is operated by the engine oil.
Oil Circuit
Page 12 of 2000
ENGINE - 2AZ-FE ENGINE
01NEG34Y
Oil Jets
Check
Va l v e
Oil
Bottom Side View Oil Jet Cross SectionEG-15
Oil Capacity
Liters (US qts, Imp. qts)
Dry
5.0 (5.3, 4.4)
with Oil Filter4.3 (4.5, 3.8)
without Oil Filter4.1 (3.8, 3.1)
2. Oil Jet
Piston oil jets for cooling and lubricating the pistons are used in the cylinder block.
These oil jets contain a check valve to prevent oil from being fed when the oil pressure is low. This prevents
the overall oil pressure in the engine from dropping.
Page 13 of 2000
ENGINE - 2AZ-FE ENGINE
01NEG35Y
Throttle Body
To H e a t e r C o r e
To R a d i a t o r
Thermostat
From Radiator Wa t e r P u m pBypass Passage
01NEG59Y
Bypass PassageCylinder Head
Wa t e r P u m p
Cylinder Block
Thermostat
Reservoir
Ta n k
RadiatorThrottle
BodyHeater Core EG-16
COOLING SYSTEM
The cooling system uses a pressurized forced-circulation system with pressurized reservoir tank.
A thermostat with a bypass valve is located on the water inlet housing to maintain suitable temperature
distribution in the cooling system.
An aluminum radiator core is used for weight reduction.
The flow of the engine coolant makes a U-turn in the cylinder block to ensure a smooth flow of the engine
coolant. In addition, a bypass passage is enclosed in the cylinder head and the cylinder block.
Warm water from the engine is sent to the throttle body to prevent freeze-up.
The TOYOTA genuine Super Long Life Coolant (SLLC) is used.
System Diagram
Page 14 of 2000

ENGINE - 2AZ-FE ENGINEEG-17
Engine Coolant Specifications
Engine
Coolant
Ty p e
TOYOTA genuine Super Long Life Coolant
(SLLC) or similar high quality ethylene
glycol based non-silicate, non-amine,
non-nitrite and non-borate coolant with
long-life hybrid organic acid technology
(coolant with long-life hybrid organic acid
technology is a combination of low
phosphates and organic acids.) Do not use
plain water alone.
ColorPink
CapacityM/T6.6 (7.0, 5.8)Capacity
Liters (US qts, Imp. qts)A/T6.7 (7.1, 5.9)
MaintenanceFirst Time100,000 mile (160,000 km)Maintenance
IntervalsSubsequentEvery 50,000 mile (80,000 km)
ThermostatOpening TemperatureC (F)80 - 84 (176 - 183)
SLLC is pre-mixed (the U.S.A. models: 50 % coolant and 50 % deionized water, the Canada. models:
55 % coolant and 45 % deionized water). Therefore, no dilution is needed when SLLC in the vehicle is
added or replaced.
If LLC is mixed with SLLC, the interval for LLC (every 25,000 miles / 40,000 km or 24 months
whichever comes first) should be used.
You can also apply the new maintenance interval (every 50,000 miles / 80,000 km) to vehicles initially
filled with LLC (red-colored), if you use SLLC (pink-colored) for the engine coolant change.
Page 15 of 2000
ENGINE - 2AZ-FE ENGINE
01MEG32Y
Exhaust ManifoldIntake ManifoldMain Muffler
Sub Muffler
TWC
Air Cleaner TWC EG-18
INTAKE AND EXHAUST SYSTEM
1. General
The linkless-type throttle body is used to realize excellent throttle control.
ETCS-i (Electronic Throttle Control System-intelligent) is used to provide excellent throttle control. For
details, see page EG-43.
A plastic intake manifold is used for weight reduction.
A stainless steel exhaust manifold is used for weight reduction.
Page 16 of 2000
ENGINE - 2AZ-FE ENGINE
01MEG10Y
Charcoal FilterAir Cleaner Cap
Air Cleaner Element
(Nonwoven Fabric)
Service Tip
The charcoal filter, which is maintenance-free, cannot be removed from the air cleaner cap.
01NEG42Y
Throttle Position
Sensor
Throttle Control MotorEG-19
2. Air Cleaner
A nonwoven, full-fabric type air cleaner element is used.
A charcoal filter, which adsorbs the HC that accumulates in the intake system when the engine is stopped,
is used in the air cleaner cap in order to reduce evaporative emissions.
3. Throttle Body
The linkless-type throttle body is used and it realizes excellent throttle control.
A DC motor with excellent response and minimal power consumption is used for the throttle control motor.
The ECM performs the duty ratio control of the direction and the amperage of the current that flows to
the throttle control motor in order to regulate the opening angle of the throttle valve.